Which Standards Apply to Adult Pull-On Diapers in Alberta Clinics?

Adult underpads stacked in a case, used as bed protection alongside pull-on briefs

Which Standards Apply to Adult Pull-On Diapers in Alberta Clinics?

An Edmonton care home takes delivery of four cases on a Monday and by Wednesday the supply room has three opened. Nobody can say which standard the briefs were bought against, and the resident who needs the heaviest core is wearing the daytime product because the night product ran out. The standard question and the stocking question are the same question asked twice.

Start with the product. Adult pull-on diapers in a 120-count case arrive as six packs of twenty, sold by the case, and the format is the point: no tabs, a stretch waistband that a resident can pull up unaided, and leak guards at the leg opening.

What follows is the standard stack behind that pack — which editions are current in 2026, what an absorbency figure actually measures, and the Alberta funding rule that decides which products a clinic can hand over at all.

Which standards apply to an adult pull-on diaper in Alberta?

Fewer than suppliers imply, and two of the six are withdrawn. The table below is the whole stack as it stands after February 2026.

Standard What it covers Status in November 2026
ISO 15621:2026 General guidelines for evaluating absorbent incontinence products for urine, faeces or both Current, published 19 February 2026
ISO 15621:2017 The previous edition of the same guidelines Withdrawn 19 February 2026
ISO 11948-1:1996 Whole-product testing: absorption capacity of the absorbent core Current, confirmed 7 June 2023
ISO 11948-2:1998 Short-time liquid release under light incontinence and low pressure Withdrawn 15 December 2003
ISO 9949-1:1993 and 9949-2:1993 Vocabulary for conditions and for product terms Both withdrawn 2 June 2021
ISO 17190-1, -5 and -9:2020 Tests on the polyacrylate superabsorbent powder itself Current, Part 1 under revision
ISO 10993-1:2025 and 10993-23:2021 Biological evaluation, including irritation testing Current
ISO 15223-1:2021 Symbols used on the pack and the instructions Current

The practical reading is uncomfortable. The vocabulary standards that defined what "brief", "pull-on" and "pad" mean in a technical document were withdrawn in June 2021, so a supplier citing them is citing history. The leakage test that many older specification sheets still name, ISO 11948-2, was withdrawn in December 2003.

What changed when ISO 15621 was replaced in February 2026?

The core evaluation document was replaced on 19 February 2026, and the title changed with it. The 2017 edition was called absorbent incontinence aids for urine and/or faeces. The 2026 edition is called absorbent incontinence products for urine, faeces, or both, and its scope is written for evaluating products for adults and children.

That change of wording is not cosmetic. The 2026 document positions itself as a context for procedures described in other International Standards and in published testing procedures, which is a different job from setting a single pass mark. It tells a buyer what to evaluate and how the pieces fit together; it does not turn an absorbency number into a regulated claim.

For an Alberta buyer the consequence is a documentation check rather than a product change. Ask which edition the specification was written against. A pack whose technical file says ISO 15621:2017 predates the current document by months, and a supplier who cannot name an edition at all is not working to a standard.

Adult pull-on diaper shown without tabs, with an elastic waistband and leak guards

What does the mL number on the pack actually measure?

It measures the absorbent core, under test conditions, and it is not a statement about how much a resident will pass.

ISO 11948-1:1996 is titled whole-product testing, yet its scope is specific: it gives a method for determining the absorption capacity of the absorbent core of body-worn urine-absorbing aids. That is the figure a marketing team turns into 3,000 mL or 5,000 mL. It is a real measurement, taken on a real product, and it is also a laboratory capacity under a defined procedure, not a working volume in a bed at three in the morning.

The powder underneath that core has its own standards. ISO 17190-1:2020 sets the pH test for polyacrylate superabsorbent powder, ISO 17190-5:2020 sets the free swell capacity in saline, and ISO 17190-9:2020 sets the apparent density. All three describe the material a manufacturer buys, not the brief a resident wears, and Part 1 is under revision, with work in development on a replacement.

Three statements can therefore be true at once. Two products can both be tested to ISO 11948-1 and still behave differently in use. A higher number does not automatically mean a better night. And a product with no method named behind its number is the one to leave on the shelf.

Which Alberta rule decides who pays for a pull-on?

Alberta has a provincial funding programme, and it does more to shape what a clinic stocks than any product standard.

Alberta Aids to Daily Living is available to Alberta residents with a long-term disability, a chronic illness or a terminal illness. The route in is a clinical assessment by an AADL authorizer — a registered nurse, occupational therapist or physiotherapist approved by the programme — who determines the need and identifies the equipment and supplies. Once authorized, an AADL-approved vendor supplies the benefit and collects the client share.

