A lab consumable is bought twice: once as a size on a shelf and once as a case on an order. The two numbers are rarely the same, and the gap between them is where stockouts and over-ordering both come from. A case of specimen containers is not one hundred units, a case of petri dishes is not a sleeve, and a box of swabs is not a case of swabs.
This article sets out the sizes, the specifications and the case units that Canadian clinics and small laboratories order most often, with the standard or the federal rule that fixes each one. Three lines cover most of the bench: the 90 mL graduated specimen cups as a case of six hundred, the 100 × 15 mm sterile petri dishes at three hundred and twenty to a case, and the 15 mL sterile centrifuge tubes at five hundred to a case.
What counts as a lab consumable when a Canadian clinic orders by the case?
It is a device, not a supply cupboard item, and the federal classification rule decides what kind. Specimen containers, tubes, dishes and pipettes are non-invasive devices that hold a specimen rather than enter the body, so they fall to the residual rule: Rule 7(1) of Schedule 1 to the Medical Devices Regulations classifies all other non-invasive devices as Class I.
Class I still carries obligations. Section 21(1) requires a label that sets out the information listed there, and section 23(1) sets the language floor at either English or French for a device sold into professional channels. A Class I device does not need a manufacturer licence under section 26, which is why a clinic can buy containers from several suppliers without checking a licence number, but the label obligation does not disappear with the licence requirement.
The practical consequence for ordering is that a consumable's specification has to be checked against a published standard rather than against a supplier's description. Health Canada's medical devices portal is where the classification rules and the labelling guidance sit.
Which sizes and case units do Canadian clinics actually order?
The table below is the ordering side of the same products, with the case unit as the primary number because that is the number a purchase order needs.
| Item | Size and specification | Case unit | What the case size decides |
|---|---|---|---|
| Graduated specimen cup | 90 mL, graduated, leak-proof screw cap | 6 × 100-pack = 600 cups | Bench-weeks per case; a 20-cup day is 30 working days |
| Sterile specimen container | 120 mL, sterile, screw cap, tamper-evident | 2 × 100-pack = 200 containers | Sterile work only; the case is small because the use is selective |
| Sterile petri dish | 100 mm diameter × 15 mm height, polystyrene, vented | 320 dishes to a case | Plating days; a 30-plate day is about 11 working days |
| Centrifuge tube, 15 mL | Sterile, graduated, screw cap | 500 tubes to a case | Draw and aliquot volume; the tube is the unit of work, not the case |
| Centrifuge tube, 50 mL | Sterile, graduated, screw cap | 500 tubes to a case | Same count as 15 mL, different bench use |
| Serological pipette and sealing film | Pipette sizes by volume range, film by roll | Single SKU, mixed pack | Two consumables that are always opened together |
| Cotton swab, double tipped | 6 inch, double tipped | 13 × 100-pack = 1,300 swabs | Swab-heavy benches; a 60-swab day is about 21 working days |
| Specimen transport bag, 3-wall | 6 × 9 inch, document pouch, absorbent pad | 10-box case = 1,000 bags | Courier volume; a 40-bag day is 25 working days |
Two of those rows carry a trap. The specimen cup case is six boxes, not one, so a clinic that orders "one case" receives six hundred cups and a clinic that orders "one box" receives one hundred. The transport bag case is ten boxes of one hundred. Neither number is wrong; they answer different questions, and the purchase order has to say which one it means.
How do case units work — pack, box, case and each?
Four words, four different quantities, and the same product can be described by all four. A pack is the sealed inner unit; a box is what the pack sits in; a case is the shipping carton; an each is one item on the bench. The federal labelling rule does not standardise those words, so the only reliable source is the specification sheet for that SKU.
| Unit | What it means in practice | Where the count is decided |
|---|---|---|
| Each | One item on the bench, one cup or one dish | Bench procedure, not the supplier |
| Pack | Sealed inner unit, often 100 for cups and containers | Manufacturer's packaging specification |
| Box | The carton holding one or more packs | Supplier's carton marking |
| Case | The shipping unit a clinic orders | Supplier's ordering unit, stated on the quotation |
The check that prevents most ordering errors is to ask for the case count in each, not in cases. A quotation that says "case of 6" without naming the units has left the important number out, and a receiving clerk who counts six boxes instead of six hundred cups will file a short shipment that is not short.
Does Canada classify these consumables the same way as the United States?
