A batch of poured plates that grows colonies after a sterility check is one of the more expensive failures in a small laboratory, because the whole batch, the pour, the incubation time and the investigation all land in the same week. This guide separates the four things that produce that result — an under-processed load, an over-processed load, a contaminated pour, and a plate that was never sterile to begin with — and sets out the cycle, the record and the check that tell them apart. The load label that stays legible through the cycle is the autoclave indicator tape, 3-roll set, and the part that decides whether the batch is released is the record, not the tape colour.
Quick facts
- ISO 11133:2014 covers the preparation, production, storage and performance testing of culture media; CLSI M22 covers quality control of commercially prepared media.
- ISO 17665:2024 is the moist heat sterilization standard, and it treats the load — not the chamber — as the thing being validated.
- Agar is damaged by heat as well as sterilized by it: over-processing drops pH and gel strength, and a plate that will not set is a process failure even when it is sterile.
- The same cycle time that sterilizes 100 mL in a flask does not necessarily sterilize 1 L in the same flask, because the liquid at the centre of the volume lags the chamber.
- A published 2026 study had to establish autoclave conditions specifically for disaccharide-containing liquid media, which is a reminder that the cycle is medium-specific rather than universal (J Microbiol Methods).
- A sterility check that fails can be a sterilization failure, a pour failure or a handling failure, and the three are separated by what grew and where it grew.
What does a failed sterility check actually tell you?
A sterility check asks one question: does this batch, incubated under the conditions the medium supports, produce growth? A positive result says the answer is yes; it does not say why. The diagnosis comes from the pattern.
Three patterns cover most failures. Growth across most or all plates points at the sterilization step or at the pour, because a handling error usually contaminates a few plates rather than the batch. Growth in one or two plates, often at the edge or on the lid, points at handling after the pour. Growth in the poured plates but not in the flask points at the pour, the bench or the plates themselves, since the same liquid was sterile in its container.
The fourth pattern is the one that costs the most time: no growth at all in the sterility check, and growth later in use. That is not a sterilization failure. It is a plate that was sterile and then contaminated in storage or in handling, and the investigation belongs in the incubator and the fridge rather than in the autoclave.
Which cycle parameters actually sterilize a liquid load?
Moist heat sterilization works through saturated steam at a temperature and a holding time; ISO 17665:2024 sets out the requirements for the process and, importantly, for its validation. The familiar 121 °C for 15 minutes is an operating point rather than a fixed requirement, because the temperature that matters is the temperature of the load, and the load reaches it after the chamber does.
Three variables move that lag. Volume: a larger volume has a longer heat-up time and a cooler centre. Container geometry: a narrow-necked flask heats more slowly than a wide tray, and a screw cap that is fully tight can prevent steam contact. Load configuration: flasks stacked against each other create a cold pocket that the chamber probe may not see.
That is why a laboratory that has validated a 500 mL load cannot simply double the volume and keep the time. The 2026 study cited above is a worked example: disaccharide-containing media degrade under extended heat, so the authors established autoclave conditions for that family rather than assuming a general cycle would do (J Microbiol Methods). The same logic applies to any medium with a heat-sensitive component.
What does over-processing do to agar?
Over-processing is the failure that looks like success. The load is sterile, the plates set, and the medium still performs poorly: pH has drifted, selectivity has changed, and colonies that should be easy to read are not.
Two mechanisms matter. Agar itself hydrolyses under prolonged heat and low pH, which reduces gel strength and can leave a soft or weepy plate. Sugars and other heat-labile components caramelise or degrade, which shifts colour and can change the growth-supporting properties of the medium. A plate that fails to set after a longer cycle is showing the same problem as a plate that supports weak growth: the process was too aggressive, not too short.
This is where the brand and lot of the dehydrated medium enter the equation. A 2020 study that compared Mueller-Hinton agar from 21 brands found measurable differences between them (J Clin Microbiol), and a 2024 study showed that agar depth in the plate affects disk diffusion results (J Clin Microbiol). Both findings point the same way for a sterility investigation: the medium and the pour are variables, not constants.
