Quick answer: In Canadian health facilities, the requirement is not a floor plan — it is a set of separations, flows and pressures that the plan has to deliver. Public Health Ontario's provincial guidance requires clear separations between soiled and clean areas, with decontamination work areas physically separated from clean and other work areas by walls or partitions, and with the soiled work area physically separated from all other areas of the space. Ventilation, temperature, humidity and water quality are all specified as well, because the separation is only as good as the airflow that supports it.
The layout decision is usually forced by the equipment a facility already owns: a CliniEco 6 L benchtop ultrasonic cleaner with dual-frequency operation or a pass-through washer-disinfector each imposes its own physical footprint and its own side of the dirty-to-clean line. This article sets out what each zone must do and contain, the ventilation figures that apply to each, the minimum obligations when only one room is available, and how the Canadian position differs from the United States baseline.
What do Canadian requirements actually say about zoning?
The operative document for Ontario is the provincial guidance for cleaning, disinfection and sterilization in all health care settings (3rd edition, May 2013), published by Public Health Ontario with the Provincial Infectious Diseases Advisory Committee. Its Appendix C — Recommendations for Physical Space for Reprocessing — is the section that decides zoning questions, and it is organised into personnel, space and environment requirements rather than into a floor plan.
The core space requirement is stated as a list of separations:
- There must be clear separations between soiled and clean areas.
- Decontamination work areas should be physically separated from clean and other work areas by walls or partitions to control traffic flow and to contain contaminants generated during decontamination.
- Soiled work areas must be physically separated from all other areas of the space.
- Walls or partitions should be constructed of materials capable of withstanding frequent cleaning with the products used in the setting.
- Doors to all work areas should be kept closed at all times, with self-closing doors recommended to restrict access and optimise ventilation control.
- In healthcare facilities, doors should be pass-through, to ensure one-way movement by staff from contaminated areas to clean areas.
Several of those items carry a CSA cross-reference in the guidance — the space and ventilation requirements are attributed to the CSA Z314 series, the family of Canadian standards for decontamination and sterilization of reusable medical devices. The distinction matters when a facility is asked "which rule applies to us": the provincial guidance sets the duty, and the CSA standards supply the facility, ventilation and water-quality numbers the duty is measured against.
There is also a siting rule that catches people out. Decontamination and sterilization areas must meet the processing-space requirements and must not be located in the operative procedure room, nor near a potential source of contamination such as sinks, hoppers, linen or trash disposal areas. A "sterile room" that shares a wall with a slop hopper is not compliant however well it is finished.
How is each zone defined, and what separates them?
The reprocessing area is normally described as four functional zones moving in one direction. The table below sets out what each zone does, what crosses its boundary, and the pressure relationship the guidance expects.
| Zone | Activity | Boundary control | Pressure and airflow | Typical content |
|---|---|---|---|---|
| Receiving and decontamination (soiled) | Receiving, sorting, manual cleaning, ultrasonic cleaning, washer loading | Physically separated from all other areas by walls or partitions; restricted access; doors closed | Negative pressure; minimum 8 air changes per hour; minimum 2 outdoor air changes per hour | Decontamination sinks, ultrasonic unit, washer-disinfector loading side, PPE station |
| Inspection, assembly and packaging (clean) | Drying, inspection, function testing, pouching or wrapping, sealing | Separated from the soiled area; no return path to soiled | Positive pressure; minimum 10 air changes per hour; minimum 3 outdoor air changes per hour | Clean benches, light and magnification, heat sealer, indicators, packaging stock |
| Sterilization | Loading and running sterilizer cycles | Adjacent to but distinct from the clean assembly area | Positive pressure (sterilizer equipment room); exhaust not recirculated | Sterilizers, utility connections, load records |
| Sterile storage | Storing processed packs until use | Separated from soiled activity; clean supplies and PPE stored apart from soiled items | Monitored humidity; independent humidity monitor recommended | Shelving, dated and rotated stock, case carts |
Two figures in that table do the real work in an inspection. First, the pressure relationship: soiled areas are held at negative pressure and clean areas at positive pressure, so air moves from clean to soiled rather than the reverse. Second, exhaust air from the department is vented outdoors and not recirculated, and portable fans are not to be used in any area of the sterile processing department — a pedestal fan moves contaminated air across exactly the boundary the walls were built to create.
What are the minimum obligations when a facility only has one room?