No, and the difference is easier to see at the level of the record than at the level of the product. Both countries treat a specimen container as a low-risk device, but Canada reaches that result through a classification rule applied by the manufacturer, while the United States files the device under a specific product code and regulation.
| Item | Canada | United States |
|---|---|---|
| Classification route | Schedule 1 Rule 7(1): other non-invasive devices are Class I | Product-code assignment in the FDA classification database, for example 21 CFR 864.3250 for specimen containers |
| Premarket requirement | No manufacturer licence for Class I | Listed as exempt from premarket notification for that code |
| Label obligation | Section 21(1) content, section 23(1) language floor | Labelling requirements attached to the device type, with English |
| Sterile container | Class I under the same rule, with the sterility claim on the label | Product code FMH, sterile container, listed as Class I |
| Non-sterile container | Class I, no sterility claim permitted | Product code NNI, non-sterile container, listed as Class I |
The distinction between a sterile and a non-sterile container is not a marketing difference in either country. It is two product codes in the United States and two claims in Canada, and a case that arrives with a sterile label on a non-sterile carton is a labelling error that a receiving check can catch.
Which standards sit behind the size printed on the label?
Sizes come from documents, and a few of them matter more than the rest on a clinic bench.
ISO 6710:2017 is the standard for single-use containers for venous blood specimen collection, and it is the reason blood tubes are described by draw volume and additive rather than by "small" and "large". ISO 15189:2022 is the medical laboratory quality standard, and it is what makes the consumable a controlled item rather than a commodity: the laboratory has to show that the container it uses is fit for the examination it performs. For anything supplied sterile, ISO 11607-1:2019 governs the packaging system that holds the claim.
| Document | What it fixes | Where it shows up on a clinic order |
|---|---|---|
| ISO 6710:2017 | Single-use containers for venous blood collection | Tube draw volume and additive description |
| ISO 15189:2022 | Laboratory quality management, including selection of consumables | The laboratory's own specification list |
| ISO 11607-1:2019 | Packaging for terminally sterilised devices | The sterile claim on a dish or container |
| Schedule 1 Rule 7(1) | Class I status of a non-invasive device | No licence number to check, label content still required |
How do you convert bench workload into cases per month?
Divide the daily count by the case count and multiply by working days. The arithmetic is trivial and the inputs are not, which is why the table below is written as a worked example rather than as a benchmark.
| Bench | Daily count | Case count | Working days per case |
|---|---|---|---|
| Urine microscopy | 20 cups | 600 | 30 |
| Plating | 30 dishes | 320 | 11 |
| Draw and aliquot | 40 tubes | 500 | 12 |
| Swab bench | 60 swabs | 1,300 | 21 |
| Courier dispatch | 40 bags | 1,000 | 25 |
Two adjustments belong in the calculation. A sterile item used only for a subset of work consumes at a fraction of the bench rate, which is why the sterile container case is two hundred rather than six hundred: the smaller case exists so a clinic does not carry a year of sterile stock that expires before it is used. And a consumable that is opened in pairs, such as a pipette with its sealing film, consumes two lines at once and should be counted as one order line with two SKUs.
The clinical laboratory standards published by CLSI are the usual reference for the procedural assumptions behind those counts, and the CDC standard precautions guidance covers the handling side that decides when a glove or a fresh container is required.
Is a consumable ordered by the case the same thing in Canada as in the United States?
The product is the same and the ordering vocabulary is not. American catalogues habitually quote a case as a count of inner boxes, and Canadian suppliers quote both, so a buyer comparing two quotations can be comparing a case of five hundred against a case of fifty.
| Item | Canada | United States |
|---|---|---|
| Case description | Usually the shipping carton, with the inner pack count stated | Often the count of inner boxes, with the unit count stated separately |
| Unit of measure on a quotation | Case, box, pack, each | Case, box, pack, each |
| Regulatory anchor for the size claim | Section 21(1) label content | Device-type labelling in Title 21 |
| Sterile claim | Manufacturer's declaration against ISO 11607-1:2019 | Premarket submission and labelling for the code |
The safe habit on either side of the border is the same: ask for the unit count in each, in writing, on the quotation.
What should the purchase order state?
Six lines keep a consumable order unambiguous. State the item and its size in metric units with the tolerance where one exists. State the material where it changes performance, as polystyrene does for a dish and polypropylene does for a tube. State sterility as a claim rather than an adjective. State the case unit in each. State the standard and edition year where the product is described by one. And state the storage condition if the product has one, because section 21(1)(j) puts special storage conditions on the label and a clinic that stores a case outside them has broken the condition the manufacturer set.
