Which Standards Apply to 95 kPa Specimen Bags 6×9–12×15 Inches in Alberta Clinics?

Three 95 kPa specimen safety bags showing the fold-and-seal instruction printed on the bag

Which Standards Apply to 95 kPa Specimen Bags 6×9–12×15 Inches in Alberta Clinics?

A clinic in Red Deer finishes a Tuesday morning run: four EDTA tubes, two urine containers, a swab in transport medium and a tissue pot. Each one leaves the treatment room in a plastic bag with a document pouch, and nobody in the room could say which standard that bag is built to. The question is worth an answer, because in Alberta the answer changes twice: once for the type of specimen, and once for how it travels.

Start with the object. A 95 kPa specimen bag with a two-pocket design and a document pouch is sold in four footprints — 6×9, 7×11, 8×10 and 12×15 inches — and the four sizes exist because the primary receptacle decides the bag, not the other way round. A 6×9 bag holds a rack of blood tubes or a single urine container; a 12×15 bag holds a histology pot or several containers travelling to the same lab.

The commercial question is simple and the compliance question is not. Below is the actual standard stack: the federal transport rules, the packaging standard they import, what the 95 kPa number measures, and the Alberta accreditation layer that sits over the whole chain.

Which standards apply to a 95 kPa specimen bag in Alberta?

Two federal statutes, one packaging standard, and a provincial accreditation programme. The bag itself is not certified by anybody, which is the first thing buyers get wrong.

Document or standard What it fixes Where it bites
Transportation of Dangerous Goods Act, 1992 The legal duty to classify, package, mark and document Every consignment offered for transport in Canada
TDG Regulations, SOR/2001-286 Sections 1.39, 1.42 and Part 5 set the exemptions and the means of containment The bag, the mark and the paperwork
CAN/CGSB-43.125 Design, testing and marking of Type P650 packaging The 95 kPa design and test requirement
Packing Instruction P650 (UN Recommendations) The international equivalent, imported for foreign-made packaging Imported bags
ISO 15189:2022 and ISO 15190:2020 Laboratory quality and laboratory safety The sending laboratory
CSA Z316.6:20 Sharps containers, not bags A different purchase entirely

The line that surprises people is the second from the bottom. The TDG Regulations never print a pressure figure. Instead, section 1 of the regulations defines a Type P650 means of containment as one that complies with CAN/CGSB-43.125, or, if it was manufactured outside Canada, with Packing Instruction P650 of the UN Recommendations. That definition is where the 95 kPa test enters Canadian law, and it is why a spec sheet that says "95 kPa certified" without naming a standard is telling a buyer almost nothing.

Does every specimen leaving an Alberta clinic need a 95 kPa bag?

No, and this is the point where clinics overspend on packaging or, worse, mislabel it. The TDG Regulations carry a specific exemption for human and animal specimens.

Section 1.42 removes Parts 3 to 8 and Part 17 for specimens where a competent professional has determined there is a minimal likelihood that infectious substances are present. The determination has to consider the medical history, the symptoms, the relevant circumstances of the person and the endemic local conditions. The packaging that route requires is marked "Exempt Human Specimen" — or "spécimen humain exempté" in French — and it must be designed, constructed, filled, closed, secured and maintained so that there is no release under normal conditions of transport.

Route Which specimens Marking on the packaging 95 kPa packaging
Exempt human specimen, s.1.42 Routine diagnostic samples with minimal likelihood of infectious substances "Exempt Human Specimen" Not required
UN3373, Category B, s.1.39 Samples that may contain a Category B infectious substance Category B mark plus shipping name and 24-hour number Required
UN3291, medical waste, s.1.42.3 Clinical and medical waste Biohazard symbol and "BIOHAZARD" CGSB-43.125 packaging for waste

A 95 kPa specimen transport bag with adhesive seal, biohazard symbol and a separate document pouch for the requisition

Three practical consequences follow. First, a clinic that sends routine bloods and urines is usually shipping exempt specimens, and the 95 kPa bag is not the legal minimum for that journey — it is a higher specification the clinic chooses. Second, a sample that may carry a Category B substance has to travel in P650 packaging with the Category B mark, and the shipper carries the packing duty. Third, medical waste is a separate route again, and section 1.42.3 points at CGSB-43.125 packaging with a biohazard symbol rather than at the specimen bag.

Where clinics get into difficulty is the word "believed". Transport Canada's own guidance defines "no reason to believe" as having sufficient information available, none of which suggests the sample could contain a Category A or Category B substance. The judgment rests with a professional, and it is worth writing down who made it and on what basis, because that note is the thing an inspector asks for.

What does the 95 kPa figure actually test?

It is a pressure differential the packaging has to hold without leaking, and it is a design requirement rather than a grade stamped on a bag.

Under the Type P650 definition, a Canadian-made package complies with CAN/CGSB-43.125. Transport Canada's guidance states where the requirements for design, testing and marking of Type P650 packaging sit, and also states that facilities manufacturing this packaging in Canada are not required to register with the department. What a manufacturer must do instead is prepare and retain a design report under Annex A of the standard, so that compliance can be demonstrated.

