What Cleaning Applies to Spirometry and Peak Flow Equipment in American Clinics?

Clear anti-fog PET face shield with black elastic headband on a printed backing card

What Cleaning Applies to Spirometry and Peak Flow Equipment in American Clinics?

A respiratory therapist in an Ohio family practice sets a spirometer on the counter between two patients and asks the question that has no comfortable answer: the guideline says the mouthpiece is single-use, the machine costs five figures, and nobody in the room can point to the sentence that says what happens to the device itself.

There is a sentence, and it is more specific than most clinic policies assume. It also says something that surprises people on first reading: you are not meant to be disinfecting the inside of the machine at all.

What does the CDC require for pulmonary-function testing equipment between patients?

The requirement sits in the CDC's pneumonia guideline, recommendation 9, and it covers both devices a lung function room owns. The first part says not to routinely sterilize or disinfect the internal machinery of pulmonary-function testing machines between uses on different patients. The second part sets the between-patient step: change the mouthpiece of a peak flow meter, or the mouthpiece and filter of a spirometer, between uses on different patients.

Read together, those two sentences describe a design philosophy rather than a disinfection schedule. The machine is treated as a fixed piece of equipment whose working parts do not touch the patient, and the patient interface is treated as a consumable. The clinic's job is to make sure the consumable really is changed and really is a barrier, not to run chemistry through a pneumotachograph.

Handling that change is the moment the procedure meets the supply shelf: the CliniEco Medical nitrile examination gloves, 3.5 mil, 1,000 gloves per case are the gloves that go on for the swap, and a clinic that runs out of them substitutes a bare-handed reach under time pressure.

That is not how the older edition of the same guideline read. The 1997 text required that tubing, connectors, rebreathing valves and mouthpieces be cleaned and then subjected to high-level disinfection or sterilization between uses on different patients. The revision moved the burden from processing to replacement, which is faster, less costly and easier to audit — provided the replacement actually happens.

Why does the Spaulding classification point to high-level disinfection?

Because a mouthpiece contacts mucous membrane, and the classification that most American infection prevention policies are built on puts items in three groups by the tissue they touch. Critical items enter sterile tissue or the vascular system. Semicritical items contact mucous membranes or non-intact skin without penetrating. Noncritical items touch intact skin or the environment.

The required level follows the group. Critical items need sterilization. Semicritical items need, at minimum, high-level disinfection — a process that removes all micro-organisms except bacterial spores. Noncritical items need low-level disinfection. The CDC guideline explains the scheme and then admits its limits: whether an instrument stays in a category can depend on how it is used, and the optimal contact time for high-level disinfection is not defined by one number across professional bodies.

That admission matters for spirometry, because it is the reason the device-specific recommendation exists. When a clinic uses a single-use mouthpiece or a filter, the semicritical item is a disposable and the classification question ends there. When it does not, the mouthpiece, the adapter and any breathing tube that sees secretions are semicritical items that need cleaning followed by high-level disinfection or sterilization between patients, and the machine exterior is a separate, easier job.

Which parts of a spirometer actually contact the patient?

The table below is the one worth pinning to the wall of the lung function room, because most cleaning arguments are really arguments about which row a component belongs in.

CliniEco ASTM Level 3 three-ply surgical mask graphic showing the 250 mask case label

Component Patient contact Category Between patients
Mouthpiece, mouthpiece adapter Mucous membrane Semicritical Replace with a single-use item, or clean and high-level disinfect
Bacterial or viral filter Mucous membrane at the patient end Single-use Replace every patient
Breathing tube or valve near the mouth Secretions Semicritical Replace, or clean and high-level disinfection
Device casing, handle, screen, keyboard Intact skin and hands Noncritical Clean and apply an EPA-registered hospital disinfectant
Internal pneumotach, sensors, tubing inside the box No patient contact Manufacturer service Do not routinely disinfect between patients
Nose clip, if reused Skin Noncritical Clean and low-level disinfect, or issue as single-use

Two rows in that table carry almost all of the real-world risk, and neither is the one people worry about. The filter is the row that gets skipped when a clinic runs late, and the casing is the row that gets wiped with whatever is nearest, which is often not a product registered for the claim being made.

What changes when a disposable mouthpiece or filter is used?

The classification problem disappears, and the audit trail simplifies to a stock question. If a spirometer is used only with a single-use mouthpiece and filter, the semicritical item never gets reused, so there is no high-level disinfection step to validate, no contact time to record and no test strip to store. What remains is a documented assurance that the consumable was changed and that the stock was available.

That is a supply question with a clinical consequence. A filter that runs out in the middle of a clinic day does not produce a processing failure; it produces a decision made under time pressure by whoever is holding the mouthpiece. Keeping the filter and mouthpiece stock at the same par level as the test strips is the least dramatic risk control in the room, and one of the few that can be verified by counting boxes.

How is a peak flow meter handled between patients?

By the same rule, with one practical wrinkle. A peak flow meter is often prescribed to a single patient and lives in their bag, in which case the mouthpiece belongs to that patient and the between-patient rule does not apply. A clinic meter that is used to check several patients a day is a different device in practice, and its mouthpiece changes every time.

