Flame Emission Photometers in Canada vs the US: Which Class Applies?

Pair of blue nitrile examination gloves laid out flat for a clinic tray

Quick facts

  • A flame emission photometer for clinical use measures electrolytes such as sodium and potassium in body fluids by reading the light emitted when a sample is introduced into a flame.
  • In the United States it is filed under 21 CFR 862.2540, Flame emission photometer for clinical use, at Class I, product code JJO.
  • In Canada it is an in vitro diagnostic device, so the IVDD rules in Part 2 of Schedule 1 of the Medical Devices Regulations apply rather than the Part 1 rules.
  • Under Part 2, the default for an IVDD that is not otherwise caught is Class I under Rule 8, but a device used for diagnosis or patient management is Class II under Rule 4 unless a listed exception applies.
  • A near-patient version - one intended for use outside a laboratory - is Class III under Rule 6, which is the largest single difference in this article.
  • Entries, rule text and product codes below were checked against the current eCFR text, the Regulations and the openFDA classification database on 2026-10-11.

A flame emission photometer reads sodium, potassium and lithium by the colour a sample burns. In the United States it has a named Class I entry, and the instrument has been classified that way for decades. In Canada the same instrument is an in vitro diagnostic device, and where it is placed depends on how it is used: a laboratory instrument, a diagnostic device, or a near-patient device placed at the bedside. This article sets out the three placements, the standards behind the instrument, and the sentence in the instructions that decides which one applies.

A photometer bench is wiped and swabbed between runs, and the cotton swabs, individually wrapped 200 pack are stocked for it.

What is a flame emission photometer for clinical use?

The photometer atomises a small sample in a flame and measures the light that the excited atoms emit. Each element emits at its own wavelength, so the instrument can separate sodium from potassium from lithium in the same run. The output is a concentration a clinician reads against a reference interval.

The instrument is a measuring device for body fluids. It is not a reagent and not a test kit; the calibration and the control materials do the chemistry, and the photometer supplies the measurement. That split matters in Canada, because the classification rule that applies depends on the intended use of the whole system and not only on the instrument.

Is a flame emission photometer a Class I device in the United States?

Yes. 21 CFR 862.2540 names a Flame emission photometer for clinical use and classifies it at Class I (general controls). The openFDA device classification API lists the product code as JJO. The entry exempts the device from premarket notification, so the instrument reaches the US market under registration and listing rather than a per-device review.

The US entry does not distinguish between a photometer on a laboratory bench and a photometer beside a patient. It names one device and reads one class from the name, and a US buyer therefore finds a single answer for the whole family.

How does Canada classify a flame emission photometer?

Canada starts from the definition. An in vitro diagnostic device is a medical device intended to be used in vitro for the examination of specimens taken from the body, so a photometer that measures electrolytes in body fluids is classified in Part 2 of Schedule 1. The placement inside Part 2 then depends on how it is used.

Rule 8 provides the floor: where rules 1 to 7 do not apply, all other IVDDs are Class I. Rule 4 lifts a device that is intended to be used in diagnosis or patient management to Class II, unless one of its listed categories applies. And Rule 6 states that a near patient IVDD is classified as Class III. The Regulations define a near patient IVDD as one intended for use outside a laboratory, for testing at home or at the point of care, such as a pharmacy, a health care professional's office or the bedside.

Item Canada United States
Named entry None; classified under Part 2 of Schedule 1 21 CFR 862.2540, Flame emission photometer
Product code Not applicable JJO
Bench instrument, general use Class I (Part 2, Rule 8) Class I (general controls)
Used in diagnosis or patient management Class II (Part 2, Rule 4) Class I (entry unchanged)
Near-patient version, outside a laboratory Class III (Part 2, Rule 6) Class I (entry unchanged)
Route to market Device licence where above Class I Registration and listing

Where is a near-patient photometer used, and why does it matter?

A near-patient device is one placed outside the laboratory - a clinic room, a pharmacy counter or a bedside. The Regulations name those settings explicitly, so the test is where the device is intended to be used, not where a particular unit happens to sit.

This is the single largest difference in this article. The same measuring principle that is Class I on a laboratory bench is Class III when the manufacturer intends it for use at the point of care, because a reading taken away from a laboratory carries a different set of risks around operator training, quality control and turnaround. A buyer who is planning a point-of-care electrolyte service should expect the Canadian paperwork to be heavier than the US entry suggests.

Which photometer types sit in the same class?

The class follows the setting and the claim, not the optical design. A single-channel photometer, a multi-channel instrument and a photometer built into a larger analyser all measure the same way; what separates them in Canada is whether the manufacturer represents them for laboratory use or for use outside it.

Instrument type Typical setting Class, Canada Class, US
Single-channel bench photometer Hospital laboratory I (Part 2, Rule 8) I (862.2540)
Multi-channel bench photometer Hospital laboratory I (Part 2, Rule 8) I (862.2540)
Photometer for a named diagnostic use Laboratory, reported to a clinician II (Part 2, Rule 4) I (862.2540)
Photometer intended for a clinic room Point of care III (Part 2, Rule 6) I (862.2540)
Photometer used only for teaching Not for patient testing Out of scope Out of scope

The detail worth carrying into a purchase order is the intended setting. A laboratory that buys a bench instrument is buying a Class I device in Canada; a clinic that buys the same principle for a treatment room is buying a Class III device. Writing the setting into the specification keeps the two buys in the right lane.

