Clinical Sample Concentrators in Canada vs the US: Which Class?

Graduated specimen cup with printed volume markings, of the kind used for sample handling on a laboratory bench

Quick facts

  • A clinical sample concentrator reduces a liquid sample to a smaller volume, or dries it to a residue, so the material that matters can be redissolved at a higher concentration or read by an instrument.
  • In the United States it is a named Class I entry at 21 CFR 862.2310, under its own product code, in the same regulation that also names a thermocycler and a nucleic acid quantitation kit.
  • Canada lists no sample concentrator by name. A general laboratory instrument is a non-invasive device, and Rule 7(1) of Schedule 1 to the Medical Devices Regulations places all other non-invasive devices in Class I.
  • One United States regulation covers three different molecular-biology instruments, so the entry names a family and the product code names the device.
  • The two countries agree on Class I here, and the practical difference is the record a laboratory keeps: a United States buyer tracks the entry, a Canadian buyer tracks the establishment licence of the maker and seller.
  • The entries and rule text quoted here were checked against the openFDA device classification API and the Regulations on 2026-10-10.

A clinical sample concentrator is the instrument a molecular laboratory uses to turn a weak sample into a workable one. A sample that arrives dilute, or an eluate that has to be dried before it can be redissolved, goes into the concentrator and comes back in a smaller volume the next instrument can read. For a laboratory buying one, two questions matter: what the instrument has to clear before it is sold, and what the concentration step needs around it. This article answers the first from both rulebooks and the second from how the step is run.

What is a clinical sample concentrator?

A concentrator removes solvent from a sample without losing the material the laboratory cares about. A centrifugal concentrator spins the sample while drawing a vacuum and applying a little heat, so the solvent evaporates while the sample stays at the bottom of the tube and does not boil over. A vacuum concentrator does the same work with heat and vacuum but relies on a rotor to keep the sample in place, and a freeze dryer removes solvent by sublimation for material that cannot take warmth.

The purpose is the same in each case. A sample that is too dilute to give a reading becomes readable when the material in it is redissolved in a smaller volume, and a sample that has to be stored dry is dried under conditions that preserve it. The instrument holds the temperature and the vacuum steady, because an overshoot damages a protein or a nucleic acid, and that stability is what a laboratory buys.

How does the United States classify a sample concentrator?

The United States files the instrument inside a named family. Regulation 21 CFR 862.2310 is titled "Clinical sample concentrator," and every device inside it is Class I, each under its own product code. The same regulation also names a thermocycler and a nucleic acid quantitation kit, so the entry is broader than its title suggests.

Item United States Canada
Basis of the class Named entry, 21 CFR 862.2310 Rule 7(1), Schedule 1, MDR
Class Class I Class I
Why that class The named entry The instrument is non-invasive laboratory equipment
Market path for the maker Class I, general controls; premarket notification only if the entry is not exempt Class I; the maker keeps an establishment licence and the records the Regulations require
Who may import or sell Establishment registration Establishment licence
What a laboratory keeps The run log and the maintenance record The run log and the maintenance record

A Class I entry is the lowest risk band, and a laboratory instrument reaches the market under general controls. The practical effect for a buyer is that the instrument carries a lighter filing than a diagnostic test kit, and the weight of the requirement sits with the laboratory's own run and maintenance records.

Which devices share the United States entry?

The broad entry is the part a buyer should read closely, because one regulation covers three devices a molecular laboratory buys separately. Each has its own product code inside the rule.

Device inside 21 CFR 862.2310 Product code Class Where it is used
Clinical sample concentrator JJH Class I Sample preparation and drying
Thermocycler OUL Class I Nucleic acid amplification
Nucleic acid quantitation kit PEG Class I Measuring nucleic acid yield

Read together, the rows explain why a purchase order should name the device and its code. A request for "sample preparation equipment" names a family rather than a device, and the code is what ties a unit to the filing the manufacturer holds.

How does Canada classify the same instrument?

Canada reaches the same class from a rule rather than a name. The Medical Devices Regulations do not list a sample concentrator, and the instrument does not contact the patient or enter the body, so it is not an invasive device. It is a non-invasive device, and Rule 7(1) of Schedule 1 places all other non-invasive devices in Class I.

A Class I device is not licensed device by device in Canada. The manufacturer holds an establishment licence and keeps the records the Regulations require, and the seller holds an establishment licence for the activity. A laboratory that buys the instrument records its runs and its maintenance under its own quality system, which for a medical laboratory is audited against ISO 15189 rather than against the device rule.

Do Canada and the United States use the same laboratory standards?

The technical layer is shared. ISO 15189 sets the quality and competence requirements for medical laboratories, and ISO 13485 sets the quality management system a manufacturer of either market works to. A sample concentrated the same way in a Toronto and a Denver laboratory is comparable, and the difference between the two markets is the filing, not the technique.

