The question a hospice usually asks is whether its sterilizer needs an annual validation. The answer the Canadian guidance gives is that validation is triggered by events rather than by the calendar: it happens at installation, it is repeated when something changes, and it is supported every day the unit is used by monitoring that is a different obligation with a different record.
This page separates the three obligations, sets out what installation validation requires, which events force a re-run, what the daily monitoring consists of, how the standards are numbered and dated, and where Canadian and American requirements diverge. The consumables involved are the 24-hour self-contained biological indicator, the dry-block incubator that reads the test, and the Bowie-Dick test pack used for the daily air removal check on a pre-vacuum unit.
Quick facts on sterilizer validation in a Canadian hospice
- Installation requires at least three consecutive cycles with biological and chemical challenges in an empty chamber, plus at least one cycle with a full test load.
- A dynamic air removal sterilizer also needs three consecutive air removal tests in an empty chamber at installation.
- Requalification is triggered by major repair, construction or relocation, unexplained sterility failures and changes to the steam supply.
- Routine monitoring is separate: a biological indicator each day the sterilizer is used, and with each cycle type used that day.
- Reviewing the written procedure is an annual obligation, which is not the same thing as an annual validation.
- A sterilizer that is moved between rooms has been relocated, and relocation is a requalification trigger rather than a housekeeping task.
What is the difference between validation and routine monitoring?
Validation is the evidence that the process can do what it claims, established before it is used and re-established after anything that could have changed it. Routine monitoring is the daily evidence that it is still doing it. A hospice that runs daily spore tests and has never documented an installation test has monitoring without validation; a hospice with an installation report from a decade ago and no daily results has validation without monitoring. Inspectors find the second one first, because the gap is visible in a single folder.
| Obligation | When it happens | What it produces |
|---|---|---|
| Installation and commissioning | Before routine use, on a new, donated or relocated unit | Consecutive challenge cycles, air removal tests, a signed record |
| Routine monitoring | Every day the sterilizer is used | Physical printout, biological result, chemical indicator result |
| Requalification | After a named event, not on a date | A repeat of the installation logic with a test load |
| Procedure review | At least annually | A dated, reviewed policy that matches current practice |
| Staff competency | At defined intervals, documented | Training and competency records for everyone who runs the unit |
What does installation validation require in Ontario?
The provincial reprocessing standard sets out a sequence a hospice can hand to the installer. The sterilizer is installed according to the manufacturer's instructions. Following installation it must pass at least three consecutive cycles with the appropriate challenges, biological and chemical, placed in an empty sterilizer, as well as at least one cycle challenged with a full test load, before it goes into routine service. For a dynamic air removal unit, three consecutive air removal tests are run in an empty sterilizer with an air detection test pack. The standard is also blunt about the outcome: a sterilizer is not approved for use if the biological indicator yields a positive result on any of those tests.
The same section recommends tabletop steam sterilizers for office settings, which is the category most hospice units fall into. That recommendation does not lower the installation requirements; it explains why they exist. A benchtop unit in a converted utility room has the same obligation as a hospital sterilizer, and the record is the only thing that distinguishes a hospice that met it from one that plugged the unit in and started running loads.
| Test | Condition | Pass criterion |
|---|---|---|
| Biological challenge cycles | Three consecutive cycles, empty chamber, indicator in a process challenge device | All three negative |
| Chemical challenge | Same three cycles, internal indicator in the challenge pack | All three show a complete change |
| Full test load | At least one cycle with a representative full load | Indicators acceptable and load conditions verified |
| Air removal test, pre-vacuum | Three consecutive tests, empty chamber, Class 2 indicator pack | All three pass per the pack instructions |
Which events force a re-run of the validation?
The standard lists them, and the list is short enough to paste into a policy: after major repairs to an existing sterilizer; when there has been construction, relocation or other environmental change in the area; after unexplained sterility failures; after changes in steam supply or delivery; and after repairs or modification to the emission control system. Each is a documented event with a test load attached rather than a judgement call.
Two of them catch hospices that share a building. Construction in an adjacent suite disturbs dust and airflow, and the standard treats environmental change as a trigger in its own right. A building steam system that is serviced, re-piped or switched to a different boiler is a change in steam supply or delivery. Neither event looks like a sterilizer problem at the time, and both invalidate the assumption behind every routine result that follows.
| Event | Who usually notices | Evidence the file needs |
|---|---|---|
| Major repair | Service technician | Repair report, test load run, indicator results |
| Construction or relocation | Facilities or the unit manager | Date of the change, requalification record |
| Unexplained sterility failure | Whoever reads the biological result | Investigation note, repeat result, release decision |
| Steam supply change | Building operator | Description of the change, requalification record |
| Emission control repair | Service technician | Repair report and re-test |
Does a sterilizer that is barely used still need validation and monitoring?