That structure has a direct purchasing consequence. There is no registry to search and no certificate number to quote. A buyer who wants evidence gets a manufacturer's design report, a specification sheet that names the standard and the test, and a lot number that ties the bags in the cupboard to the production run. Anything described as "95 kPa certified" with no standard behind it is a marketing phrase.

The construction requirements are equally concrete, and they explain why a P650 package looks the way it does: a leakproof or siftproof primary receptacle, a leakproof or siftproof secondary packaging, and an outer packaging whose smallest external dimension is at least 100 mm, with either the secondary or the outer packaging rigid. When liquids travel, absorbent material sits between the primary receptacle and the secondary packaging in a quantity sufficient to absorb the entire contents of the primary receptacle.

Which size covers 6×9 to 12×15 inches, and what has to be printed on it?

Size follows the receptacle and the mark, in that order. The mark sets a floor: the Category B mark is a square on point with each side at least 50 mm, a line at least 2 mm wide and characters at least 6 mm high, the shipping name sits beside it in letters at least 6 mm high, and the 24-hour telephone number sits beside the shipping name. Section 1.39 adds that one external surface must measure at least 100 mm by 100 mm.

Bag footprint Typical load Why this size
6×9 in (152 × 229 mm) A rack of blood tubes, a urine container, a swab Smallest footprint that carries the mark cleanly
7×11 in Two containers, or a container plus a request form pouch Room for absorbent around the primary receptacle
8×10 in Several tubes plus a small pot The size most hospital labs standardise on
12×15 in Histology pots, multi-container consignments Volume, not pressure, is the constraint

Three 95 kPa specimen safety bags showing the fold-and-seal instruction printed on the bag

The two-pocket design is a documentation control, not a convenience. The specimen sits in the front pocket with the absorbent, and the requisition sits in the back pocket so the paperwork never shares a space with the sample. A 6×9 three-wall transport bag in a 1,000-bag case does the same job for a clinic whose samples travel by courier without a pressure requirement, and the difference between the two products is the design basis, not the wall count.

Primary receptacles belong in the same order. A 120 mL screw-cap specimen container and a 90 mL graduated sample cup both fit a 6×9 pocket, and both have to close without leaking before the bag matters at all.

Who accredits an Alberta laboratory, and what does that change for transport?

Alberta uses a provincial accreditation model rather than a federal one. Laboratories that perform and report diagnostic tests to guide patient care need to be accredited by the College of Physicians & Surgeons of Alberta, and the college sets facility standards for all aspects of diagnostic laboratory operations. Assessment happens on site when a facility opens, and facilities are reassessed on a four-year cycle, with reassessment triggered by a move, a renovation or a new service.

Two details matter to a clinic. The standards themselves are not public — they are issued to accredited labs through a secure portal and to applicants once fees are paid — so a supplier cannot read them and quote them back at a clinic. And point-of-care testing sits in a grey zone: the college directs physicians and primary care providers who report point-of-care results into Netcare and Connect Care to its diagnostic laboratory medicine accreditation team for guidance, while testing done purely for research or as third-party drug screening does not need accreditation.

On the public side, Alberta Health Services operates the provincial laboratory service that most samples are sent to, and the Public Health Act and the Health Professions Act set the framework within which the college adopts its standards. For a clinic buyer, this all lands in one place: the bag has to satisfy the transport rules, and the laboratory has to satisfy the accreditation standards.

Which standards sit behind the bag, rather than on it?

Five documents come up in supplier conversations and only two of them are transport documents.

ISO 11607-1:2019 governs packaging for terminally sterilized medical devices, and it is about maintaining sterility through handling and storage, not about containing a liquid through a courier journey. ISO 13485:2016 is the quality management system a manufacturer is audited against. ISO 15223-1:2021 supplies the symbols printed on packs and labels. ISO 15189:2022 is the laboratory quality standard, and ISO 15190:2020 is the laboratory safety standard that covers the handling side. ISO 23907-2:2019 is the reusable sharps container document, and no part of it applies to a bag.

A supplier who answers "ISO 11607" to a question about specimen transport has answered the wrong question, politely.

What should an Alberta buyer check before ordering?

Six checks, and they take one email:

  • The standard the bag is built to, named with its number, not a phrase
  • Whether the design basis is P650 or a leak-resistant three-wall construction
  • The mark printed on the bag, its dimensions and the shipping name placement
  • Whether absorbent is supplied with the bag or added separately
  • The 24-hour telephone number a courier will call, and who answers it
  • The lot number on the case, so a recall can be traced to a shelf

Running a diagnostic laboratory, a collection room or a clinic in Alberta? laboratory consumables and specimen handling supplies covers the collection and transport lines we stock. Ordering for a clinic, lab or care home? Wholesale and multi-site ordering covers case pricing and account setup, and the B2B wholesale collection lists the lines stocked for institutional buyers. Reselling? become a distributor.