Small clinics and satellite sites frequently have one room available for reprocessing. The guidance does not license a single undivided space; it sets a minimum set of obligations that a single room must still satisfy. The table below separates what a two-room arrangement gives a facility from what has to be engineered into a single room instead.
| Obligation | Two-room (separate soiled and clean rooms) | Single room (minimum to satisfy) |
|---|---|---|
| Separation of soiled from clean work | Provided by the wall between rooms | Physically separated soiled work area within the room, plus a defined no-return line; walls or partitions used where the separation is not structural |
| Direction of travel for staff and instruments | Enforced by the room sequence | A written one-way rule from the soiled bench to the clean bench, with the soiled bench placed furthest from the exit used for clean work |
| Door control | Doors kept closed; pass-through doors recommended where the door joins the two rooms | Doors to the work area kept closed at all times; self-closing hardware recommended |
| Access control | Decontamination access restricted to authorised personnel | The same restriction applies to the decontamination part of the room |
| PPE donning and removal | An area provided for donning or removing PPE; where staff interchange between clean and contaminated areas, PPE is carefully removed and hands thoroughly washed | A defined PPE station at the soiled end, with hand hygiene between the two sides |
| Hand hygiene | Dedicated hand washing sinks at or near decontamination and preparation areas and at entrances to and exits from the decontamination area; sinks not used for other purposes | Dedicated hand washing sink(s) serving the soiled side, placed so that the clean bench is not reached before the sink |
| Clean supplies and PPE storage | Stored in an area separate from soiled items and cleaning processes | The same separation inside the room: clean stock stored away from the soiled bench, never on it |
| Ventilation | Zones can be separately pressured | Single-room airflow still has to keep contaminants at the soiled end; separation by local exhaust or an enclosure is preferable to relying on distance alone |
| Water quality | Applied to the processing area | The same limits apply to the water used in the room, including the final rinse |
Read that table as an answer to the question "can we do this in one room?" The answer is yes, provided the facility can show separation, one-way movement, access control, PPE control, hand hygiene, storage separation and adequate ventilation. What a single room cannot do is remove the requirement for those things. A bench with a laminated "soiled" sign is not a separation; a physical break that instruments and staff do not cross is. The part of the arrangement a plan will not show is the chemistry and the verification behind it: an enzyme ultrasonic cleaning solution supplied as a 4 L concentrate and a documented rinse step are what make the soiled end of the room do its job.
There is one more obligation that applies to the room regardless of size: reprocessing spaces must not sit in the procedure room, and must not sit next to sinks, hoppers, linen storage or waste handling. If the only free space in a clinic is beside the utility sink and the waste bin, that space does not meet the requirement no matter how the bench is laid out.
What should inspections see in the numbers?
The environment requirements are numeric, which makes them checkable, and that is why they are worth writing into a facility's own documentation before anyone asks.
- Ventilation. Minimum 8 air changes per hour for soiled areas and 10 for clean areas, with minimum 2 and 3 outdoor air changes per hour respectively. Soiled areas negative, clean areas positive, exhaust vented outdoors and not recirculated, and no portable fans anywhere in the department.
- Temperature. Decontamination work areas in the range of 18–20 °C, and clean areas in the range of 20–23 °C.
- Relative humidity. Maintained between 30 and 60 per cent, preferably 40–50 per cent, and monitored daily. An independently calibrated humidity monitor is recommended in each sterile storage area, because humidity above about 70 per cent can compromise sterile packaging.
- Water quality. Water used in the processing area should appear colourless, clean and without sediment, with limiting values including pH 6.5–8, evaporation residue at or below 15 mg/L, conductivity at or below 50 µS/cm, hardness at or below 0.1 mmol/L, chloride at or below 3 mg/L and iron at or below 0.2 mg/L.
Where the humidity in a sterile storage area rises to the point that packages become damp, the guidance's response is specific: notify facility management, move as much inventory out of the area as is practical, and repackage and reprocess any item that is visibly damp or damaged — and if the item is single-use, discard it. The layout question and the storage question are the same question at that point.
How does the Canadian position compare with the United States?
The comparison is useful because the two systems reach similar conclusions through different documents. The CDC's guideline for disinfection and sterilization in healthcare facilities (2008, updated June 2024) states that the central processing area should ideally be divided into at least three areas — decontamination, packaging, and sterilization and storage — with physical barriers separating the decontamination area from the other sections to contain contamination on used items. So far, that is the same architecture.
The numbers then diverge, and the divergence is worth knowing rather than smoothing over. The CDC guideline reports that the American Institute of Architects recommends negative pressure and no fewer than six air changes per hour in the decontamination area, while the Association for the Advancement of Medical Instrumentation recommends 10 air changes per hour, and 10 air changes per hour with positive pressure in the sterilizer equipment room. The Ontario guidance, working from the CSA standards, specifies 8 air changes per hour for soiled areas and 10 for clean areas. A facility citing a US figure in a Canadian inspection is citing the wrong baseline, even where the intent is identical.
The other structural difference is what the documents are. In Canada the practical, inspection-facing duty comes from provincial guidance and provincial instruments, with the CSA Z314 series supplying the engineering numbers and ISO 15883 covering washer-disinfectors as machines and ISO 17664 covering the manufacturer's reprocessing instructions for the instruments themselves. In the United States the equivalent engineering baseline sits with AAMI ST79 and the AIA guidance. None of these are interchangeable, and a facility operating in one jurisdiction cannot substitute the other's numbers.
How does a facility evidence its layout?
The layout is only half the requirement; the other half is being able to show it. Three artefacts carry most of the weight:
- The reprocessing-area policy, describing the zones, the direction of travel, which door is used for what, and where PPE is donned and removed.
