Which Standards Apply to Ultrasonic Dental Cleaner CS6.2 in the US vs Canada? Sizes and Sourcing

Which Standards Apply to Ultrasonic Dental Cleaner CS6.2 in the US vs Canada? Sizes and Sourcing

Two cartons leave the same factory. One lands on a bench in Buffalo, the other in Brampton. The tank, the transducers, the basket and the timer are identical; what differs is who has to hold a licence before the unit can be sold, which standard the cleaning step is measured against, and what the practice has to be able to show an inspector afterwards. The 6 L benchtop ultrasonic cleaner CS6.2 is the unit this comparison uses, because 6 L is the size at which a standard dental instrument cassette fits in one cycle — and the cassette is what turns a bench cleaner into a reprocessing step rather than a soaking tub.

CliniEco CS6.2 6 L benchtop ultrasonic cleaner with lid fitted, front view
The CS6.2 is a 6 L class bench unit: the tank size at which a full dental instrument cassette fits in one cycle.
Close-up of the CS6.2 control panel showing the heater dial and digital timer display
Heater dial with three positions, 40, 50 and 60 degrees Celsius, next to the digital timer: the two readings a paper record needs.

Does the CS6.2 need a licence in Canada, and does it need one in the United States?

The United States writes the classification down. 21 CFR 880.6150 identifies an ultrasonic cleaner for medical instruments as a device intended for cleaning medical instruments by the emission of high frequency soundwaves, places it in Class I, and exempts it — together with any solution intended for use with it — from premarket notification, subject to the limitations in 21 CFR 880.9. No 510(k) is filed for a benchtop cleaner that fits that identification. What remains is establishment level: a manufacturer or initial importer registers its establishment and lists the device under 21 CFR Part 807. A listing records who and what; it is not a review of the machine.

Canada runs the paperwork the other way round. A device licence is the instrument for Class II to Class IV devices, and section 32 of the Medical Devices Regulations sets out what such an application must contain — condition, intended use, standards complied with, attestations. A Class I device never enters that queue. What section 44(1) does require is an establishment licence before a person imports or sells a medical device, with 44(2) exempting a retailer, a health care facility, a manufacturer of a Class II to IV device, and a Class I manufacturer that distributes only through a licensed establishment. That licence belongs to the establishment, not to the product. The importer here is CliniEco Medical, MDEL #35334, and that number identifies who may import and distribute; it does not certify the tank.

Labels carry a second difference that buyers notice at the carton rather than at the bench. Under section 23 of the same regulations, the required label information must be in at least one official language, the other language must be made available as soon as possible at the purchaser's request, and both languages are mandatory only for a device sold to the general public. In practice: a professional buyer can be served in one language, but asking for the other is a right, not a favour.

Point Canada United States
Device class Class I Class I under 21 CFR 880.6150
Premarket review No device licence for Class I Exempt from premarket notification
Who holds the licence The importer or distributor, under section 44 The establishment, by registration and listing
What the licence proves That the establishment may import and sell That the establishment and device are recorded
Label language One official language minimum; the other on request English
Where a buyer checks it MDEL listing, searched by company Establishment registration and device listing

Which standard is the cleaning step measured against on each side?

In Canada the operating standard is CSA Z314:23, Medical device reprocessing in all health care settings. The clauses a dental bench actually touches are set out in the Alberta Health Services MDR review criteria that map Z314:23. Gross soil is removed before immersion (11.6.6.2). The solution is changed at least daily, and fresh solution is degassed as the manufacturer instructs (11.6.6.5). The cleaner is monitored daily with a commercial test product and the result is recorded (11.6.6.6). Instruments are rinsed after cleaning as the instrument maker requires (11.6.7.1). A plan exists for what happens when automated equipment is out of service (18.1.1). And Annex G requires the manufacturer's instructions to cover installation including water quality, operation, daily, routine and preventive maintenance, and the daily sonication test. The same mapping records that foil testing is not acceptable as that monitoring.

A second standard is quoted often at the point of sale and needs narrowing before it means anything. ISO 15883-1:2024 gives general requirements for washer-disinfectors, and ISO 15883-5:2021 sets the test methods for cleaning efficacy. A benchtop ultrasonic bath that cleans and does not disinfect is not a washer-disinfector, so a claim of ISO 15883 conformity has to be finished as a sentence: which part, and is there a disinfection stage with a stated A0 value. Where there is no disinfection stage, the unit is cleaning equipment and the sterilizer downstream carries the disinfection and sterilization duties.