References
- Medical Devices Regulations, SOR/98-282, Schedule 1 Rule 7, sections 21 and 23 — laws-lois.justice.gc.ca (checked 11 November 2026)
- Medical devices portal — canada.ca (checked 11 November 2026)
- ISO 6710:2017, single-use containers for venous blood specimen collection — genorma.com (checked 11 November 2026)
- ISO 15189:2022, medical laboratories, requirements for quality and competence — genorma.com (checked 11 November 2026)
- ISO 11607-1:2019, packaging for terminally sterilized devices — genorma.com (checked 11 November 2026)
- 21 CFR 864.3250, specimen container — law.cornell.edu (checked 11 November 2026)
- FDA product classification database — accessdata.fda.gov (checked 11 November 2026)
- Device classification API, specimen container codes FMH and NNI — open.fda.gov (queried 11 November 2026)
- 21 CFR part 801, labelling — ecfr.gov (checked 11 November 2026)
- CLSI standards catalogue — clsi.org (checked 11 November 2026)
- Standard precautions for healthcare — cdc.gov (checked 11 November 2026)
- Routine practices and additional precautions — publichealthontario.ca (checked 11 November 2026)
- Biological hazards — ccohs.ca (checked 11 November 2026)
- Infection prevention and control — who.int (checked 11 November 2026)
- Laboratory and Specimen Collection Centre Licensing Act, section 9 — ontario.ca (checked 11 November 2026)
- Act respecting medical laboratories, chapter L-0.2, section 31 — legisquebec.gouv.qc.ca (checked 11 November 2026)
- Charter of the French language, chapter C-11, section 51 — legisquebec.gouv.qc.ca (checked 11 November 2026)
- Autorité des marchés publics — amp.quebec (checked 11 November 2026)
- Institute for Quality Management in Healthcare — iqmh.org (checked 11 November 2026)
- R.R.O. 1990, Reg. 682, Laboratories, section 14 — ontario.ca (checked 11 November 2026)
Related reading
- Lab consumables: sizes, specs and case units for Ontario clinics
- Lab consumables: sizes, specs and case units for Quebec clinics
- Specimen containers 90 mL vs 120 mL: which does a Canadian lab stock?
- Centrifuge tubes 15 mL vs 50 mL: stocking a clinic laboratory
- Unit of measure traps: case, box, pack and each in medical consumable pricing
Frequently asked questions
What counts as a lab consumable in Canada?
A specimen container, tube, dish, pipette or film is a non-invasive medical device that holds a specimen rather than entering the body. Under Rule 7(1) of Schedule 1 to the Medical Devices Regulations, other non-invasive devices are Class I, so no manufacturer licence is required, but the label content in section 21(1) and the language floor in section 23(1) still apply.
How many cups are in a case of 90 mL specimen cups?
Six hundred. The case is six packs of one hundred, so a purchase order that says "one case" receives six hundred cups and an order that says "one box" receives one hundred. The two numbers answer different questions and both belong on the quotation.
How many petri dishes are in a case?
Three hundred and twenty for a 100 × 15 mm sterile polystyrene dish. A bench that plates thirty dishes a day uses a case in about eleven working days, which is the number to plan against rather than the case price.
Is the case unit the same in Canada and the United States?
Not always. American catalogues often quote a case as a count of inner boxes and state the unit count separately, while Canadian quotations usually describe the shipping carton. Ask for the unit count in each on the quotation, in writing, before comparing two prices.
Which standard fixes the size of a blood collection tube?
ISO 6710:2017 covers single-use containers for venous blood specimen collection, which is why tubes are specified by draw volume and additive rather than by size class. For the laboratory side, ISO 15189:2022 requires the laboratory to show that the containers it uses are fit for the examinations it performs.
Does a specimen container need a device licence in Canada?
No. A specimen container is a Class I non-invasive device under Rule 7(1), and the licence requirement in section 26 applies to Class II, III and IV devices. The container still needs the label content required by section 21(1) and, where the product is sold as sterile, a sterility claim that the packaging supports.
Turning the case count into a standing order
The compliance log centre carries the printable logs that keep a bench count and a consumable count on the same sheet, and the supply planner on that page converts a daily count into cases per month. For a standing order across several sites, the route is the institutional account enquiry page; where the laboratory also runs an in-house sterilizer and the consumable file has to sit with the reprocessing records, the sterilization compliance consultation covers that side. Reselling? become a distributor.
CliniEco Medical distributes clinic consumables in Canada under MDEL #35334. This article describes sizes and case units published by the manufacturers of the products named and requirements published by Health Canada and the United States federal register; the specification that binds a specific order remains the one on the manufacturer's current specification sheet and on the clinic's own written procedure.
Last updated: 11 November 2026.