What Auditors Check About CPAP Accessories Pack in Canada Clinics

A CPAP accessories pack laid out on a white background: a full-face interface with headgear, a coiled corrugated hose and two individually wrapped filters

Quick facts

  • A CPAP machine is a Class II device in Canada, so the manufacturer needs a medical device licence before the device can be sold or even advertised for sale.
  • The mask, hose and filters usually carry no licence number of their own — if they are components of a licensed system and made by that system's manufacturer, section 28 of the Medical Devices Regulations deems them licensed.
  • The seller needs an establishment licence; a clinic buying for its own patients does not, because section 44(2) excludes health care facilities.
  • The label is a checked item, not a formality: name of the device, manufacturer, identifier, package contents, and the word "Sterile" where it applies.
  • In the United States the same circuit is cleared under 21 CFR 868.5905, where a reprocessed ventilator mask is a Class II device whose 510(k) must include reprocessing validation.
  • The record an auditor wants is the one that ties a serial number to a patient and a date — not the invoice.

A CPAP accessories pack is one of the few products in a clinic where the paperwork is more complicated than the device. The mask is patient-specific, the hose is not, the filters are consumable, and the whole set is sold under a licence held by a company the clinic never deals with. That structure is why audits in this category go after three things in order: what the pack legally is, who was allowed to sell it, and whether the clinic can show which patient received which serial number on which date. This page walks that sequence, compares it with the American route, and sets out the records that make the answers available on the day they are asked for. The pack used as the example is the CPAP accessories pack with mask, tubing and filter kit.

What does an auditor ask first about a CPAP circuit?

Three questions, and the first one is not about the product.

Who is this mask for? A CPAP interface is fitted to a face. It is not a stock item that can be handed to whichever patient is next, and an auditor who finds one mask serving multiple patients has found a reprocessing failure regardless of what the cleaning log says.

What was it fitted against? The mask size and type follow the patient's therapy pressure and face geometry, and the clinic's record should show that the choice was made by someone qualified to make it, on a date, with the device serial number recorded.

What happened at the last replacement? The interval that matters is the one in the manufacturer's instructions for use or in the payer's policy, whichever applies to that patient, and the record should show the date the previous item was issued.

None of those three questions is answered by a purchase invoice. That is the gap most clinics discover during the audit rather than before it.

Is the pack licensed in Canada, or does it ride on the machine's licence?

Both, depending on how the pack is put together, and the distinction is written into the regulations.

A CPAP machine is an active therapeutic device that maintains positive airway pressure, which places it in Class II under Schedule 1 of the Medical Devices Regulations. Class II means the manufacturer must hold a medical device licence, and section 26 makes it unlawful to import or sell the device without one. Section 27 extends the same condition to advertising the device for sale.

The accessories are covered by a different provision. Section 28 states that if a system is licensed, all of its components or parts that are manufactured by the manufacturer of the system are deemed — for the purposes of importation, sale or advertisement — to have been licensed. A mask, a hose and a filter made by the same company that holds the machine licence therefore travel on that licence.

What is being sold Regulatory status in Canada What the clinic should hold
CPAP machine Class II; manufacturer holds a device licence Licence number, and the device record per serial number
Mask, hose and filters from the machine's manufacturer Deemed licensed as components of a licensed system (section 28) The pack label showing the manufacturer, plus the IFU
The same accessories from a third-party manufacturer Their own status, which depends on how they are represented A licence number or a written classification position from the supplier
A pack assembled by a distributor from mixed sources Each component keeps its own status A bill of materials with the source and status of each item

The last two rows are where a clinic's file usually goes thin. A distributor-assembled kit that mixes a licensed mask with an unlicensed third-party hose is not a licensed kit; it is a licensed component plus an unlicensed one, and the clinic that cannot produce the bill of materials cannot answer the question.

What must the label show?

Section 21 of the regulations sets the minimum content for a device label, and the list is short enough to check at receipt.

  • The name of the device.
  • The name and address of the manufacturer.
  • The device identifier, including the identifier of any device that is part of a system, kit or group.
  • An indication of what the package contains, where the contents are not obvious — expressed as size, weight, length, volume or number of units.
  • The word "Sterile", where the manufacturer intends the device to be sold sterile.
  • The expiry date, where one exists, set by the component with the shortest projected life.

For a pack the fourth item does the most work. A box that says "CPAP accessories pack" and nothing else does not tell a receiver whether it contains one mask or two, a six-foot hose or a heated one, two filters or ten. The label is also the only place the clinic can confirm the manufacturer's identity when the pack arrives under a distributor's name.

Who needs an establishment licence?