- The ventilation and environment record — the commissioned figures for the space, and the daily humidity and temperature readings that show the space is still performing as commissioned.
- The hand-hygiene and PPE rules at the boundary, written down and reinforced, because a well-built separation that staff walk around is not a separation.
In a single-room arrangement the policy is doing more of the work, which is exactly why it has to be specific. "We clean instruments at one end of the room" is not evidence of a separation; a documented one-way flow with a fixed soiled bench, a fixed clean bench, and no staff or instrument movement crossing back is.
Sources
- Public Health Ontario / PIDAC — Cleaning, Disinfection and Sterilization in All Health Care Settings, 3rd edition (May 2013), Appendix C and endoscope physical-space section
- Ontario Ministry of the Environment, Conservation and Parks — Guideline C-4: The management of biomedical waste in Ontario
- Ontario Regulation 347 — General – Waste Management (Environmental Protection Act)
- Ontario Regulation 67/93 — Health Care and Residential Facilities (Occupational Health and Safety Act)
- Royal College of Dental Surgeons of Ontario — Infection Prevention and Control standard
- Royal College of Dental Surgeons of Ontario — Standard of Practice: Infection Prevention and Control in the Dental Office, v3
- CDC — Guideline for Disinfection and Sterilization in Healthcare Facilities (2008, updated June 2024)
- CSA Group — Effective sterilization in health care facilities by the steam process (CSA Z314.3)
- ISO — ISO 11607-1, packaging for terminally sterilized medical devices
- Canadian Centre for Occupational Health and Safety — occupational health and safety resources
- Health Canada — Reprocessing of N95 respirators notice (Open Government dataset record)
- CliniEco Medical — sterilization monitoring collection
Put the paperwork side with the layout
- Take the record sheet with you. The sterilization record centre carries a printable blank log sheet and a load-log generator, arranged as four record groups that line up with the RCDSO IPAC self-audit form, and it runs in the browser without an account.
- Check your own space before a surveyor does. The same page includes a self-check you can run against your current layout and monitoring routines, so a facility can see where the soiled and clean sides actually meet in practice.
- Have a question about your own facility? Send it in and you will get a written answer specific to your setup, with the regulation or standard it is based on cited. Ask your compliance question.
- Ordering for a clinic, a lab or a care home? Wholesale and multi-site ordering covers case pricing and account setup, and the B2B wholesale collection lists the lines stocked for institutional buyers.
- become a distributor
Related reading
- Sterilization area workflow: clean and dirty zones
- Ultrasonic cleaning step: solution or rinse
- Autoclave water quality and sterilization failures
- Reprocessing workflow for dental offices: washing, packaging, sterilizing and storing
Frequently Asked Questions
Can a clinic do all reprocessing in a single room?
Yes, provided the room still delivers the required separations: a physically separated soiled work area, a defined one-way path from soiled to clean, restricted access, closed doors, a PPE station, dedicated hand-washing facilities, storage separated from soiled activity, and ventilation that keeps contamination at the soiled end. What a single room cannot do is exempt the facility from any of those obligations.
Do the Canadian figures match the American ones?
No, and the difference is easiest to see in the ventilation numbers. The Ontario guidance, working from the CSA standards, specifies 8 air changes per hour for soiled areas and 10 for clean areas with soiled areas under negative pressure. The CDC guideline records six air changes per hour recommended by the American Institute of Architects and 10 recommended by AAMI for the decontamination area under negative pressure. Citing the wrong baseline in the wrong jurisdiction is a documentation error even when the intent is the same.
Where should the decontamination area be located?
It must meet the processing-space requirements and must not be located in the operative procedure room, or near a potential source of contamination such as sinks, hoppers, linen storage or trash disposal. Putting the decontamination bench beside the room's hopper fails on siting rather than on equipment.
Why does the direction of airflow matter so much?
Because a separation that relies on walls alone still leaks if the pressure is reversed. The guidance requires negative pressure in soiled areas and positive pressure in clean areas, exhaust vented outdoors and not recirculated, and no portable fans anywhere in the sterile processing department. Those three conditions together keep air moving from clean toward soiled rather than the other way.
Does a pass-through door actually change anything?
It converts a rule into a physical constraint. In healthcare facilities the guidance recommends pass-through doors between contaminated and clean areas precisely to make one-way movement automatic instead of something staff have to remember. Where that is not achievable — and in many small clinics it is not — the equivalent control is a documented one-way flow plus a sink and PPE change at the boundary.
What has to be monitored after the layout is built?
Temperature, humidity and the environment record for the space, with relative humidity maintained between 30 and 60 per cent and monitored daily, plus the practice-level records that show the layout is being used as designed: hand hygiene at the boundary, PPE removal, and cleaning of work surfaces. The rebuild is a one-time event; the record is what shows it is still working.
CliniEco Medical supplies sterilization monitoring and reprocessing consumables in Canada. MDEL #35334.