When a clinic meter is reused, the meter body is noncritical — it is held in hands, set down on a table, written on — and it is cleaned and disinfected with an EPA-registered hospital disinfectant between uses, following the label contact time. The mouthpiece is the semicritical item. Clinics that hand a patient a meter to take home should not take it back into the clinical stock without deciding, in writing, which of those two rules it is now following.

Does the FDA device class change the cleaning rule?

It does not, and this is a common mix-up worth separating cleanly. Under 21 CFR 868.1840, a diagnostic spirometer is a device used in pulmonary function testing to measure the volume of gas moving in or out of a patient's lungs, and it is placed in Class II with performance standards. That classification governs the device and what it has to achieve in measurement terms. It says nothing about the between-patient step.

Instrument What it governs What it does not govern
21 CFR 868.1840 Device identity and regulatory class Cleaning or disinfection steps
CDC disinfection and sterilization guideline Recommended practice for equipment categories Enforcement or penalties
CDC pneumonia guideline, recommendation 9 Pulmonary-function equipment between patients The disinfectant product to use
ISO 26782:2009 and ISO 23747:2015 Spirometer and peak flow meter performance requirements Reprocessing instructions
ISO 17664-1:2021 Processing information the manufacturer must supply The clinic's own written procedure
EPA registration What a disinfectant may claim on its label How to process a device
29 CFR 1910.132 and 1910.134 Employer duty to supply PPE, respirator fit testing Disinfection method

Read down the middle column and the reason the confusion persists becomes obvious: five different documents each own a piece of the answer, and none of them is the clinic's policy. The policy is what the clinic writes when it has read all five.

Clear anti-fog PET face shield with black elastic headband on a printed backing card

Where does OSHA fit into the workflow?

Two places, both about people rather than devices. Under 29 CFR 1910.132, an employer has to provide personal protective equipment where a hazard is present, and that duty applies to the staff member handling a mouthpiece that has just come out of a patient's mouth. Under 29 CFR 1910.134, if respirators are used at all, the programme requirements — medical evaluation, fit testing, training — apply, and a procedure mask does not satisfy them.

In practice a lung function room needs gloves for handling the interface, a procedure mask for close patient contact, eye protection where splashes are plausible, and a gown if the task involves a patient who cannot control secretions. The CliniEco three-ply ASTM Level 3 mask, 250 per case covers the close-contact part of the test without being mistaken for respiratory protection. The anti-fog PET face shield, individually wrapped, 240 per case is the eye protection that goes on for a coughing patient, and the SMMS 40 gsm Level 2 isolation gown, 50 per pack is for the tasks where a patient cannot keep secretions contained.

What should the written procedure contain?

Six fields, in this order, on one page per device. The device identifier and where it is used. The consumable that goes on it, with the catalogue number. What is replaced and what is cleaned, by component. The disinfectant, its EPA registration number and the label contact time. Who performs the step, and who checks it. The record, and how long it is kept.

Two of those fields are the ones surveys ask about, because they are the ones a clinic cannot reconstruct afterwards. A policy that names a disinfectant by brand but not by registration number cannot be verified against the label. A policy that says "staff clean between patients" without a record is a statement of intent, not a procedure.

What about the machine's internal parts and service intervals?

Leave them to the manufacturer's schedule. Internal pneumotachographs, sensors and the tubing inside the casing are not patient-contacting in normal use, and the guideline's instruction not to routinely disinfect them is a recognition that chemical treatment of precision measurement hardware degrades it. Filters exist precisely so that the measurement path stays clean without chemistry.

What the clinic does owe the device is protection on the outside: keep the casing clean, keep the filter in place, and stop using a machine whose filter was bypassed or wet. A spirometer that has had fluid drawn into its measurement path needs manufacturer service, not a stronger disinfectant, and continuing to test on it produces numbers nobody should act on.

How do you check that the procedure is actually followed?

Three observations, taken a week apart, tell you more than a policy review. Watch whether the filter is removed and discarded in front of the patient rather than after they leave. Look at whether the disinfectant on the counter carries the registration number the procedure names. Ask the person running the test to show you where the record goes.

If any of the three fails, the fix is usually procurement and layout rather than training. Filters within reach of the chair, one disinfectant with a label on the wall, and a log sheet attached to the device cover more ground than a refresher session, and they survive staff turnover.

The pattern that repeats across American clinics is the same one: the rule is known, the consumable is missing at the moment it is needed, and the workaround becomes the procedure. Family practices and multi-site groups that want the surrounding consumables in one place can start from the family practice clinic supply page, which groups the interface stock with the gloves and eye protection the room already uses.

Ordering for a clinic, lab or care home? Wholesale and multi-site ordering covers case pricing and account setup, and the B2B wholesale collection lists the lines stocked for institutional buyers. Reselling? become a distributor.

