Root Elevator Straight: Sizes, Markings and Colour Codes Explained
A straight root elevator carries three different numbering systems on a surface the length of a finger, and only one of them is a size. The pattern name tells you the shape. The blade width in millimetres tells you the instrument. The rest — a maker’s line code, a coloured handle, sometimes a third number in a catalogue column — identifies a product family, not a dimension.
That distinction decides whether a replacement order is repeatable. Two elevators can both be labelled Apexo, both be straight, and still differ in blade width by a millimetre, which is the difference between lifting a root and fracturing a buccal plate. The instrument that survives the case is the one whose width is written down, not the one whose name was remembered — and the same paperwork that carries the width carries the pack it went into: a Class 4 pouch with a cycle record, since an elevator is a critical instrument by any contact classification.Which of the three numbers on a handle is the size?
The blade width, quoted in millimetres. Everything else on the shank is an identifier. Pattern names such as Apexo, Seldin, Cryer and the luxating family describe the shape of the blade and the way it engages the periodontal ligament; the catalogue number that accompanies them identifies the pattern, not a dimension. A maker’s colour is a product line.
| Marking | Example | Is it a size? | What to do with it |
|---|---|---|---|
| Pattern name | Apexo 301, Seldin 34S | No | Use it to name the shape you want |
| Pattern number | 301, 34S, 3S | No | Cross-reference it between makers, never treat it as mm |
| Blade width | 2 mm, 3 mm, 4 mm | Yes | This is the field to record and to reorder by |
| Curve | Straight or curved | No | A separate instrument line, not a size variation |
| Handle colour or band | A coloured ring or coated handle | No | A maker’s range marker; check the etch instead |
| Length | Handle length as catalogued | Not usually | Affects access and leverage, not the lift |
The trap is that the pattern number looks like a size. In several catalogues a 34S, a 3S and a 301 sit next to widths of 2, 3 and 4 mm, so a reorder written from memory mixes a name and a number and arrives as the wrong instrument. Written as “Seldin 34S, 3 mm width” there is nothing to confuse.

Is there an ISO colour code for elevators?
No. The ISO colour systems that a dental team learns are the endodontic file wheel and the diamond bur grit rings; neither applies to a hand elevator. Colour on an elevator handle is a manufacturer’s range marker — a coloured coated handle, a coloured ring, a pattern-specific finish — and the same colour in two makers’ ranges can mean two different things or nothing at all.
The practical consequence is that colour should never be the field a reorder is built on. It is a useful way to keep one maker’s series together in a tray, and it is a fast way to see that an instrument has been put back in the wrong place. It is not a specification, and a clinic that writes “the red one” on a purchase request has written something that no supplier can fill.
| Colour system | Applies to | Meaning of the colour |
|---|---|---|
| ISO file colour wheel | Endodontic hand and rotary files | The ISO size number of the file |
| Diamond grit ring | Diamond burs | The grit: coarse to ultra-fine |
| Carbide cut code | Carbide burs | The blade cut, in the ISO 6360 number block four |
| Elevator handle colour | Hand elevators | A maker’s range or line — no standard meaning |
| Instrument marking tape | Cassettes and trays | An in-house identification choice |
What does the marking tell you about how the instrument should be used?
Shape, mostly. A straight elevator is a lever whose working end is a blade; a luxating elevator in the same catalogue is described as having a thin, sharp blade intended to cut the periodontal ligament rather than to lift against bone. Those are different instruments with different failure modes, and the difference is visible in the blade rather than in the number.
Width then sets the case. A 2 mm blade works where the space is narrow and the tissue is the constraint; a 4 mm blade moves a root with fewer passes but loads a thinner wall. Neither is “better”; the field to record is which width was used, because that is what makes the next case predictable and what makes a reorder correct.

Why do the etched markings matter more than the catalogue?
Because a catalogue is not in the room. The etch on the shank is what a clinician reads to confirm that the instrument handed over is the instrument asked for, and it is the only field that survives sterilisation. It also ages: repeated reprocessing dulls a laser etch, and an instrument whose width can no longer be read has lost its specification even though its shape is intact.
Inspection therefore has two parts. The first is the blade — an edge that has been rolled, chipped or bent is a replaced instrument, not a resharpened one, because the geometry that makes an elevator work is the geometry that a bench grinder destroys. The second is the mark — if the width cannot be read, the instrument goes into the tray as an unknown, and an unknown is what gets chosen wrongly at the wrong moment.
| What to check | Pass | Fail and the action |
|---|---|---|
| Blade width etch | Legible against the catalogue entry | Mark it, or withdraw it from the tray |
| Blade edge | Continuous, no reflection break | Replace; do not resharpen in house |
| Blade to shank junction | No crack, no bend | Replace |
| Handle and ferrule | No looseness when twisted | Replace — a rotating handle is a hand injury |
| Pattern identification | Matches the tray list | Return to the correct position and label the tray |
Where does a clinic take this next?
Three things here are usable rather than readable. The printable compliance log holds the fields a receiving check, a lot trace and a reprocessing record actually need, so the paperwork can be introduced without inventing a format. The clinic supply planner keeps the pouch count in step with the extraction kit, so a tray that goes back into the sterilizer never waits on packaging. The dental compliance hub collects the rest of the chairside and instrument guides for this setting, and the dental clinics collection is where the consumables that surround the tray are grouped. Multi-site or purchasing-group enquiries go through the wholesale account route, where case quantities and delivery frequency are set once rather than per order. Reselling? become a distributor.
Questions that go past a template — a record format a particular inspector asked for, or a retention period your college is challenging — belong with the compliance consultation desk rather than a generic contact form.
Related Reading
- Dental Extraction Forceps #150: Sizes, Markings and Colour Codes Explained
- Williams Periodontal Probe: Sizes, Markings and Colour Codes Explained
- Instrument Reprocessing Workflow: Clean, Disinfect, Sterilize Explained
Frequently Asked Questions
Do root elevators have an ISO colour code?
No. The standardised colour systems in dentistry are the endodontic file wheel and the diamond bur grit rings. A colour on an elevator handle is a manufacturer’s range marker, and it carries no dimension that can be relied on across brands.
What does the number on a straight elevator mean?
Usually a pattern number, not a size. Apexo 301 and Seldin 34S identify shapes; the dimension is the blade width in millimetres, which is quoted separately in the catalogue and etched on the instrument.
What is the difference between a straight elevator and a luxating elevator?
A luxating elevator is catalogued with a thin, sharp blade intended to cut the periodontal ligament; a straight elevator is a lever working against the tooth or the interspace. The blade geometry differs, so the two are separate instrument lines rather than sizes of one pattern.
How do I order a replacement when the etch has worn off?
Order by pattern name plus blade width from the practice’s own tray list, and treat the unreadable instrument as an unknown until it is measured or replaced. A reorder written from colour alone cannot be filled correctly by a supplier.
Should an elevator be sharpened in house?
A blade that has been rolled or chipped is normally replaced rather than resharpened, because the working geometry is set by the manufacturer and a bench sharpening changes the width and the bevel that make the instrument predictable.
CliniEco Medical holds Health Canada MDEL #35334. Pattern names and blade widths follow the catalogues cited above; instrument selection and technique remain clinical decisions. This page is general information about instrument markings, cataloguing and record-keeping, not clinical or legal advice. Confirm the current specification, part number and order status on the product page, and confirm the current wording of any standard with the body that publishes it. Health Canada MDEL #35334 covers our establishment licence; it is not a statement about any individual product.