Which standards apply to a clinical photometer?

The class says what the device is; the standards say how it must behave. The quality system behind the instrument follows ISO 13485:2016, and the risk file follows ISO 14971:2019. A laboratory that operates it works under a management system of its own, which in Canadian laboratories is often aligned with ISO 15189 as the reference for quality and competence in medical laboratories.

For the bench, the practical material is the methods and quality guidance. The Clinical and Laboratory Standards Institute publishes the method and quality documents clinical laboratories work to, and Public Health Ontario publishes the laboratory services material that Ontario laboratories use. A point-of-care service adds operator training and quality control to the same list.

How should a laboratory choose and record a photometer?

Choose by setting first. A laboratory bench instrument is bought for throughput and repeatability; a point-of-care instrument is bought for portability, for a small operator interface and for a control routine a clinician can run between patients. The two are different devices on paper, and the Canadian class follows the setting.

Record by run. The consumables that travel with a bench - specimen containers for sample handling, cotton swabs for bench work, nitrile examination gloves for every operator and a pre-perforated exam table roll where a sample is taken - belong on the same restock list, and the run log is kept with the instrument. Multi-site groups order at case level through the wholesale and multi-site ordering page. Reselling? become a distributor.

Pair of blue nitrile examination gloves laid out flat for a clinic tray Examination table with a fresh roll of paper dispensed across the upholstery in a clinic room

Sources

  1. openFDA device classification API
  2. Medical Devices Regulations, SOR/98-282, full text and Schedule 1
  3. US FDA, medical device classification database
  4. Electronic Code of Federal Regulations, title 21
  5. ISO 13485:2016, medical devices quality management
  6. ISO 14971:2019, risk management of medical devices
  7. Health Canada, medical devices
  8. Standards Council of Canada
  9. CSA Group
  10. World Health Organization
  11. CCOHS, OSH answers
  12. Clinical and Laboratory Standards Institute
  13. Public Health Ontario, laboratory services
  14. ISO 15189:2022, medical laboratories, requirements for quality and competence
  15. World Health Organization, laboratory biosafety guidance
  16. National Center for Biotechnology Information, bookshelf
  17. 21 CFR 862.2540, Flame emission photometer for clinical use
  18. openFDA device classification API
  19. Public Health Ontario, laboratory services

An electrolyte result is only as good as the control that ran beside it. The printable bench control sheet at the compliance log centre has a column for the control lot and the acceptance window next to every patient run, and it prints from the browser without an account and no sign-up.

For a point-of-care service, the log generator on the same page builds a sheet per testing site, so a clinic room and a pharmacy counter each keep their own record instead of sharing one form.

Have a question about your own facility? Send it in and you will get a written answer specific to your equipment and province, with the regulation or standard it is based on cited. Ask a compliance specialist about the device you are buying.

Related reading

CliniEco Medical supplies eye care, laboratory and dental consumables of the kind described in this article. MDEL #35334. This article is written for optometry, laboratory and dental procurement professionals and is not legal advice; the class of a device and the records kept by a practice belong to the manufacturer and to the requirements that apply to it.

Frequently Asked Questions

Is a flame emission photometer a Class I device?

It is Class I in the United States under 21 CFR 862.2540. In Canada the instrument on a laboratory bench is Class I under Rule 8 of Part 2 of Schedule 1, because it is an in vitro diagnostic device that the earlier rules do not catch.

When is a photometer Class II in Canada?

Rule 4 of Part 2 classifies an IVDD intended to be used in diagnosis or patient management as Class II, unless one of its listed categories applies. A photometer represented for a diagnostic use is therefore Class II rather than Class I.

What is a near patient IVDD?

The Medical Devices Regulations define a near patient IVDD as an in vitro diagnostic device intended for use outside a laboratory, for testing at home or at the point of care, such as a pharmacy, a health care professional's office or the bedside. Rule 6 classifies a near patient IVDD as Class III.

Does the US class change for a point-of-care photometer?

No. The United States classifies the instrument on its own entry at 862.2540, and the entry does not distinguish a laboratory bench from a point-of-care setting. The Canadian class does change, because Rule 6 acts on the intended setting.

What is the US product code for a flame emission photometer?

The openFDA classification database lists the flame emission photometer for clinical use under product code JJO, within regulation number 862.2540 at Class I.

Does a Class I photometer need a device licence in Canada?

No. A Class I device does not get a device licence of its own; the manufacturer holds an establishment licence and keeps the records the Regulations require. A Class II or Class III device needs a device licence under section 32.

How should a bench photometer be recorded?

With a run log that carries the control lot and its acceptance window beside the patient results, kept with the instrument. The compliance log centre provides a printable bench control sheet and a generator that builds a sheet per testing site.

Already working with clinics? Become a regional representative.