How Do You Dry Instruments Before Packaging?
Why a Dry Instrument Still Fails a Load
The instrument comes out of the ultrasonic bath, gets a rinse, gets shaken, and goes into a pouch. The cycle runs. The indicator changes colour. The pack is placed in the drawer, and three weeks later a hinge is stiff and there is a brown line inside the box lock.
Nothing in that sequence looks wrong on a log sheet, which is the problem. Drying is the step that has no visible output when it is done correctly and no error message when it is skipped. It is also the step that decides whether the sterilizer's validated conditions were actually reached on the surfaces that matter.
This guide covers where water hides on a cleaned instrument, what the washer-disinfector does and does not dry, when compressed air is acceptable, and how to write a drying and inspection step that someone else can follow and sign.
What Counts as Dry?
Dry means no visible water and no residual film that will release vapour inside the pack. Three places fail that test most often:
- Hinges, ratchets and box locks, where water is held by capillary action and released slowly
- Lumens and cannulations, where air cannot circulate and the inside stays wet long after the outside looks dry
- Matte, sandblasted or anodised surfaces, where a thin film of water sits in the surface texture and reads as a slight sheen rather than a droplet
A visual check that only looks at the working end of an instrument will pass all three. That is why the check has to name the places rather than ask whether the instrument looks dry.
Where Does Water Hide on a Cleaned Instrument?
Four locations account for most of the failures seen in small clinics:
The hinge joint of a scissors, haemostat or forceps holds water in the gap between the two halves. Opening and closing the joint once after rinsing releases some of it, and leaving it closed traps the rest.

The box lock and the ratchet of a hinged instrument hold water in a machined recess that a towel cannot reach.
A lumen holds water along its whole length, and the last few centimetres are the ones that never dry by gravity.
The screw threads and the mating faces of an instrument that comes apart hold water in the interface, which is why manufacturer instructions often require dismantling before cleaning and drying.
A set that is dried correctly then goes into a pouch or a length of 76 mm sterilization roll, and the packaging stage is where drying gets tested: a paper-film pouch will show a wet pack, while a length cut from a roll will show it at the fold.
What Does the Washer-Disinfector Drying Stage Do?
A washer-disinfector is specified and tested as a process under ISO 15883-1, with the instrument-specific requirements for thermal disinfection in ISO 15883-2. Drying is part of that process: the load leaves the chamber hot, and the residual heat drives off water from surfaces the air can reach.
What the chamber cannot do is reach into a closed box lock or down a long narrow lumen with the same effectiveness. The drying stage reduces the water load; it does not remove the need for the manual check. A clinic that treats "it came out of the machine" as proof of dryness has replaced a check with an assumption.
How Do You Dry Instruments by Hand?
Four methods, in order of how often they are appropriate:
| Method | Where it works | Where it fails |
|---|---|---|
| :-- | :-- | :-- |
| Rack air-dry in a ventilated reprocessing area | Flat instruments, trays, items with no lumen | Hinges left closed, deep lumens, humid rooms |
| Lint-free absorbent towel, dabbing not wiping | Exterior surfaces of solid instruments | Any lumen, any matte finish, any hinge interior |
| Medical-grade compressed air with a point-of-use filter | Lumens, screw threads, blind holes | Oiled workshop air, dry bearings, seal faces |
| Drying cabinet with filtered warm air | Trays and sets held overnight | Throughput, if the clinic needs the set today |

The towel is the method most clinics use and the one that most often leaves fibre. A towel that sheds is a particulate source, and particulate inside a sterile barrier system is a defect that no indicator will show.
What About Lumens and Hinged Instruments?
Lumens get their own rule because gravity does not solve them. Position the lumen vertically, nozzle at the upper end, and pass air through in the direction the manufacturer specifies; then repeat from the other end. A lumen that is dry at one end and wet at the other is still wet.
Hinged instruments get a different rule: open the joint, dry it, then leave it open until the instrument is packaged. A closed hinge that goes into a pouch with water in it produces corrosion at the joint, and corrosion at a joint is the failure that shortens instrument life fastest.
Why Is Compressed Air a Specification, Not a Habit?
Because air is a fluid with a purity, and the compressor in a utility room was not installed for instrument drying. Under ISO 8573-1, compressed air is classified by particulate, water and oil content, and a workshop line sits in a class that carries oil aerosol.
