How are spirometry supplies and calibration documented in Canadian occupational health?

Roll of smooth white examination table paper

How are spirometry supplies and calibration documented in Canadian occupational health?

An occupational health clinic runs thirty lung function tests on a Tuesday. Each produces a trace read months later, and each depends on a device checked that morning against a three-litre syringe. The documentation question in Canada is rarely about the spirometer; it is whether the check, the operator and the consumables can be shown to a reviewer two years later.

Which tolerance does the 3-L syringe check have to meet?

The 2019 American Thoracic Society and European Respiratory Society technical statement is the reference most Canadian laboratories follow. Spirometric equipment must meet the performance requirements of ISO 26782, including a maximum permissible error of 2.5 percent when tested with a 3-L calibration syringe and the ISO 26782 test profiles. The statement also requires the syringe to hold an accuracy of plus or minus 0.015 L, or 0.5 percent of full scale.

Plenty of clinics still write "within 3.5 percent" on the log sheet, a looser tolerance carried over from earlier practice. Reading a 3-L syringe at 2.90 L is a 3.3 percent error: inside the old line, outside the current one. A reviewer who knows the standard will ask which figure was used.

What has to be checked daily, and what can wait for the month-end?

Blue nitrile examination gloves in a dispenser box

Daily work belongs to the syringe: inspect for displacement of the piston stop, and confirm it moves smoothly without sticking or catching. The monthly item is a syringe leak test. The spirometer itself gets the calibration verification at the interval the manufacturer specifies, plus routine maintenance at the manufacturer's intervals.

Gloves belong on the daily list too: a testing session is hands-on. Nitrile gloves — 3.5 mil, 1,000 per case and a fresh paper strip on the bench between workers are the two consumables that disappear fastest in a busy surveillance day.

What belongs in the calibration log?

The 2019 statement lists the minimum quality assurance requirement plainly: a log of calibration results, and documentation of repairs or alterations that return the equipment to acceptable operation. A clinic with only the first half cannot show a serviced device was fit for use.

Roll of smooth white examination table paper

Record field What it establishes Where it comes from
Device identifier and serial number Which spirometer produced the traces Asset register
Date and time of the check That the check preceded the session Daily work sheet
3-L syringe serial and last verification date That the reference volume itself is sound Syringe certificate
Volume read for each stroke The raw measurement, not a tick in a box Calibration log
Pass or fail against the stated tolerance The decision rule applied that day Clinic quality manual
Corrective action and repair note That the device was returned to service properly Service record

Who owns the spirometry record in a Canadian occupational health programme?

The employer's occupational health programme owns the surveillance record, and the clinic that performs the test holds the health file that supports it. Retention periods come from the provincial occupational health regime and from the record-keeping rules of the professional college that governs the tester. No federal licensing rule sets a calibration interval or a log format: that obligation sits with the surveillance programme.

Which supplies does a session consume?

A single-use patient interface per worker, gloves and a clean paper cover, part of the clinic consumables order. A peak flow meter — lung function monitor for asthma and COPD is a different device with a different record trail, useful for home monitoring but not a substitute for a diagnostic spirometer with a calibration log.

Ordering for a clinic, lab or care home? Wholesale and multi-site ordering covers case pricing and account setup, and the B2B wholesale collection lists the lines stocked for institutional buyers. Reselling? become a distributor.

References

  1. Standardization of Spirometry 2019 Update, American Thoracic Society and European Respiratory Society (Graham et al., Am J Respir Crit Care Med 2019;200:e70-e88) (checked 8 November 2026)

Printable companion: the free log and checklist library includes a calibration register laid out for device ID, syringe serial and pass or fail, ready to print for the testing room.

Building a cost per worker tested? The clinic supply and cost planner converts workers tested per month into gloves, paper and interface counts.

Related Reading

Frequently Asked Questions

How often does a spirometer need a calibration check?

Volume calibration is verified with a 3-L syringe at the interval the manufacturer specifies, and the syringe itself gets a daily check for a displaced piston stop and smooth operation, plus a monthly leak test.

What tolerance counts as a pass?

The 2019 ATS/ERS statement sets the maximum permissible error at ±2.5% when the device is tested with a 3-L syringe against the ISO 26782 profiles, which is tighter than the 3.5% figure still printed on many log sheets.

Does a federal rule set the calibration interval?

No. The record obligation comes from the occupational health surveillance programme and the clinic's own quality manual, not from the device licensing system.

Do workers need a new mouthpiece or filter each time?

Yes, each worker gets their own single-use patient interface, and the record should show which lot was used when a session is reviewed.

Last updated: November 2026. CliniEco Medical is a licensed medical device establishment (MDEL #35334).

Already working with clinics? Become a regional representative.