The seller, not the buyer — and the wording is specific enough that there is no room for a middle position. Section 44(1) prohibits importing or selling a medical device without an establishment licence. Section 44(2) then lists the parties to whom that prohibition does not apply, and a health care facility is one of them when it imports or sells for its own use.

That produces three practical consequences:

  • A clinic can receive a CPAP pack from a licensed importer without holding an establishment licence of its own.
  • The clinic should still be able to name the importer's establishment licence, because that is the party the licence obligation actually sits with.
  • A clinic that starts supplying another site — a satellite office under a different corporation, a long-term care home, a patient's family — has left the "own use" exclusion and needs a regulatory opinion before the first shipment.

How does the Canadian route compare with the FDA's?

The two systems regulate the same circuit through different instruments. Canada licenses the manufacturer and then deems the components licensed; the United States clears the system through a premarket notification and describes the accessories inside that clearance.

Item Canada United States
Instrument Medical device licence for the manufacturer, under the Medical Devices Regulations 510(k) premarket notification, under 21 CFR 868.5905
Class of the machine Class II Class II
Class of a mask Deemed licensed as a component of the system Depends on the classification: an oxygen mask is Class I and exempt, while a reprocessed ventilator mask is Class II with a 510(k)
Filters and tubing Deemed licensed if part of the licensed system Cleared as accessories of the system
Advertising A licensed device may be advertised for sale only if the manufacturer holds the licence (section 27) Promotion is policed under the FD&C Act and the labelling rules
Who the clinic deals with The importer or distributor, whose establishment licence is the checkable document A supplier enrolled with the payer, whose 510(k) number is the checkable document
Visible evidence of compliance Licence number in the active licence listing 510(k) number in the premarket notification database

The Class I oxygen mask row is the one that confuses buyers. A mask is not automatically a Class II device in the United States: the classification follows the intended use, and a mask intended to deliver oxygen sits in 21 CFR 868.5580 as Class I and is exempt from 510(k). A reader who assumes every mask carries the same status will misread both markets.

What changes if a mask is reprocessed?

The American classification answers this directly, and it is worth knowing even in Canada, because reprocessed interfaces are sold across the border.

Under 21 CFR 868.5905, the product code for a reprocessed non-continuous ventilator mask is Class II, and the FDA's own classification record states that reprocessing validation data must be included in the 510(k) submission. In other words, the act of reprocessing changes the regulatory object: a mask that is cleaned and returned to service is not the same article, for regulatory purposes, as a mask that is discarded after one patient.

A Canadian clinic's practical rule follows from the same logic even though the instrument differs. A CPAP mask is fitted to a patient and stays with that patient; it is not reprocessed between patients, and a clinic that tries to run one through a cleaning cycle to reuse it on someone else has taken on a validation obligation it cannot discharge with a wipe. The safe position is the one written on most instructions for use: single patient use.

What records prove a pack was issued correctly?

Record What it must show Which question it answers
Patient assignment Patient identifier, mask type and size, date fitted, fitter Who is this mask for
Device traceability Serial or lot number of the machine and of the interface Which device was involved if a recall is issued
Issue and replacement log Date of each mask, hose and filter issue, and the interval applied What happened at the last replacement
Instruction record That the patient was taught the cleaning routine, and when Whether the clinic discharged its training duty
Complaint and incident file Any report of skin breakdown, seal failure or device fault, with the date reported Whether a signal was acted on
Supplier file Establishment licence number for the importer, and the licence or 510(k) reference for the device Who was allowed to sell it

The second row is the one that pays for itself. A recall letter names a lot number; a clinic that recorded lot numbers can answer in an hour, and a clinic that recorded only product names has to contact every patient on the list.

How should cleaning and replacement be evidenced?

The cleaning routine is a teaching item and a record item at the same time. The mask and hose are washed weekly in warm water with mild soap and air dried away from direct sunlight, per the manufacturer's instructions; the water chamber is emptied daily and refilled with distilled water where a humidifier is in use; the disposable filter is replaced, never washed.

For the clinic the evidence is not a cleaning log of its own sessions — the patient does the cleaning — it is the instruction record plus a replacement log that shows the clinic acted when a patient reported a failing seal. That combination answers the two questions an auditor actually has: was the patient taught, and did the clinic respond when the teaching did not hold.

Where the clinic does handle the device — a sleep laboratory that runs titration studies, for instance — the equipment becomes clinic equipment and the provincial reprocessing guidance applies in the ordinary way. An interface that touches mucous membranes is not a non-critical item, and a shared device in a laboratory setting needs a defined reprocessing procedure rather than a wipe between patients.

A CPAP accessories pack laid out on a white background: a full-face interface with headgear, a coiled corrugated hose and two individually wrapped filters An adjustable care bed with white sheets and a blue-bordered underpad in a treatment room, the setting in which an interface is fitted and its serial number recorded

What happens when a supplier issues a recall?