Three controls make compressed air acceptable:
- A stated purity class in the SOP, not a general instruction to blow the instrument dry
- A point-of-use filter at the nozzle, changed on a schedule rather than when it looks dirty
- A nozzle that is not directed at bearings that will be lubricated afterwards, since air drives lubricant out of a bearing as effectively as it drives water out of a lumen
Where a clinic cannot state the class, the honest answer is that the air is unclassified and the towel-and-rack method is the compliant route.
How Do You Check Dryness Before Packaging?

Check, then record. The check takes about fifteen seconds per instrument and covers four points:
- Look into the hinge with the instrument open
- Look through the lumen against a light, both ends
- Run a gloved finger along the matte face and feel for a film
- Look at the screw threads and the mating faces
The record is a tick on the reprocessing sheet beside the step, initialled. A tick that nobody can be asked about later is worth little; a tick with a name and a time is the evidence that the step happened on that set.
| Check | What it catches | What it misses |
|---|---|---|
| :-- | :-- | :-- |
| Visual sweep of the exterior | Droplets, streaks | Water inside a closed hinge |
| Hinge opened and inspected | Joint water, corrosion start | Lumen interiors |
| Lumen viewed against light | Blocked or wet bore | Water held in a blind recess |
| Finger feel on matte surfaces | Surface film | Water under a box lock |
| Weight and rattle of a set | Bulk water in a tray | Anything inside a sealed instrument |
What Goes Wrong After Packaging?
Three failures trace back to moisture, and all three cost more than the drying step they replace.
A wet pack is visible moisture inside the pouch when it comes out of the cycle. It is a rejected load, a repeat cycle and a documented deviation. Corrosion at a hinge or a box lock is slower and more expensive: the instrument works, then sticks, then is removed from service. Stained instruments are the mildest outcome, and they are the one staff notice first, which is why appearance is a poor proxy for dryness.
Chemical indicators do not rescue any of this. An indicator confirms exposure to the process conditions at its location, and ISO 11140-1 defines what a chemical indicator has to do; it cannot confirm that the surface under a droplet reached the same temperature. Where a clinic relies on biological indicators for process verification, ISO 11138-1 governs those too, and neither indicator type compensates for a wet load.
How Do You Write Drying Into an SOP?
Five lines, and the SOP is usable:
- The method, named by instrument type, including which items go to the drying cabinet
- The check, with the four inspection points written out
- The record, on the reprocessing sheet, with initials and time
- The rejection rule, so a wet set is quarantined rather than repackaged
- The review point, where the manufacturer's processing information per ISO 17664-1 is checked against what the clinic actually does
That last line is the one that gets skipped and the one that matters most when a new instrument arrives. A clinic that buys a new hinged instrument with a lumen and follows the old SOP will dry it the old way, and the manufacturer's instructions are the document that says whether the old way works.
Clinics that order across several sites or buy for a group of rooms can route the specification through the wholesale account desk, which keeps the pouch format, the seal width and the indicator class on one account sheet. Reselling? become a distributor.
For the packaging half of the workflow, the sterilization pouch and roll range lists the formats and indicator classes on each product page. The pouches most clinics run are the Class 4 self-sealing dual-indicator pouches for small sets, the 76 mm by 50 m sterilization roll for longer instruments, and a constant-heat pouch sealer where the clinic heat-seals rather than self-seals.
References
- Medical Devices Regulations (SOR/98-282), section 1, interpretation (checked 13 November 2026)
- Medical Devices Regulations (SOR/98-282), section 21, label requirements (checked 13 November 2026)
- Medical Devices Regulations (SOR/98-282), section 52, distribution records (checked 13 November 2026)
- ISO 17665:2024, Sterilization of health care products, moist heat (checked 13 November 2026)
- ISO 17664-1:2021, Processing of health care products, information to be provided by the medical device manufacturer for the processing of medical devices (checked 13 November 2026)
- ISO 11607-1:2019, Packaging for terminally sterilized medical devices, requirements for materials, sterile barrier systems and packaging systems (checked 13 November 2026)
- ISO 11607-2:2019, Packaging for terminally sterilized medical devices, validation requirements for forming, sealing and assembly processes (checked 13 November 2026)
- ISO 15883-1:2006, Washer-disinfectors, general requirements, terms and definitions and tests (checked 13 November 2026)
- ISO 15883-2:2006, Washer-disinfectors, requirements and tests for washer-disinfectors employing thermal disinfection for surgical instruments (checked 13 November 2026)
- ISO 8573-1:2010, Compressed air, contaminants and purity classes (checked 13 November 2026)
- ISO 11140-1:2014, Sterilization of health care products, chemical indicators, general requirements (checked 13 November 2026)
- ISO 11138-1:2017, Sterilization of health care products, biological indicators for sterilization processes (checked 13 November 2026)
- ISO 14937:2009, Sterilization of health care products, general requirements for characterization of a sterilizing agent and the development, validation and routine control of a sterilization process (checked 13 November 2026)
- Centers for Disease Control and Prevention, Guideline for Disinfection and Sterilization in Healthcare Facilities, healthcare equipment (checked 13 November 2026)
- Centers for Disease Control and Prevention, same guideline, executive summary (checked 13 November 2026)
- Public Health Ontario, Provincial Infectious Diseases Advisory Committee, environmental cleaning guidance, full document (checked 13 November 2026)
- Public Health Ontario, Infection Prevention and Control topic index (checked 13 November 2026)
Auditing the workflow? The sterilization compliance self-check walks through the same steps an assessor follows, including the drying and inspection stage that most paper records skip.