The United States regulates the device, not the daily routine of the tank. The operating expectation arrives from two other directions. One is the instrument manufacturer's validated reprocessing instructions, the subject of the FDA guidance on reprocessing medical devices in health care settings, which puts validation data and labelling on the device maker and makes the clinical step follow those instructions. The other is ANSI/AAMI ST79, the consensus practice standard for steam sterilization, whose cleaning chapter treats mechanical cleaning equipment as equipment to be monitored against the equipment maker's written instructions rather than against a federal frequency table.

Requirement Canada, CSA Z314:23 route United States, IFU and ST79 route
Gross soil before immersion Required before the cycle (11.6.6.2) Required by the instrument maker's instructions
Solution change At least daily, plus degassing of fresh solution (11.6.6.5) Per the cleaner manufacturer's instructions
Performance check Daily, commercial test product (11.6.6.6) Per the written instructions; ST79 treats the equipment as monitored
Record of the check Required, kept with reprocessing records Kept as part of the practice's sterilization record
Rinse after cleaning As the instrument maker requires (11.6.7.1) As the instrument maker requires
Water quality at installation In the manufacturer's instructions, Annex G Utility requirement in the equipment instructions
Equipment downtime Contingency plan required (18.1.1) Practice policy and accreditation survey

What does the CS6.2 state about itself, and what does it leave to the paper record?

The specification that matters for a reprocessing decision is short enough to read in one screen.

Field CS6.2 statement Why a reprocessing lead asks
Tank capacity 6 L class, SUS304 stainless tank Holds a full instrument cassette in one cycle
Tank dimensions 31.1 x 17.2 x 11.6 cm Fits the cassette and leaves room for the basket
Frequency Dual, 32 kHz and 48 kHz Lower frequency for heavier soil, higher for fine crevices
Heating Two ceramic heaters, 40 to 60 degrees Celsius A set-point that can be written down each cycle
Timer Digital timer to 30 minutes, 120 second degas The degas cycle belongs to the start of the day, not to guesswork
Power 320 W, AC 100 to 120 V, 60 Hz North American supply, no transformer
Electrical certification cETL by Intertek to CSA C22.2 No. 68 and UL 73 Appliance safety on both sides of the border
Basket SB01 stainless basket included, re-orderable A worn basket is a part, not a new machine
Cycle data export None; no logger and no USB export Records are paper, signed, and that is acceptable

The certification line is the one most often misread. cETL to CSA C22.2 No. 68 and UL 73 is an appliance safety certification for motor-operated equipment; it says the unit was tested to the Canadian and US appliance standards named on it. It says nothing about cavitation distribution, cleaning efficacy or the daily test. Those belong to Z314:23, to the instrument maker's instructions and to the practice's own written procedure. A clinic that treats the mark on the back as cleaning validation has bought the wrong assurance.

The absence of a logger is not a defect, but it is a design fact a buyer should price in. Under Z314:23 the documentation obligation sits inside the reprocessing quality system, so a signed paper line is not a lesser record — it is the record the standard asks for. Five fields per cycle cover it: date, operator, temperature set-point, cycle length, and the date the solution was last changed. The readable set-point and the counting timer exist so those five can be written down without reconstructing them at the end of the shift.

Sizes: what decides the tank, and what does not?

The standard sets the test, the record and the rinse. It does not set a tank volume, and any page that implies a regulated tank size is inventing one. The physical constraint is the cassette, and the break points are simple.

  • Under 3 L: handpieces, retainers and loose instruments. Workable for a hygiene room that does not cassette, awkward for anything else.
  • 6 L: a full cassette in one cycle. This is the size that removes the second run of the morning.
  • 8 L and above: several cassettes or a lab batch. The tank is right when the load is right, and oversized tanks carry a cost in solution per cycle as well as in purchase price.

Two placement rules come from practice rather than from the standard: instruments go in the basket, never on the tank floor, and hinged instruments are opened so the solution reaches the joint.

What belongs on a cross-border purchase order?

A purchase order that has to survive a records review should name the parts that carry obligations, not just the machine:

  • The SKU and the certification mark, so the article ordered is the article certified: CLI-ULTRA-CLEAN-62, cETL to CSA C22.2 No. 68 and UL 73.
  • Supply voltage and frequency, stated as 100 to 120 V and 60 Hz, so nobody ships a 220 V variant into a North American bench.
  • The basket as a line item: SB01, quantity two if the practice runs one in service and one drying.
  • The ultrasonic multi-enzyme cleaning solution separately, because the solution is a consumable with its own dilution and change interval and is not part of the machine order.
  • The manual language, English and French, and the importer of record with MDEL #35334 named on the invoice.
  • Service terms, because a bench cleaner out of service is a reprocessing stop, and 18.1.1 asks the practice to have planned for that day.