Yes, and the obligation follows use rather than volume. Validation is a property of the installation, so a unit that runs twice a month keeps its validation until an event invalidates it. Monitoring follows the days it is used: a unit that runs on two days in a month needs two biological results for that month, not none, and not a monthly test that stands in for both.
The pattern that causes trouble in a low-volume hospice is the long gap. A unit that has not run for six weeks has had no monitoring during that time, and the first load after the gap is being released on evidence from before the idle period. The workable policy is that the first load after an extended idle period gets the full daily monitoring set and is not released until the biological result is available, which in practice means running the test on the first day rather than on the third.
How do Canada and the United States differ on validation and monitoring frequency?
Canada places the frequency in provincial guidance with named triggers; the United States places a weekly monitoring floor in national guidance and leaves validation to the manufacturer's instructions, the accreditation standard and facility policy. The two systems are compatible, but they are not the same document, and a hospice group operating on both sides of the border writes two procedures.
| Item | Canada (Ontario guidance) | United States (CDC guidance) |
|---|---|---|
| Biological monitoring frequency | Each day the sterilizer is used, and each cycle type used that day | At least weekly, with daily described as earlier detection on a heavily used unit |
| Acceptance testing at installation | Three consecutive challenge cycles plus a full test load, documented | Follow the manufacturer's instructions and the accreditation standard |
| Requalification triggers | Named events in the provincial standard | Not set out as a national list; policy and service requirements apply |
| Air removal test | Every day the unit is used, Class 2 indicator | Recommended each day the sterilizer is used |
| Procedure review | At least annually, with infection control review | Policy review cycle set by the facility |
| Hospice oversight | Provincial health authority and accreditation | 42 CFR 418.60 condition of participation plus state survey |
Do Canada and the United States differ on what counts as a validated cycle? Only in paperwork. Both expect the sterilizer to be challenged with a resistant organism under the conditions the load will actually present, and both expect the manufacturer's instructions to govern the parameters. The Canadian system writes the challenge count and the trigger events down, which makes the file a checklist rather than an argument.
Which standards sit behind the tests?
Four families, and the numbering matters because revisions are recent. Moist heat sterilization validation is covered by ISO 17665:2024, which consolidated and replaced the part-numbered 2006 standard and its technical specifications. Biological indicators are covered by ISO 11138-1:2017 for general requirements and ISO 11138-3:2017 for moist heat processes. Chemical indicators are covered by ISO 11140-1:2014, which defines the classes including the Class 2 indicator used in an air removal test and the Class 5 integrating indicator used for load release. Packaging is covered by ISO 11607-1:2019, and the manufacturer's processing instructions by ISO 17664-1:2021.
In Canada the provincial and national reprocessing standards sit above those: CSA Z314:23 covers reprocessing of medical devices in all health care settings, and the provincial standard repeats its requirements in local language. A hospice SOP that cites the 2006 validation standard is not wrong about the method; it is citing a document that has been superseded, which is the kind of finding that costs a day of rewriting during an inspection.
How do Canada and the United States differ on the validation file?
Five documents kept together: the manufacturer's installation and operating instructions for the model, the installation and acceptance record with the challenge cycles and results, the maintenance and repair history, the requalification records for every trigger event, and the current written procedure with its review date. The daily monitoring results go into the same file or a referenced one, because they are the evidence the validation is defending.
Retention follows the pattern used elsewhere in the setting. The provincial standard asks for records to be kept according to facility policy, and the reference most clinical settings borrow in Ontario is Ontario Regulation 114/94, which sets a ten-year period for clinical records. A validation file kept for two years cannot answer a question about a load that was released five years ago.
An American hospice assembles the same five documents, and where they come from is different: the acceptance record follows the manufacturer's instructions and the accreditation standard rather than a provincial challenge count, and the oversight hook is the infection control condition of participation at 42 CFR 418.60 with HIPAA retention at 45 CFR 164.316. The Canadian file has more prescribed content and fewer places to look for the answer.
What is different about validation in a hospice?
Three things. A donated or inherited sterilizer often arrives with no installation record at all, and the first thing the hospice owns is a unit whose validation status is unknown — which means the installation logic is run once, on the hospice's account, before any patient load. A shared building means construction, steam changes and plant work happen without the hospice being told, so the trigger list has to be in the facilities contract rather than in a procedure nobody outside the unit reads. And a contracted reprocessing arrangement means the validation being relied on belongs to another organisation, so the hospice needs the acceptance record, the current monitoring results and the requalification history in writing rather than as an assurance.