How do you tell a sterilization failure from a handling failure?
| What you see | Most likely cause | What to check first |
|---|---|---|
| Growth in most plates across a batch, including the first poured | Under-processed load or contaminated bulk medium | Load configuration and volume against the validated cycle; chamber temperature record; whether the flask cap was vented |
| Growth in a few plates, often at the lid or the rim | Contamination during the pour or from the bench | Bench and hand hygiene, plate drying position, lid handling, room air movement |
| Plates that set soft, weep, or darken | Over-processing or pH drift | Cycle time and temperature against the medium's instructions; pH after sterilization |
| No growth in the sterility check, growth in use | Storage or handling after release | Fridge temperature record, plate age, sealing, condensation on the lid |
| Growth in the poured plates but not in the flask | Pour, plates or bench | Sterility of the plates themselves, pour technique, drying |
| Growth in the flask and in the plates | Sterilization or the bulk medium | Cycle validation, load map, medium lot, water used to make the medium |
The table is a starting point, not a diagnosis, and the reason is that the same visible result can come from two different failures. That is why the record has to carry the load configuration: without it, the investigation restarts from zero every time.
What should the record carry for every media load?
A media sterilization record that survives an inspection has six fields, and all six are cheap to capture at the time and expensive to reconstruct later.
| Field | What it captures | Why it is needed |
|---|---|---|
| Load identifier and contents | What was sterilized, in which containers, at what volumes | Defines the load that the cycle was validated for |
| Cycle parameters | Temperature, time, pressure, and the cycle selected | Shows that the process matched the validated one |
| Cycle record or printout | The chamber trace for that load | Shows the chamber reached and held the parameters |
| Chemical indicator | The class used and the result | Shows the load was exposed, not just the chamber |
| Biological indicator, where used | Organism, lot, incubation, result, read time | Provides the biological evidence for the cycle |
| Medium details | Medium name, lot, pH before and after, plates poured | Ties the batch to the material that was processed |
Two of those fields are routinely omitted and both matter. The volumes and containers are what make the cycle reproducible; without them the next load is an experiment. The post-sterilization pH is the earliest sign that the cycle was too hot for too long, and it is measured anyway when the medium is prepared.
Do you need a biological indicator for a media load?
Not always, and the reason is that a sterility check is itself a biological test. A poured plate that shows no growth after incubation has demonstrated that the load was sterile under the conditions of the check. What the check does not demonstrate is that the sterilization process is under control, because it tests the outcome rather than the process.
That distinction decides when a biological indicator earns its place. Where the load is a large volume, a dense configuration or a medium that cannot be held for a full incubation before use, an indicator run with the load adds process evidence. ISO 11138-1:2017 sets out the requirements for the indicators themselves, including the population and resistance characteristics that make the result meaningful (ISO 11138-1:2017). Where a laboratory runs a sterility check on every batch, the indicator is a periodic process check rather than a batch test.
The third element is bioburden. ISO 11737-1:2018 covers the estimation of bioburden on products, and the same thinking applies to a bulk medium: knowing how contaminated the raw material is tells you how much the process has to achieve (ISO 11737-1:2018).
How does a Canadian lab document this against US practice?
The technical content is largely shared: ISO 11133:2014 for media preparation and performance testing, CLSI M22 for quality control of prepared media, and CLSI M07 and M02 for the susceptibility methods that depend on the media. The difference sits in the paperwork that surrounds them.
| Question | Canada | United States |
|---|---|---|
| Media preparation standard | ISO 11133:2014 with CLSI M22 as the quality-control reference | CLSI M22 with ISO 11133 used where the laboratory's quality system cites it |
| Sterilization process standard | ISO 17665:2024 | ISO 17665:2024, with AAMI guidance used in hospital settings |
| Indicator requirements | ISO 11138-1:2017 | ISO 11138-1:2017 |
| Who inspects the record | The accreditation body the laboratory is assessed against, plus provincial requirements | Accreditation and, where relevant, federal programme requirements |
| Practical consequence for a buyer | The standard number belongs in the SOP, and the SOP is what gets assessed | The same, with the method standard number expected next to the medium |
The practical point for a laboratory is that the standard numbers are the same on both sides of the border, so a method transferred from a US site does not need re-writing — it needs the local SOP wrapper and the local record.