A recall is the moment the traceability record is tested, and the sequence is short.

Identify. Match the recalled lot or serial numbers against the issue log. This is why the lot number goes on the record at issue, not at the end of the month.

Contain. Stop issuing the affected stock, and separate it physically rather than by a note on the shelf.

Notify. Contact the patients who received an affected unit, and record the contact attempt and the outcome. A patient who cannot be reached is a documented fact, not a gap.

Report. Where the event meets the reporting threshold, the report goes to the supplier and onward to Health Canada; the clinic's own file should show that the supplier was notified and when.

A clinic that has the first step can do the other three; one that does not cannot do any of them.

CliniEco Medical supplies respiratory consumables in Canada under MDEL #35334. This page describes regulatory expectations and clinic practice; it is not a substitute for the manufacturer's instructions for use, and the licence status of a specific device should be verified in Health Canada's active licence listing.

Sources

  1. Medical Devices Regulations, SOR/98-282 — consolidated text (s.21, s.26, s.27, s.28, s.44)
  2. Medical Devices Regulations, Schedule 1 — classification rules
  3. Food and Drugs Act, R.S.C. 1985, c. F-27
  4. Health Canada — Medical devices
  5. Health Canada — Medical Devices Active Licence Listing (MDALL)
  6. 21 CFR 868.5905 — Ventilator, non-continuous (respirator)
  7. 21 CFR 868.5580 — Oxygen mask
  8. openFDA — Device classification API (product codes BZD, NMC, BYG)
  9. FDA — Medical device classification database
  10. FDA — 510(k) premarket notification database
  11. CMS — Medicare coverage database, positive airway pressure devices (LCD L33718)
  12. Highmark — Attachment E-34, PAP accessory frequency table by HCPCS code
  13. ISO 17510-2:2007 — Sleep apnoea breathing therapy, masks and application accessories
  14. ISO 18562-1:2024 — Biocompatibility evaluation of breathing gas pathways
  15. Public Health Ontario — Infection prevention and control
  16. Peel Public Health — Reprocessing in community health care settings (Spaulding table)
  17. IPAC Canada — Practice recommendations for non-critical multi-use equipment
  18. CSA Group — CSA Z314:23, Reprocessing of medical devices in health care settings
  19. ISO 14971:2019 — Application of risk management to medical devices

The traceability sheet this page describes — patient, serial, lot, issue date, replacement date — is a one-page record, and the printable version sits in the free compliance log pack alongside the daily sheets; when a recall letter arrives and the clinic needs a dated page for the month in a hurry, the sterilization log generator on the same page prints one immediately.

If the licence status of a third-party accessory is unclear, or a mixed-source pack has no bill of materials, that question is worth resolving before the equipment is issued rather than after: raise it with the sterilization compliance consultation desk. Multi-site clinics that dispense to several locations can arrange the supply on the wholesale enquiry page. Reselling? become a distributor.

Related reading

Frequently Asked Questions

Does a CPAP accessories pack need its own medical device licence in Canada?

Usually not. Section 28 of the Medical Devices Regulations deems components of a licensed system to be licensed when they are manufactured by that system's manufacturer. A third-party accessory that is not part of any licensed system does not inherit that status, so the supplier should be able to state which case applies.

Can a clinic import a CPAP pack directly from the United States?

A health care facility importing for its own use falls outside the establishment licence requirement in section 44(2), but the device still has to be licensed for sale in Canada. Importing a device that has only an FDA clearance, and no Canadian licence, is not made lawful by the facility exemption.

Is an FDA 510(k) number enough evidence for a Canadian audit?

No. A 510(k) number shows that the FDA reviewed an intended use for the American market; it is not a Canadian licence. The check a Canadian auditor can repeat is the device's entry in Health Canada's active licence listing.

Do masks, hoses and filters need lot numbers in the clinic record?

They need enough traceability to respond to a recall. Recording the lot at issue is the difference between answering a recall letter in an hour and telephoning every patient on the list. The machine serial number should be recorded for the same reason.

Can one mask be used for more than one patient if it is disinfected?

No. A CPAP interface is fitted to a face and is supplied for single patient use; reprocessing it for another patient is a validation exercise, not a cleaning task, and the FDA treats a reprocessed ventilator mask as a Class II device requiring reprocessing validation in its 510(k).

What has to be on the pack label?

The device name, the manufacturer's name and address, the device identifier, an indication of what the package contains, the word "Sterile" where the device is sold sterile, and an expiry date where one exists. For a kit, the contents statement is the field that matters most at receipt.

Already working with clinics? Become a regional representative.