None of those are regulatory novelties; they are the same three obligations meeting a small organisation. The hospices that handle them well do one thing differently: they name an owner for the sterilizer file, with a deputy, so that the question of when the unit was last validated has an answer that does not depend on who is on shift.
Where does a hospice take this next?
Three things a hospice can act on rather than read: a printable compliance log sheet that records the cycle, the challenge, the result and the release signature and exports from the browser; the sterilization log generator on the same page, which builds a month of records from the cycle schedule; and, where a validation question has to be answered for an inspector, an accreditor or a service contract, Ask a Compliance Specialist, which cites the standard or regulation the answer rests on.
Hospices ordering indicators, test packs and incubators across several sites can ask about the institutional account enquiry page for case quantities and account setup. Reselling? become a distributor.
Related reading
- How many biological indicators a Canadian clinic runs per sterilizer per week
- Traceability records for every sterilized load
- Sterilization requirements across Ontario, Alberta and British Columbia compared with CMS
- Pouch sealer and impulse sealer validation
- Infection control log: what to record and how long to keep it
Sources and version notes
- Public Health Ontario, provincial reprocessing standard for cleaning, disinfection and sterilization in all health care settings, 3rd edition 2013 — checked 17 November 2026.
- Public Health Ontario, infection prevention and control for clinical office practice, 2nd revision November 2026 — checked 17 November 2026.
- CDC, sterilizing practices, monitoring and quality control — checked 17 November 2026.
- CDC, sterilization of critical and semi-critical items — checked 17 November 2026.
- ISO 17665:2024, moist heat sterilization, development, validation and routine control — checked 17 November 2026.
- ISO 11138-1:2017, biological indicators, general requirements — checked 17 November 2026.
- ISO 11138-3:2017, biological indicators for moist heat sterilization processes — checked 17 November 2026.
- ISO 11140-1:2014, chemical indicators, general requirements — checked 17 November 2026.
- ISO 11607-1:2019, packaging for terminally sterilized medical devices — checked 17 November 2026.
- ISO 17664-1:2021, manufacturer information for processing of medical devices — checked 17 November 2026.
- CSA Z314:23, reprocessing of medical devices in all health care settings — checked 16 November 2026.
- 42 CFR 418.60, hospice condition of participation: infection control — checked 17 November 2026.
- Ontario Regulation 114/94, records under the Medicine Act, 1991 — checked 17 November 2026.
- Medical Devices Regulations, SOR/98-282, classification rules — checked 17 November 2026.
- Royal College of Dental Surgeons of Ontario, infection prevention and control standard of practice — checked 17 November 2026.
- Hospice Palliative Care Ontario — checked 17 November 2026.
- Accreditation Canada — checked 17 November 2026.
- Health Canada, medical devices in Canada — checked 17 November 2026.
- World Health Organization, decontamination and reprocessing of medical devices for health care facilities — checked 17 November 2026.
- openFDA device classification database — checked 17 November 2026.
- Occupational Safety and Health Administration, bloodborne pathogens — checked 17 November 2026.
- 21 CFR Part 880, general hospital and personal use devices — checked 17 November 2026.
Frequently Asked Questions
Is an annual sterilizer validation required in Canada?
Not as a calendar event. Validation is triggered by installation, major repair, construction or relocation, unexplained sterility failures and changes to the steam supply. What does happen at least annually is the review of the written procedure.
Does a donated or second-hand sterilizer need an installation record?
Yes. A unit whose validation status is unknown needs the installation logic run once before it is used for patient loads, which means the challenge cycles, the full test load and the air removal tests where the unit is a pre-vacuum type.
How many biological indicators are needed for a unit used two days a week?
One per day of use and one per cycle type used on that day. Two days of use means two results for that week, not a single weekly test standing in for both days.
Does moving a sterilizer to another room count as relocation?
Yes. Relocation is named as a requalification trigger, so the unit is revalidated after the move rather than returned to service on the basis that nothing mechanical changed.
Can a hospice rely on the hospital's validation for contracted reprocessing?
Only if the record is actually available. The acceptance record, the current monitoring results and the requalification history should be obtainable in writing, because the hospice is accountable for the instruments it receives back even when it did not process them.
What changes if the building's steam supply is serviced?
A change in steam supply or delivery is a named requalification trigger, so the sterilizer is revalidated after the work rather than assumed to be unaffected by it.
Regulations and standards are cited as published at the time of writing and are not reproduced in full. Provincial requirements differ and are revised, so confirm the version in force for your setting. This article is for information and is not legal advice. CliniEco Medical distributes medical consumables under MDEL #35334.