Two lists decide the purchase. Incontinence supplies appear on the programme's benefit list, described as diapers and catheters. Products are managed through approved product lists, and the medical-surgical list covering ostomy, catheters and incontinence is Section M. A product that is not on that list cannot be supplied through the programme, however suitable it is clinically.

The cost share is worth knowing because residents ask at the counter. Most benefits carry a 25 per cent client share, capped at $500 per family per benefit year, which runs from 1 July to 30 June. Clients can be exempt on income grounds, with thresholds published by the programme, and recipients of Income Support, AISH, the Alberta Disability Assistance Program or Alberta Adult Health Benefits can ask AADL directly. An upgrade to a higher specification is charged separately and does not count against the cap.

Adult underpads stacked in a case, used as bed protection alongside pull-on briefs

Which standards cover skin contact and labelling?

Two documents, and both are about the product rather than the packaging. ISO 10993-1:2025 sets the biological evaluation framework, so a material in contact with skin is assessed within a risk management process rather than in isolation. ISO 10993-23:2021 supplies the irritation test method, and was confirmed in June 2026.

Labelling follows ISO 15223-1:2021, which standardises the symbols a pack can print instead of sentences. For an Alberta buyer the useful check is that the symbol set matches the written instructions, in both official languages, and that the size range on the pack matches the measurement the care staff actually take.

The general safety duty sits outside the standards. The Canada Consumer Product Safety Act prohibits supplying a consumer product that is a danger to health or safety, and a pack of briefs sold through a retail aisle is a consumer product in a way that a case shipped to a licensed continuing care home is not. In continuing care, the accommodation framework under the Continuing Care Act is what a director of care is inspected against.

How do you size and count pull-ons for a clinic or care home?

Measure the resident, then do the case arithmetic. Pull-on sizing runs on waist and hip measurement rather than on the absorbency line, and a resident who sits between two sizes is usually better served by the larger one, because the leg opening is what leaks.

Product line Stated capacity Case Where it fits
Pull-on, maximum Maximum core in the pull-on range 120 briefs, six packs of twenty Walking residents, overnight use where volume is moderate
Daytime brief 3,000 mL 120-count case Day plans, frequent changes
Mid-range brief 4,000 mL, wetness indicator, leak guards 120-count case Mixed mobility, staff-led changes
Overnight brief 5,000 mL 120-count case Flooding overnight, bed-bound residents

The counts are what drive the order. Daytime briefs in a 120-count case suit a home running a fixed daytime schedule, while overnight briefs at 5,000 mL belong on the night round. Heavy absorbency underpads, 30×36 inches do the bed protection that a pull-on cannot, and a clinic that stocks all three is buying a system rather than a product.

Six changes a resident per day is the working figure, so 120 briefs is twenty resident-days. Twenty residents at that rate is 120 briefs a day, which is one case a day, which is seven cases a week, which is the number that belongs on the reorder card.

What should an Alberta buyer check before ordering?

Five checks, and the first two decide the rest:

  • The standard edition named on the specification, with its year
  • Whether the product code appears on the AADL Section M approved product list, if the home serves AADL clients
  • The absorbency figure and the test method behind it, not the figure alone
  • Waist and hip range against the residents actually being fitted
  • Case count and pack count, since a 120-count case and a 60-count case are different reorder cycles

Running a long-term care home, a retirement residence or a home care programme in Alberta? long-term care and retirement home supplies covers the incontinence lines we stock. Ordering for a clinic, lab or care home? Wholesale and multi-site ordering covers case pricing and account setup, and the B2B wholesale collection lists the lines stocked for institutional buyers. Reselling? become a distributor.