References

  1. Transportation of Dangerous Goods Act, 1992, S.C. 1992, c. 34 — Department of Justice Canada (checked 3 November 2026)
  2. Transportation of Dangerous Goods Regulations, SOR/2001-286 (current to 19 October 2026) — Department of Justice Canada (checked 3 November 2026)
  3. TDG Regulations, Part 1 — sections 1.39, 1.41, 1.42 and 1.42.3 — Department of Justice Canada (checked 3 November 2026)
  4. TDG Regulations, Part 1 — definitions, including Type P650 means of containment — Department of Justice Canada (checked 3 November 2026)
  5. Shipping infectious substances — means of containment, Type P650 packaging and marking — Transport Canada (checked 3 November 2026)
  6. ISO 15189:2022 — Medical laboratories: requirements for quality and competence — Genorma (ISO/TC 212) (checked 3 November 2026)
  7. ISO 15190:2020 — Medical laboratories: requirements for safety — Genorma (ISO/TC 212) (checked 3 November 2026)
  8. ISO 11607-1:2019 — Packaging for terminally sterilized medical devices, Part 1 — Genorma (ISO/TC 198) (checked 3 November 2026)
  9. ISO 13485:2016 — Medical devices: quality management systems — Genorma (ISO/TC 210) (checked 3 November 2026)
  10. ISO 15223-1:2021 — Medical devices: symbols used with information supplied by the manufacturer — Genorma (ISO/TC 210) (checked 3 November 2026)
  11. ISO 23907-2:2019 — Sharps injury protection: reusable sharps containers — Genorma (ISO/TC 84) (checked 3 November 2026)
  12. Diagnostic Laboratory Medicine — Alberta laboratory accreditation — College of Physicians & Surgeons of Alberta (checked 3 November 2026)
  13. Facility accreditation — standards, assessment cycle and programs — College of Physicians & Surgeons of Alberta (checked 3 November 2026)
  14. Laboratory Services — Alberta Health Services (checked 3 November 2026)
  15. Public Health Act, RSA 2000, c P-37 — Alberta King's Printer (checked 3 November 2026)
  16. Health Professions Act, RSA 2000, c H-7 — Alberta King's Printer (checked 3 November 2026)

Printable companion: the free log and template centre includes a specimen handover sheet, so the bag lot, the courier pickup time and the staff member who sealed the bag sit on one page instead of in three memories.

Samples per week is the number that sets the bag order, and the clinic supply and cost planner turns that into boxes per month, which is what a case price should be measured against.

Related Reading

Frequently Asked Questions

Do 95 kPa specimen bags need a certificate?

No design-type approval is issued for this packaging. Transport Canada states that facilities making Type P650 packaging in Canada are not required to register with Transport Canada, but must prepare and retain a design report under Annex A of the CAN/CGSB-43.125 standard. A supplier can show that report; it is not a certificate, and no body stamps a bag as 95 kPa approved.

Is a 95 kPa bag required for every specimen an Alberta clinic sends out?

No. Section 1.42 of the TDG Regulations removes Parts 3 to 8 and 17 for human specimens where a competent professional has determined there is a minimal likelihood of infectious substances, considering history, symptoms, circumstances and local conditions. Those specimens travel in packaging marked "Exempt Human Specimen", not in UN3373 packaging. The 95 kPa requirement belongs to the Category B route.

What does the 95 kPa figure actually test?

It is an internal pressure differential the packaging has to hold without leakage. In Canada the requirement reaches a buyer through the definition of Type P650: a means of containment complying with CAN/CGSB-43.125 for Type P650 packaging, or, if made outside Canada, with Packing Instruction P650 of the UN Recommendations. The figure is a design and test requirement, not a label grade.

What must be printed on a Category B specimen bag?

The Category B mark, which is a square on point with each side at least 50 mm, a line width of at least 2 mm and letters and numbers at least 6 mm high. The shipping name sits next to the mark in letters at least 6 mm high, on a contrasting background, and the 24-hour telephone number sits next to the shipping name.

How small can the outer packaging be?

The outer packaging of a Type P650 package must have a smallest external dimension of at least 100 mm. Section 1.39 also requires one external surface of at least 100 mm by 100 mm, because the mark and the shipping name have to fit on it legibly. A bag below that footprint cannot carry the mark as written.

Can a specimen bag be reused?

The primary receptacle cannot be reused. Transport Canada's guidance allows the secondary inner packaging or the outer packaging to be reused where there is no visible contamination, damage or defect that could make the packaging unsafe for transport. A bag that carried a leaking container is therefore out of service, however clean the outside looks.

Does a three-wall specimen bag meet the 95 kPa requirement?

Not by construction alone. A three-wall bag is built for leak resistance on the bench and for a separate document compartment, and it is a different product from a P650 package. It can be the right choice for an exempt specimen that travels by courier, but it should not be described as 95 kPa rated unless the manufacturer's design report covers it.

Which standard covers the laboratory that sends the bag?

In Alberta, a laboratory that produces and reports diagnostic results for patient management has to be accredited by the College of Physicians & Surgeons of Alberta, and the accreditation standards cover all aspects of laboratory operations. ISO 15189:2022 and ISO 15190:2020 are the international quality and safety documents labs work to alongside that provincial programme.

Last updated: October 2026. CliniEco Medical is a licensed medical device establishment (MDEL #35334).

Already working with clinics? Become a regional representative.