Check the sealer temperature at the start of the first shift that will use it, and again after any roll or paper change, after the unit is moved or serviced, and whenever a seal failure appears. That is the schedule that keeps a clinic out of trouble. A constant-heat sealer such as the CliniEco constant-heat pouch sealer holds a fixed platen temperature, so the reading drifts slowly and quietly — the failure it produces is a seal that looks complete and peels open three days later.
Every seal on a roll or pouch pack is made in your clinic. That single fact is why sealer verification belongs in the daily routine alongside the sterilizer checks, and why an inspector will ask for it. Here is a schedule that is practical for a two- to six-room clinic, and the records that make it defensible.
How often should a pouch sealer be temperature-checked?
At least once per shift start, and on every trigger event. The full list:
| Trigger | What to check | What to record |
|---|---|---|
| Start of the first shift using the sealer | Displayed or measured platen temperature against the setting the manufacturer specifies for your pouch material | Date, time, reading, operator initials |
| After a roll or paper change | Temperature still matches the specification for the new material and width | New material lot or width, reading |
| After the unit is moved, serviced or cleaned with a wet cloth | Temperature and dwell time; a displaced platen or moisture in the mechanism changes both | Reason for the check, reading, corrective action |
| Any seal failure, channel, wrinkle or open pack | Temperature, dwell, and whether the seal area was folded or the pack overfilled | Failure description, reading, product discarded or repacked |
| Periodic verification (commonly weekly to monthly, per the manual) | Compare the unit's reading with an independent reference where the manufacturer requires it | Reference device, reading, difference |
Where the sealer has a digital display and a lockout, the shift check takes under a minute. Where it has a dial and no digital readout, the check needs an external reference and should be written into the procedure with the method spelled out, because "we look at the dial" is not a verification.
Why is a per-shift check necessary if the temperature is fixed?
Because the failure mode is slow drift plus human variables. A constant-heat unit warms up to its set point and holds it, but the set point can move if the dial is nudged, if the unit was cleaned or moved, or if a different roll width now draws more heat out of the platen. Add the human side — a different operator with a different hand speed — and you have a process where two clinics using identical equipment produce different seal quality.
A per-shift reading catches the drift before a whole day's packs are formed. The alternative is discovering it in a week when packs start opening in the storage cupboard, by which time the affected loads must be reprocessed and the traceability question becomes urgent.
What does a good seal check actually test?
Temperature is only one of three variables. Dwell time and pressure matter just as much, and the usual in-house check is a physical seal inspection on a sample pack: a continuous seal width with no channel, wrinkle or gap, and a peel that requires deliberate effort rather than opening on its own. Where a clinic wants a defined method, a peel or dye penetration test on a sample pack gives a repeatable pass or fail instead of an opinion.
Whatever method is used, it should be written down on one page with the acceptance criteria, then applied by everyone who forms a pack. A procedure that exists only in the head of the most experienced staff member is not a procedure.
How should the records be kept?
The sealer check belongs on the same sheet as the sterilization cycle record, not in a separate maintenance file. That way, when a pack fails, the person investigating has the temperature reading, the cycle it went through and the operator for the same day in one place. Print a template, keep it at the bench, and file completed sheets with the monitoring records for the retention period your provincial rules set.
Two small habits make the log useful rather than decorative: write the reading as a number rather than a tick, and note the corrective action whenever the reading is out of specification — even if the action was simply to wait for the unit to reach temperature before resuming.
What if the sealer fails the check?
Stop sealing. Adjust the setting, wait for the unit to stabilise if it was cold, and re-check. Then inspect any packs formed since the last passing check: if the seal was made outside specification, the pack has to be treated as unverified and rewrapped in fresh packaging. That is a smaller job than it sounds, and far smaller than discovering it after storage.
If the unit will not hold its setting, take it out of service and record why. A sealer that "works if you press harder" is producing packs whose quality varies with the operator, which defeats the purpose of having a documented process at all.
Related reading
Frequently Asked Questions
How often should a pouch sealer be temperature-checked?
At the start of each shift that uses the sealer, and again after a roll change, after the unit is moved or serviced, and whenever a seal failure appears. Follow the manufacturer's manual for any additional periodic verification.
Do you need a calibrated thermometer to check a sealer?
Where the sealer has no digital readout, an external reference is needed to verify the setting. Check the manual for the method the manufacturer specifies, and record the reference used along with the reading.
What counts as a failed seal check?
A temperature outside the specification for your pouch material, a seal with a channel, wrinkle or gap, or a peel that opens without deliberate effort. Packs formed outside specification should be rewrapped and reprocessed.
Should sealer checks be kept with sterilization records?
Yes. Keeping them on the same sheet as the cycle record means a pack failure can be investigated from one page, and it keeps the whole reprocessing record in one file for retention.
CliniEco Medical is a licensed medical device establishment (MDEL #35334).
Use the sterilization log sheet generator to record sealer checks beside daily monitoring, and print the sealer check template for the bench. Setting up a packaging process from scratch? Ask a sterilization compliance specialist to review your sealer settings against the pouch material you buy.
Sterilization compliance hub · Sterilization pouch sealer calibration: how to verify temperature · Autoclave pouch seal failures: causes and how to fix them · Case review: a Mississauga clinic fixed recurring pouch seal failures
Ordering sealer, packaging and monitoring for a clinic or laboratory? Apply for the 24-hour biological indicator 25-pack, or open a wholesale and institutional supply account for case pricing on pouches, rolls, sealers and indicators. Reselling? become a distributor.