References

  1. ISO 15621:2026 — Absorbent incontinence products for urine, faeces, or both: general guidelines on evaluation — Genorma (ISO/TC 173/SC 3) (checked 3 November 2026)
  2. ISO 15621:2017 — Absorbent incontinence aids for urine and/or faeces: general guidelines on evaluation (withdrawn 19 February 2026) — Genorma (ISO/TC 173/SC 3) (checked 3 November 2026)
  3. ISO 11948-1:1996 — Urine-absorbing aids, Part 1: whole-product testing — Genorma (ISO/TC 173/SC 3) (checked 3 November 2026)
  4. ISO 11948-2:1998 — Determination of short-time liquid release under conditions of light incontinence and low pressure (withdrawn 15 December 2003) — Genorma (ISO/TC 173/SC 3) (checked 3 November 2026)
  5. ISO 9949-1:1993 — Urine absorbing aids, vocabulary, Part 1: conditions of urinary incontinence (withdrawn 2 June 2021) — Genorma (ISO/TC 173/SC 3) (checked 3 November 2026)
  6. ISO 9949-2:1993 — Urine absorbing aids, vocabulary, Part 2: product terms (withdrawn 2 June 2021) — Genorma (ISO/TC 173/SC 3) (checked 3 November 2026)
  7. ISO 17190-1:2020 — Polyacrylate superabsorbent powders, Part 1: determination of pH — Genorma (ISO/TC 173/SC 3) (checked 3 November 2026)
  8. ISO 17190-5:2020 — Polyacrylate superabsorbent powders, Part 5: free swell capacity in saline — Genorma (ISO/TC 173/SC 3) (checked 3 November 2026)
  9. ISO 17190-9:2020 — Polyacrylate superabsorbent powders, Part 9: apparent density — Genorma (ISO/TC 173/SC 3) (checked 3 November 2026)
  10. ISO 10993-1:2025 — Biological evaluation of medical devices, Part 1: Requirements and general principles for the evaluation of biological safety within a risk management process — Genorma (ISO/TC 194) (checked 3 November 2026)
  11. ISO 10993-23:2021 — Biological evaluation of medical devices, Part 23: tests for irritation — Genorma (ISO/TC 194) (checked 3 November 2026)
  12. ISO 15223-1:2021 — Medical devices: symbols used with information supplied by the manufacturer — Genorma (ISO/TC 210) (checked 3 November 2026)
  13. Alberta Aids to Daily Living (AADL) — programme entry point and authorizer assessment — Government of Alberta (checked 3 November 2026)
  14. AADL benefits covered — incontinence supplies listed as a benefit — Government of Alberta (checked 3 November 2026)
  15. AADL cost sharing — 25 per cent to a $500 annual maximum, and exemption thresholds — Government of Alberta (checked 3 November 2026)
  16. AADL program manual and product lists — Section M medical-surgical and incontinence list — Government of Alberta (checked 3 November 2026)
  17. Continuing Care Act, RSA 2000, c C-26.3 — Alberta King's Printer (checked 3 November 2026)
  18. Canada Consumer Product Safety Act, S.C. 2010, c. 21 — Department of Justice Canada (checked 3 November 2026)

Printable companion: the free log and template centre includes a supply and rotation sheet, so the product code, the case lot and the date a resident started on a new size sit on one page instead of three.

Changes per resident per day is the number that sets the order, and the clinic supply and cost planner turns that into cases per month, which is what a case price should be measured against.

Related Reading

Frequently Asked Questions

Which standard applies to adult pull-on diapers today?

ISO 15621:2026, published on 19 February 2026, is the current general guidelines document for evaluating absorbent incontinence products for urine, faeces or both, for adults and children. The 2017 edition of the same standard was withdrawn on the same day. So a specification sheet that cites ISO 15621:2017 is quoting a document that was replaced in February 2026.

Is 5,000 mL the amount one resident can void?

No, and the difference matters for procurement. ISO 11948-1:1996 gives a method for determining the absorption capacity of the absorbent core of body-worn urine-absorbing aids. That is a property of the core measured under test conditions, not a promise about how much a resident will pass in a night, and it says nothing about how the product fits.

Are the mL ratings on different brands comparable?

Only if the same method is quoted. A figure is meaningful when the pack or specification names the test behind it, and the only current whole-product document in the family is ISO 11948-1:1996, confirmed in 2023. Two brands that both say "tested to ISO 11948-1" can be compared; two brands that print a number with no method cannot.

Does AADL cover adult diapers in Alberta?

Yes. Incontinence supplies, described in the programme's benefit list as diapers and catheters, are an AADL benefit. The resident has to be assessed by an AADL authorizer, and the product has to be on the Section M medical-surgical and incontinence approved product list to be supplied through the programme.

What does an AADL client pay towards a case of pull-ons?

Most benefits carry a 25 per cent client share, capped at $500 per family per benefit year, which runs from 1 July to 30 June. Low-income clients may be exempt, and recipients of Income Support, AISH, the Alberta Disability Assistance Program or Alberta Adult Health Benefits can ask AADL about exemption directly.

Does a clinic need approval to supply AADL clients?

Yes. AADL benefits are provided through AADL-approved vendors, and a client is offered up to three approved vendors after assessment. A clinic that wants to serve those clients needs to be on the vendor list and to stock product codes that appear on the Section M approved product list.

Is a pull-on or a taped brief the right format?

Pull-on suits a resident who still walks and dresses, because it goes on like underwear with no tabs to line up. A taped brief suits a resident who is bed-bound or where staff do every change, because the tabs allow a snug fit lying down and a re-check without removing the product. Many homes stock both and split by resident.

How many briefs does one resident use in a day?

Six changes a day is the working figure used for planning, which makes a 120-count case about twenty resident-days. A home running twenty residents at six changes each therefore needs six cases for a single day of cover, so the reorder point should be set in cases per week rather than in packs.

Last updated: October 2026. CliniEco Medical is a licensed medical device establishment (MDEL #35334).

Already working with clinics? Become a regional representative.