Media preparation and plate pouring consume gloves faster than any other bench task: nitrile examination gloves, 3.5 mil, 1,000 per case, and the load labels come from the autoclave tape set. Laboratory purchasing runs through the wholesale programme, and the monitoring products that support the same cycle sit under sterilization monitoring and the sterilization compliance hub. Reselling? become a distributor.
For the media side of the same question, whether to pour plates in-house or buy them prepared sets out the cost and control trade-off, and the media rules comparison covers the standard numbers behind the media themselves. When a positive biological indicator is the finding rather than a contaminated plate, the sequence is the one described in what to do with a load after a positive biological indicator.
Build the batch record before the next media run: the printable cycle and load log carries the fields above on one sheet, per load, with a line for the chemical and biological result.
If the laboratory would rather generate the sheet than store a pad of them, the log generator on the same page builds a load sheet from the sterilizer and the container types actually in use.
Where a media cycle sits inside an accreditation question, the consultation desk answers in writing, specific to the sterilizer and the province, with the clause it relies on cited — no account and no sign-up needed.
Sources
All links checked 23 October 2026.
- ISO 11133:2014, Microbiology — Preparation, production, storage and performance testing of culture media
- ISO 17665:2024, Sterilization of health care products — Moist heat
- ISO 11138-1:2017, Biological indicators for sterilization processes
- ISO 11737-1:2018, Sterilization of health care products — Microbiological methods
- CLSI M22: quality control of commercially prepared culture media
- CLSI M07: methods for dilution antimicrobial susceptibility tests
- CLSI M02: performance standards for antimicrobial disk susceptibility tests
- Establishment of autoclave conditions for disaccharide-containing liquid media
- Agar depth and disk diffusion performance
- Comparison of Mueller-Hinton agar from 21 brands
- Geobacillus stearothermophilus and the autoclave spore test
- CliniEco Medical: sterilization compliance hub
Related reading
- Pouring agar plates in-house or buying them prepared: a decision guide
- Tryptic soy agar plates in Canada versus the United States: which media rules apply
- What to do with a load after a positive biological indicator
Frequently Asked Questions
Why did my agar plates grow contamination after autoclaving?
The batch pattern tells you where to look. Growth across most plates points at the sterilization step or the bulk medium; growth in one or two plates points at the pour or handling; growth in the poured plates but not the flask points at the plates, the bench or the pour.
Does a longer cycle make a failed load safe?
No. Extending the cycle adds heat damage to the medium without fixing a load configuration that prevents steam contact. Agar hydrolyses, pH drifts and gel strength falls, so the plates may be sterile and unusable at the same time.
Can I sterilize 1 L in the same time as 500 mL?
Not without validating it. The centre of a larger volume lags the chamber, so the load reaches the holding temperature later. A validated cycle is tied to the volume, the container and the load arrangement, which is why those fields belong in the record.
Do I need a biological indicator for every media batch?
Not necessarily. A sterility check on the poured plates is itself a biological test of the batch. A biological indicator adds process evidence for large volumes, dense loads, or media that cannot wait for a full incubation, and ISO 11138-1:2017 sets the requirements for the indicator itself.
What causes a plate that will not set?
Over-processing or the wrong pH. Prolonged heat at low pH hydrolyses agar and reduces gel strength, and it also degrades heat-sensitive components. Check the cycle against the medium manufacturer's instructions, then check the pH after sterilization.
Which standard covers the sterility check itself?
The check is a quality-control step on prepared media, which is where CLSI M22 applies, with ISO 11133:2014 covering preparation, production, storage and performance testing of the medium. The sterilization process that produced the medium is covered by ISO 17665:2024.
CliniEco Medical supplies sterilization monitoring and infection-control consumables in Canada under MDEL #35334. This article describes published standards and process practice; it is not a substitute for the validated cycle and written procedure of the laboratory concerned.