Dental X-Ray Sensor Covers in Canada vs the US: Which Class Applies?

Sterile oral swabsticks laid out for a dental procedure

Quick facts

  • A digital intraoral sensor is filed in the United States as an intraoral X-ray unit at 21 CFR 872.1810, a Class II device, and the disposable cover placed over it is handled as an accessory to that device.
  • In Canada the sensor is a device in its own right, and a cover that does not touch the patient's mucosa and is not wired to a device is a non-invasive device classified as Class I under Rule 7(1) of the Medical Devices Regulations.
  • The disposable cover is a cross-infection control, not a sterility claim: the sensor and its cable touch the patient's hand, the bite block and the operatory surfaces, and the cover is changed between patients.
  • The cover must not interfere with the image — a wrinkled or opaque sleeve over the active face is a retake, and a retake is a dose the patient did not need.
  • The entries and rule text below were checked against the current eCFR text and the Regulations on 2026-10-07.

A dental X-ray sensor cover is the thin disposable sleeve slipped over a digital intraoral sensor and its cable so the sensor does not have to be disinfected between patients. In the United States the sensor is a Class II device and the cover is an accessory; in Canada the cover is a non-invasive device filed by rule. This article compares the two rulebooks, sets out what the cover must do to the image, and explains why the cover and the bite block are two separate parts of the same exposure.

What is a dental X-ray sensor cover?

It is a sleeve or a flat pouch, made from a thin plastic that is transparent to X-rays, that is fitted over the sensor and along part of the cable. It is used once and discarded. Some holders combine the cover with a bite block, so the patient bites on a disposable tab while the sensor is held behind the tooth.

The cover is not sterile and does not need to be, because it does not enter a wound and does not contact mucous membrane in a way that a bite block does not already. Its purpose is to keep the sensor, which cannot be autoclaved, from carrying a patient's flora to the next patient.

Why is the sensor a device and the cover an accessory?

A device is defined by the function it performs. The sensor converts X-rays into an image that is used to make a diagnosis, so it is a diagnostic device and carries the class the named entry gives it. The cover performs no measuring function; it protects the device. In the United States an accessory is filed with the device it supports, so the cover sits with the sensor rather than on its own entry.

For a practice, the practical reading is that the class belongs to the sensor and the cover follows it. A cover sold as a plain piece of plastic is a general supply; the same cover sold to maintain the infection-control status of a clinical sensor is described as doing something for patient safety, and where that is a device claim the product is a non-invasive device in Canada.

How do Canada and the United States treat a sensor and its cover?

The two countries reach different classes for the sensor and the same rule for the cover.

Item Canada United States
Sensor entry Non-invasive device; the digital sensor is licensed as a device 21 CFR 872.1810, Class II
Sensor product code Not applicable EAP
Disposable cover Class I non-invasive device where a device claim is made Accessory to the sensor under general controls
Film holder Class I non-invasive device where a device claim is made 21 CFR 872.1905, Class I
Beam aligner Class I non-invasive device 21 CFR 872.1820, Class I
Route to market Class II needs a licence under section 32; Class I does not Class II needs a 510(k); Class I is generally exempt

In Canada a cover that does not enter the body and is not connected to an active device is a non-invasive device where a device function is claimed, and under Rule 7(1) of the Medical Devices Regulations "all other non-invasive devices are classified as Class I." The sensor itself is a device whose class follows its intended use and its licence.

In the United States the sensor is filed under 21 CFR 872.1810, which covers an intraoral X-ray unit at Class II under product code EAP, and the openFDA device classification API lists the entry. The cover is an accessory to that device; the film holder and beam aligner have their own Class I entries at 21 CFR 872.1905 and 21 CFR 872.1820.

What must a cover do to the image?

The class table says what the parts are; the imaging requirement says how the cover must behave. Quality management for the device is ISO 13485:2016, and risk management is addressed by ISO 14971:2019.

Property What it fixes Why it matters at the chair
Radio-transparency The sleeve's effect on the beam An opaque cover absorbs the signal and darkens the image
Flatness Freedom from wrinkles over the active face A wrinkle casts a line that looks like a fracture
Fit The size that covers the sensor and cable A loose cover slips into the beam or leaves the cable bare
Seal The join that keeps fluid out A leaking cover puts fluid on a sensor that cannot be autoclaved
Disposal One use only A re-used cover defeats the control it exists to give
Handling Gloves on removal The cover is contaminated when it comes off

The practical consequence is that two covers of the same size can give different images if one lies flat over the active face and the other wrinkles under the beam. A practice that rejects a cover at the first wrinkle is protecting the patient from a retake rather than only the sensor from fluid.

Foam-tipped oral swabsticks laid out for a dental procedure

What does a dental radiography tray restock alongside its covers?

