Weekly Autoclave Tasks in a Dental Office: Seals, Trays and Water Quality
What does a weekly autoclave check cover that daily monitoring does not?
Two different cycles are often confused. Load monitoring confirms that a specific cycle worked; equipment checks confirm that the sterilizer can still do its job. In Ontario, the regulatory expectation on monitoring is daily: the RCDSO standard and Public Health Ontario guidance call for a biological indicator for each sterilizer on each day it is used, and for each cycle type used that day. A weekly monitoring interval belongs to the United States baseline described by CDC and AAMI ST79, and it does not satisfy the Ontario expectation on its own.
Weekly tasks need the chamber cold, the door open and about twenty minutes of a hygienist's or assistant's time.

What belongs on the weekly autoclave checklist?
- Door gasket: wipe with a damp lint-free cloth, then inspect the whole circumference for cracking, glazing or a flattened edge. A gasket that has lost its shape will leak steam and lengthen cycles.
- Chamber drain strainer: remove and clear debris. A blocked strainer is a common cause of water pooling in the chamber at the end of a cycle.
- Reservoir: drain, rinse and refill with distilled water. Do not switch to tap water to save time.
- Trays and racks: clean them, then look for corrosion or a bent runner that stops a cassette from seating squarely.
- Door hinge and latch: check for play, and lubricate only if the manufacturer's manual specifies a product and interval.
- Printer and records: confirm the cycle printout is legible and that your monitoring log has an entry for every day the practice was open.
- Ultrasonic cleaner: drain the solution, clean the tank, and check the timer and heater against the instrument manufacturer's instructions.
| Weekly task | Time | Warning sign |
|---|---|---|
| Gasket inspection and wipe | 3 min | Cracking, glazing, steam at the door |
| Chamber drain strainer | 3 min | Water left in the chamber |
| Reservoir drain and refill | 5 min | Scale or a white film in the tank |
| Trays, racks and cassettes | 5 min | Corrosion, bent runners |
| Log review and printout check | 5 min | Missing days in the monitoring log |
Why does autoclave water quality matter?
Steam quality depends on the water going in. Hard water leaves scale on heating elements and in the chamber, which lengthens cycles and eventually trips a fault code. Most benchtop units in Canadian dental offices are specified for distilled or demineralised water, and the manual will say so. On well water or in a hard-water area, test once a year and consider a small still rather than bottled water.
Consumables feed directly into these checks. Fresh sterilization indicator tape belongs on the shelf where the weekly log is kept so the two are checked together, sterilization roll stock should be stored away from heat and sunlight, and a benchtop ultrasonic cleaner takes the same weekly solution change discipline as the sterilizer.

Should weekly autoclave tasks be written down?
Keep a single sheet per sterilizer: date, task, initials, and any finding. When a gasket is replaced, note the date so the next interval is based on your practice rather than the calendar. The log also shows that equipment checks were not skipped when the office was short-staffed.
References
- RCDSO — infection prevention and control standards and guidelines
- Public Health Ontario — infection prevention and control resources
If you are rebuilding the monitoring side of the routine, a 24-hour biological indicator 25-pack is free with shipping included and gives five documented cycles to start with.
Ordering for a clinic, lab or care home? Wholesale and multi-site ordering covers case pricing and account setup, and the B2B wholesale collection lists the lines stocked for institutional buyers.
Weekly autoclave tasks cover seals, trays and water quality, and the monitoring result is what shows the week's cycles held. A 24-hour biological indicator 25-pack is available to Canadian clinics, long-term care homes and laboratories, and we cover the shipping.
Where to Buy Biological Indicators in Canada
CliniEco Medical supplies these from Ontario with published CAD pricing (MDEL #35334) — no quote required, and each pack ships with the lot number printed on it so your monitoring record stays traceable.
| Format | Pack size | Price (CAD) | |
|---|---|---|---|
| 24-hour self-contained | 25-pack | $69.99 | Order |
| 24-hour self-contained | 100-pack | $189.00 | Order |
| 3-hour rapid fluorescence | 50-pack | $249.99 | Order |
Round Out Your Sterilization Setup
A biological indicator is one link in the chain — these are the pieces it works with:
- Sterilization pouches — Class 4 dual-indicator, 200-pack — the packaging the indicator rides inside
- Class 5 chemical integrators — 100-pack — the in-pack check that pairs with your biological indicator
- Constant-heat pouch sealer — 200 °C, 12 mm seal — for consistent pouch closures
Which format does your sterilizer actually need?
Match the readout time to how fast you need the result: a 24-hour self-contained indicator works in any gravity or pre-vacuum cycle with a standard incubator, while a 3-hour fluorescence tube needs the matching reader. Running one cycle type per day, the 25-pack covers a month; busier clinics move to the 100-pack and cut the per-test cost.
How much do spore tests cost in Canada?
Published pricing runs $2.80 per test on the 25-pack down to $1.89 on the 100-pack — no distributor quote, no account needed.
Not sure which format your sterilizer needs? Generate a free sterilization log sheet first — it maps your cycles and tells you the pack size that fits. Questions about your setup? Ask a Compliance Specialist.
Related Reading
- CliniEco sterilization compliance hub
- Autoclave maintenance checklist: daily, weekly and monthly checks
- Autoclave tape inconclusive result: a faded or uneven strip
- What is a Class B autoclave? Chamber design and cycle types
- dental clinic sterilization supplies
- free Ontario sterilization compliance log
- printable autoclave sterilization log sheet (free)
Frequently Asked Questions
How often should a dental autoclave door gasket be replaced?
There is no single interval that fits every practice. Inspect it weekly and replace when you see cracking, glazing or a flattened edge, or when cycles start running long or steam escapes at the door.
Is weekly spore testing enough in Ontario?
No. Ontario expects a biological indicator for each sterilizer on each day it is used, and for each cycle type used that day. Weekly monitoring is the CDC and AAMI ST79 baseline used in the United States.
Do I need distilled water in a dental autoclave?
Follow the manufacturer's specification, which for most benchtop units is distilled or demineralised water. Tap water leaves scale that shortens element life and can cause cycle faults.
What should the weekly autoclave log include?
Date, task performed, initials and any finding or action taken, kept with the daily load monitoring records for the same sterilizer.
What should I do if a weekly check finds a fault?
Take it out of service until the fault is corrected, and record the finding, date and action on that unit's log sheet.
Last updated: September 2026. CliniEco Medical holds MDEL #35334 issued by Health Canada, and supplies clinics, long-term care homes and home-care programs across Canada.