References

  1. Centers for Disease Control and Prevention, Guideline for Disinfection and Sterilization in Healthcare Facilities (2008, updated 2024) (checked 11 November 2026)
  2. Centers for Disease Control and Prevention, same guideline, Executive Summary (checked 11 November 2026)
  3. Centers for Disease Control and Prevention, same guideline, Healthcare Equipment and the Spaulding classification (checked 11 November 2026)
  4. Centers for Disease Control and Prevention, same guideline, Summary of Recommendations (checked 11 November 2026)
  5. Centers for Disease Control and Prevention, same guideline, Introduction, Methods and Definition of Terms (checked 11 November 2026)
  6. Centers for Disease Control and Prevention, Guidelines for Preventing Health-Care-Associated Pneumonia, 2003, recommendation 9 on pulmonary-function testing equipment (checked 11 November 2026)
  7. Centers for Disease Control and Prevention, Guidelines for Prevention of Nosocomial Pneumonia, 1997, pulmonary function apparatus (checked 11 November 2026)
  8. 21 CFR 868.1840, Diagnostic spirometer, device identification and classification (checked 11 November 2026)
  9. 29 CFR 1910.132, Personal protective equipment, employer duties (checked 11 November 2026)
  10. 29 CFR 1910.134, Respiratory protection, fit testing (checked 11 November 2026)
  11. US Environmental Protection Agency, Selected EPA-registered disinfectants (checked 11 November 2026)
  12. ISO 26782:2009, Spirometers for the measurement of time forced expired volumes (checked 11 November 2026)
  13. ISO 23747:2015, Peak expiratory flow meters (checked 11 November 2026)
  14. ISO 17664-1:2021, Information to be provided by the manufacturer for processing (checked 11 November 2026)
  15. ISO 14971:2019, Application of risk management to medical devices (checked 11 November 2026)
  16. ISO 11135:2014, Ethylene oxide sterilization of health-care products (checked 11 November 2026)
  17. ISO 13485:2016, Medical devices, quality management systems (checked 11 November 2026)
  18. ISO 15223-1:2021, Symbols used with information supplied by the manufacturer (checked 11 November 2026)

Documentation pack: the printable compliance log and checklist library includes equipment processing sheets, so the between-patient step is recorded on paper that a surveyor can follow.

Checking the workflow before the survey? The equipment processing self-check walks the same questions this article covers, device by device, and prints a gap list.

Related Reading

Frequently Asked Questions

Do we have to disinfect the inside of a spirometer between patients?

The CDC's pneumonia guideline answers this directly: do not routinely sterilize or disinfect the internal machinery of pulmonary-function testing machines between uses on different patients. The machinery does not come into contact with the patient, and routine chemical treatment of it adds a chemical exposure and a downtime without an infection-control benefit. What changes between patients is the part that touches the patient.

How often should a spirometry filter be changed?

Between uses on different patients. The same recommendation pairs the two devices: change the mouthpiece of a peak flow meter, or the mouthpiece and filter of a spirometer, between uses on different patients. That is a per-patient rule, not a per-session or per-day rule, and a filter that is visibly soiled or damp is changed immediately regardless of the schedule.

Can a mouthpiece be wiped with alcohol and reused?

Not as a substitute for high-level disinfection. Alcohol is an intermediate-level disinfectant in the CDC's own tables, and an item that contacts mucous membranes sits in the semicritical category, where the minimum is high-level disinfection unless the device is single-use. The practical answer for most clinics is a single-use mouthpiece or filter, which removes the disinfection step altogether.

Is a peak flow meter cleaned the same way as a spirometer?

The patient-contacting part is handled the same way, by replacement. The difference is that a peak flow meter is often a personal device that stays with one patient, in which case the mouthpiece is that patient's own and the between-patient rule does not apply. A clinic meter used for multiple patients is a different situation, and the mouthpiece has to change every time.

Which disinfectant should be used on the outside of the device?

An EPA-registered hospital disinfectant, applied for the contact time printed on the label, on the surfaces a patient or a staff member touches. Following the label is not optional: using a product outside its registered directions shifts the liability to the user. High-level disinfectants are not the right product for these surfaces, and the CDC guideline says so explicitly.

Does a spirometer ever need to be sterilized?

Only if it is used in a way that enters sterile tissue, which puts it in the critical category. A diagnostic spirometer used for routine lung function testing contacts mucous membranes and stays semicritical. Sterilization methods such as ethylene oxide are described in ISO 11135 and are used for heat-sensitive critical devices, not for a mouthpiece that should have been disposable.

Who writes the processing procedure, the manufacturer or the clinic?

Both, in sequence. The manufacturer has to supply processing information for the device, which is what ISO 17664-1:2021 governs. The clinic then turns that information into a local procedure that names the product, the contact time, the person responsible and the record, because a manufacturer's instruction sheet is not an auditable clinic document on its own.

Does the FDA device classification tell us how to clean a spirometer?

No. 21 CFR 868.1840 identifies a diagnostic spirometer as a device that measures the volume of gas moving in or out of a patient's lungs and places it in Class II with performance standards. The classification governs the device and its measurement performance, not the between-patient step, and a clinic that cites the regulation as its cleaning rationale has cited the wrong document.

Last updated: November 2026. CliniEco Medical is a licensed medical device establishment (MDEL #35334).

Already working with clinics? Become a regional representative.