Buyers who want the size comparison across the range rather than the standards view can start from the ultrasonic cleaner collection.

Where does a clinic take this next?

Four things a clinic can act on rather than read: a printable compliance log sheet that records receiving dates, lot numbers and open-on dates and exports from the browser; the clinic supply planner that turns daily bench counts into cases per month; and, where a finding has to be documented for an inspector, Ask your compliance question which returns a written answer citing the regulation or standard it rests on.

Facility and multi-site buyers can also ask about wholesale and multi-site ordering for case pricing and account setup. Reselling? become a distributor.

Related reading

Frequently Asked Questions

Does a Class I ultrasonic cleaner need a device licence in Canada?

No. Device licence applications under section 32 of the Medical Devices Regulations are the route for Class II to Class IV devices, and a Class I device does not go through that queue. The licence that does apply is the establishment licence in section 44, held by the importer or distributor — here CliniEco Medical, MDEL #35334 — and it authorises import and sale rather than approving the machine.

Is a 6 L bench ultrasonic cleaner a washer-disinfector under ISO 15883-1?

Only if it has a disinfection stage that can be stated, normally as an A0 value at a defined temperature and hold time. A bath that cleans at 40 to 60 degrees Celsius and does not claim disinfection is cleaning equipment, and the sterilizer downstream carries the disinfection and sterilization duties. A supplier claiming ISO 15883 conformity should be asked which part, and what the disinfection stage is.

What has to be recorded after each ultrasonic cycle?

Five fields cover the cycle itself: date, operator, temperature set-point, cycle length and the date the solution was last changed. Separately, CSA Z314:23 clause 11.6.6.6 asks for a daily performance check with a commercial test product and a record of that result. A unit without a logger is not exempt; the record simply moves to paper.

Does the foil test satisfy CSA Z314:23?

Not as the daily monitoring step. The Alberta Health Services criteria that map Z314:23 record that foil testing is not acceptable, and clause 11.6.6.6 asks for a commercial test product with the result recorded. A foil test can still be run as an internal check, but it does not stand in for the documented test.

Does a dental practice in the United States have the same daily test duty?

There is no federal rule that sets a daily test for a dental ultrasonic cleaner. What applies is the instrument manufacturer's validated instructions, which the FDA reprocessing guidance makes the reference point for the clinical step, and the cleaning chapter of ANSI/AAMI ST79, which treats mechanical cleaning equipment as monitored against the equipment maker's written instructions. State practice rules and accreditation surveys can add to that.

Will a 4 L ultrasonic cleaner take a full instrument cassette?

Normally not. The cassette is the practical size break: under 3 L a unit handles handpieces and loose instruments, 6 L takes a full cassette in one cycle, and 8 L and above are bought for several cassettes or a laboratory batch. Measuring the cassette and the tank opening is the two minute check that prevents a second run every morning.

Sources

  • 21 CFR 880.6150, Ultrasonic cleaner for medical instruments — ecfr.gov
  • 21 CFR 880.9, Limitations on exemptions — ecfr.gov
  • 21 CFR Part 807, Establishment registration and device listing — ecfr.gov
  • Medical Devices Regulations (SOR/98-282), sections 23, 32 and 44 — laws-lois.justice.gc.ca
  • Medical device establishment licence listing — health-products.canada.ca
  • CSA Z314:23, Medical device reprocessing in all health care settings — csagroup.org
  • Alberta Health Services, MDR review criteria supporting standards, Z314:23 clause map — albertahealthservices.ca
  • ISO 15883-1:2024, Washer-disinfectors, general requirements — evs.ee
  • ISO 15883-5:2021, Test soils and methods for demonstrating cleaning efficacy — evs.ee
  • ANSI/AAMI ST79, Comprehensive guide to steam sterilization and sterility assurance — aami.org
  • FDA, Reprocessing medical devices in health care settings, validation methods and labeling, 2015 — govinfo.gov
  • Public Health Ontario, PIDAC provincial guidance on cleaning, disinfection and sterilization of medical equipment — publichealthontario.ca
  • CSA C22.2 No. 68-18, Motor-operated appliances — csagroup.org
  • UL 73, Motor-operated appliances — shopulstandards.com
  • ISO 17664-1:2021, Information to be provided for reprocessing of medical devices — evs.ee

CliniEco Medical distributes clinic and laboratory consumables in Canada under MDEL #35334. Requirements that bind a specific practice remain the ones in its own provincial guidance, manufacturer instructions and written procedures.

Last updated: 19 November 2026.

Already working with clinics? Become a regional representative.