Writing the SOP? The downloadable SOP templates include a reprocessing sheet with a drying and inspection line, so the step is signed rather than assumed.
Not sure how this applies to your own setup? Ask a sterilization compliance specialist — you’ll get a written answer specific to your equipment and province, with the regulation or standard cited.
Related Reading
- How to Cut and Seal Sterilization Rolls
- ISO 11607 Pouch Sealing for Dental Instruments: Seam Width and Validation
- Pouch Overfill and Expansion Space: How Full Is Too Full
- Pouch Sealer Validation Records: Temperature, Pressure and Seal Integrity
Frequently Asked Questions
Why must instruments be dry before packaging?
Because steam sterilization works by contact with saturated steam, and water already sitting on a surface blocks that contact. A droplet on a hinge or in a lumen creates a cooler, wetter zone that reaches temperature more slowly than the rest of the load. The result can be a cycle that looks correct on the chart and still leaves an instrument that was not exposed to the conditions the process is validated for.
Is a quick shake and a paper towel enough?
Only for flat surfaces with no hinge and no matte finish. A paper towel sheds fibre, which is a residue on the instrument and a particulate inside the pack. A shake moves water from the visible surface into the hinge, the ratchet and the box lock, which is where it does the most harm.
Can I use the clinic's compressed air line?
Only if the air meets a stated purity class. Workshop air carries oil aerosol and particulate from the compressor, and blowing oil onto a cleaned instrument is worse than leaving it wet. If compressed air is used at all, specify the purity class to ISO 8573-1 and fit a point-of-use filter, and keep the nozzle away from bearings that are lubricated later.
What does the washer-disinfector drying stage do?
Under ISO 15883-1 and ISO 15883-2, a washer-disinfector is specified, tested and validated as a process, and drying is part of that process rather than an optional extra. Thermal disinfection leaves the load hot, so much of the water flashes off inside the chamber. What the chamber cannot reach is the inside of a narrow lumen or the gap in a closed box lock, which is why the manual check still exists.
How long should instruments air-dry?
Time is the wrong unit. Dryness is a condition, not a duration: a rack in a warm, ventilated reprocessing room dries faster than a rack in a closed cabinet, and a hinged instrument takes longer than a flat one. Write the check, not the clock, into the SOP, and let the check decide when the instrument is ready.
Should instruments be dried before or after lubrication?
Lubrication follows drying, never precedes it. Instrument lubricant applied to a wet surface traps water under the film, and the trapped water is what corrodes a hinge. Manufacturer processing information, required under ISO 17664-1, states the order the makers expect; where it is silent, dry first, then lubricate only the points the maker names.
What is the difference between a wet pack and a damp instrument?
A wet pack is visible moisture inside a sealed pouch after the cycle, and it invalidates the pack. A damp instrument is one that went into the pouch with water still on it. The second causes the first, but they are recorded differently: the first is a load rejection, the second is a step that was skipped.
Does the pouch type change the drying requirement?
It changes how forgiving the packaging is. Paper-film pouches pass vapour and are less prone to trapping condensate than a film-only system, which is one reason the paper side faces the instrument. ISO 11607-1 sets the requirements for the sterile barrier system, and ISO 11607-2 requires the sealing process to be validated, so the pouch and the seal are a specification rather than a stationery choice.
Last updated: November 2026. CliniEco Medical is a licensed medical device establishment (MDEL #35334).