The cover is one item on a tray that is restocked as a set. The disposable dental bibs cover the patient during the exposure, and the sterile cotton rolls handle moisture control where the sensor has to sit against a dry tooth. The medical gauze sponges handle the wipe-down where a surface is bare, and the saliva ejector tips carry the suction line that is itself covered at the handpiece. Clinics that monitor their own steriliser pair the sterilization monitoring collection with the 24-hour biological indicator 25-pack. Multi-site groups ordering at case level use the wholesale ordering page, and the B2B wholesale collection lists the lines held for institutional buyers. Reselling? become a distributor.

Sterile medical gauze sponges in a dental operatory

How is a sensor cover used in practice?

The sensor is placed in a holder, the cover is slipped over the sensor and down the cable, and the assembly is positioned with the bite block. The exposure is made, the assembly is removed, and the cover is taken off with gloves on and discarded. The sensor is checked for any fluid that reached it, and a fresh cover is fitted before the next exposure. A cover is never re-used, even if the exposure had to be repeated.

A practice that records the exposure and the cover change together can show that a retake was a positioning decision and not a cover that spoiled the image. The record also answers the question an infection-control review will ask: was the sensor itself ever uncovered against a patient.

Sources

  1. 21 CFR 872.1810, Intraoral source x-ray system
  2. 21 CFR 872.1905, Film holder (dental x-ray)
  3. 21 CFR 872.1820, Dental x-ray exposure alignment device
  4. openFDA device classification API
  5. Medical Devices Regulations, SOR/98-282, full text and Schedule 1
  6. Health Canada, medical devices
  7. CDC, Guidelines for Infection Control in Dental Health-Care Settings, MMWR 2003
  8. Royal College of Dental Surgeons of Ontario
  9. Canadian Dental Association
  10. ISO 13485:2016, medical devices quality management
  11. ISO 14971:2019, risk management of medical devices
  12. ISO 11143:2008, dentistry, amalgam separators
  13. CSA Group
  14. Standards Council of Canada
  15. Public Health Ontario, infection prevention and control
  16. US FDA, medical devices
  17. CCOHS, OSH answers
  18. World Health Organization, infection prevention and control

Where a cover change is recorded

An exposure record that does not note the cover cannot answer an infection-control review. The printable imaging equipment log is a blank sheet with columns for the patient, the sensor, the holder, the cover change, the exposure and the operator, so the two controls — image quality and cross-infection — are visible on one line. The imaging log generator on the same page sizes the form to the number of radiographic units a practice runs. No account and no sign-up are needed to open either one.

Every unit and every sensor differs. Ask a compliance specialist and you will get a written answer specific to your equipment and province, with the regulation or standard it is based on cited.

Related reading

CliniEco Medical supplies eye care, laboratory and dental consumables of the kind described in this article. MDEL #35334. This article is written for optometry, laboratory and procurement professionals and is not legal advice; the class of a device and the records kept by a clinic belong to the manufacturer and to the requirements that apply to it.

Frequently Asked Questions

Is a dental X-ray sensor cover a regulated device?

The sensor is: the United States files a digital intraoral sensor as an intraoral X-ray unit at 21 CFR 872.1810, a Class II device, and the cover is an accessory to it. In Canada the cover is a Class I non-invasive device where a device claim is made under Rule 7(1) of the Medical Devices Regulations.

Does a sensor cover have to be sterile?

No. The cover does not enter a wound and does not contact mucous membrane beyond where the bite block already sits, so it is not presented as sterile. It is handled as contaminated on removal, which is why gloves and hand hygiene apply.

Why does a wrinkled cover matter?

Because the wrinkle sits in the X-ray beam and can cast a line that reads as a fracture or a gap on the image. A practice that rejects a wrinkled cover avoids a retake and the extra dose a retake carries.

Can the sensor be disinfected instead of covered?

A digital sensor cannot be autoclaved, and its housing is not made for repeated immersion. The cover is the practical way to keep the sensor from carrying flora between patients while it is protected from fluid.

How often should a sensor cover be changed?

Between every patient, and after any exposure where the cover was torn or fluid reached the sensor. A cover is never re-used, because a re-used cover defeats the control it exists to give.

Which entry covers a dental X-ray film holder in the United States?

21 CFR 872.1905 covers a dental X-ray film holder at Class I, and the beam alignment device has its own Class I entry at 21 CFR 872.1820. The openFDA classification database lists both entries.

Does the cover change the class of the sensor?

No. The sensor keeps its own class and the cover follows it as an accessory. In Canada the cover is classified on its own intended use, which is a non-invasive device under Rule 7(1) where a clinical function is claimed.

Where can a practice keep its imaging records?

The printable imaging equipment log at the compliance log centre has columns for patient, sensor, holder, cover change, exposure and operator, and the log generator on the same page sizes the sheet to the number of radiographic units a practice runs.

Already working with clinics? Become a regional representative.