What Is a PCD and When Does a Clinic Need One?

A PCD, or process challenge device, is a holder that places an indicator where steam is hardest to reach inside the sterilizer, so a pass means the difficult part of the load was actually penetrated. In practice a clinic meets one in two forms: a commercial challenge pack such as a Bowie-Dick type, or a routine load that is deliberately arranged with the indicator inside the most densely packed pouch. The CliniEco 24-hour biological indicator, 25-pack — three self-contained indicators24-hour biological indicators, 25 per pack are what most Ontario clinics place inside that challenge position for the daily test.

What does PCD stand for and what does it do?

PCD stands for process challenge device. It is a fixture, not a product category: anything that resists steam penetration in a defined, repeatable way and holds an indicator at the end of that resistance. Its job is to make a difficult load look the same on every cycle, so a failure is visible rather than hidden behind an easy load.

CliniEco Bowie-Dick test packs for pre-vacuum air removal checks

Standards describe the resistance a PCD must provide so that it represents a worst-case load rather than a convenient one. That is why a commercial challenge pack can be used cycle after cycle as a check, while a routine instrument pouch with an indicator taped to the outside is not a PCD at all.

When does a clinic need a PCD?

You need one whenever the test has to represent the hardest item in the load rather than the easiest. In a dental or clinic setting that means the daily biological indicator test, where the indicator should sit inside the challenge position, and any air-removal check in a pre-vacuum sterilizer, where a Bowie-Dick type pack is the recognised device.

CliniEco 24-hour biological indicators, 25 per pack

A clinic that only ever sterilises a few loose instruments in an open tray is working with a load that is already easy to penetrate, but the test standard does not change: the indicator still has to sit where the steam is challenged, not on the tray lid.

Device What it holds Question it answers
Bowie-Dick type pack Chemical indicator sheet Was air removed and steam penetration even?
Challenge device with a biological indicator Spore strip or capsule Did the cycle kill spores in a hard-to-reach position?
Chemical integrator in a challenge position Class 5 integrator Were all critical parameters reached at that point?
Indicator inside a routine pouch Class 4 indicator Was this pack exposed, not whether the load was sterile

What should go inside a PCD?

A biological indicator, a chemical indicator, or both, depending on what the cycle is being tested for. A biological indicator proves that the cycle killed spores. A chemical integrator shows that the critical parameters were reached, which is a weaker but faster statement. Putting one inside and one outside tells you whether a failure came from the sterilizer or from the packaging.

What should not go inside is a used instrument set that then goes back into the clinical rotation. The challenge device is a test object; once it has been through a cycle with an indicator, the contents are handled as test materials and the pack is rebuilt.

How is a PCD different from a test pack?

A test pack is a specific commercial product, usually single-use and standardised. A PCD is the general idea. A Bowie-Dick pack is therefore a PCD, but not every PCD is a Bowie-Dick pack: a validated challenge device built around a biological indicator is also a PCD, and it answers a different question about the same cycle.

The practical consequence is that the two are not interchangeable in a log. Record which device was used, where it sat in the chamber, and what the indicator reading was, because an auditor will ask for the position as well as the result.

What does an auditor expect to see in the record?

Three things: the cycle identifier, which device was used and where it sat, and the result with the read time. A log that shows a negative result but cannot show where the indicator was placed is a weak log, because it does not prove the test challenged the load.

Keeping the log in one place, filled in at the time of the cycle rather than at the end of the week, is the difference between a record and a reconstruction. The log generator prints the fields in the order an inspection usually asks for them.

Related reading

sterilization monitoring collection; what each indicator proves; what ISO 11138 requires of a rapid-readout indicator; wholesale and multi-site ordering Reselling? become a distributor.

Take the paperwork with you: print the sterilization log sheet, pre-fill a week of cycles with the log generator, or ask a sterilization compliance specialist to review how the records line up with the load sheets.

Frequently Asked Questions

Is a PCD the same as a Bowie-Dick test?

A Bowie-Dick pack is one kind of PCD. A PCD is any validated device that places an indicator where steam penetration is hardest.

Does every cycle need a PCD?

No. The challenge device is used for the monitoring test, not for every load. Routine loads carry indicators in the pack, and the challenge test runs on its own schedule.

Where should the indicator sit in a challenge device?

At the point of greatest resistance inside the device, which is why the device is validated as a unit rather than assembled from whatever is on the shelf.

CliniEco Medical is a licensed medical device establishment (MDEL #35334).

Already working with clinics? Become a regional representative.