The point where the two rulebooks diverge is not the instrument but the method. The class of a device does not set a temperature or a vacuum, and a laboratory's own standard operating procedure does. A supplier that quotes a drying condition as a regulated requirement is quoting a laboratory choice it does not own.

Graduated specimen cup with printed volume markings, of the kind used for sample handling on a laboratory bench

What does a laboratory check before it buys a concentrator?

The purchasing decision turns on the sample, not the country. A molecular laboratory that recovers nucleic acid from dilute samples buys a centrifugal concentrator for the speed it reaches a dry pellet and for the recovery it holds. A proteomics or chemistry laboratory buys for the temperature range it can hold without cooking the sample. Both check the same two things: the vacuum the unit pulls and the rotor it takes, because a unit that will not pull a deep vacuum leaves samples wet, and a rotor that does not fit the tube the laboratory uses is a mismatch that stops the run.

A laboratory also has to decide what happens to the rotor. The chamber and the rotor are cleaned between sample sets under the laboratory's own procedure, and the cleaning record belongs with the run log. Keeping the two together is the simple fix that carries across both countries.

Specimen transport bag printed with a biohazard symbol and a specimen wording panel, of the kind used to move samples in a laboratory

Which laboratory consumables does a sample bench restock?

The instrument is one line on a laboratory order that turns over quickly. A sample bench restocks the leak-proof graduated sample cups it uses for specimen handling and the sterile centrifuge tubes it uses to hold prepared material. A laboratory that also runs its own steriliser pairs the sterilization monitoring range with the 24-hour monitoring five-pack. Labs and multi-site groups ordering at case level use the wholesale ordering page, and the B2B wholesale collection lists the lines held for institutional buyers. Reselling? become a distributor.

Sources

  1. 21 CFR 862.2310, Clinical sample concentrator
  2. 21 CFR 862.1675, Blood specimen collection device
  3. 21 CFR 864.4010, General purpose reagent
  4. Medical Devices Regulations, SOR/98-282, full text
  5. openFDA device classification API
  6. ISO 15189:2022, medical laboratories
  7. ISO 13485:2016, medical devices quality management
  8. ISO 14971:2019, risk management for medical devices
  9. ISO 17511:2020, metrological traceability of IVD values
  10. ISO 15197:2013, in vitro diagnostic test systems
  11. Health Canada, medical devices
  12. CCOHS, OSH answers
  13. Public Health Ontario, laboratory services
  14. CLSI, clinical and laboratory standards
  15. WHO, Laboratory biosafety manual
  16. Royal College of Dental Surgeons of Ontario
  17. Canadian Dental Association
  18. AACC, laboratory medicine
  19. eCFR, Title 21, Food and Drugs
  20. Minnesota Department of Health

A record of when the concentrator was last serviced, and what a run pulled, is the part of a sample bench that is hard to rebuild after the fact. The printable instrument run and service log is a blank form with columns for the instrument, the run, the date and the initials of the person who checked it. The run log generator on the same page sizes the form to the number of instruments a laboratory runs. No account and no sign-up are needed to open either one.

Every laboratory is set up differently. Ask a compliance specialist and you will get a written answer specific to your equipment and province, with the regulation or standard it is based on cited.

Related reading

CliniEco Medical supplies eye care, laboratory and dental consumables of the kind described in this article. MDEL #35334. This article is written for optometry, laboratory and procurement professionals and is not legal advice; the class of a device and the records kept by a laboratory belong to the manufacturer and to the requirements that apply to it.

Frequently Asked Questions

Is a clinical sample concentrator a Class I device in the United States?

Yes. A clinical sample concentrator is a named Class I entry at 21 CFR 862.2310, under its own product code inside that regulation.

How does Canada classify a clinical sample concentrator?

Canada lists no sample concentrator by name. A general laboratory instrument is a non-invasive device, and Rule 7(1) of Schedule 1 to the Medical Devices Regulations places all other non-invasive devices in Class I.

What else sits in the United States sample concentrator entry?

21 CFR 862.2310 also names a thermocycler and a nucleic acid quantitation kit, so the entry covers three molecular-biology instruments that a laboratory buys separately, each under its own product code.

What does a sample concentrator do?

It removes solvent from a sample so the material in it can be redissolved at a higher concentration or stored dry, using a vacuum with a little heat and a rotor to keep the sample in place without boiling it over.

Do Canada and the United States use the same laboratory standards?

Both markets build on the shared ISO layer, including ISO 15189 for medical laboratories and ISO 13485 for quality management, so a sample prepared the same way is comparable in either country.

Does the device class set a drying condition?

No. The class of a device does not set a temperature or a vacuum; those come from the laboratory's own standard operating procedure rather than from the device rule.

What should a laboratory record for a concentrator?

Record when the instrument was last serviced and what a run pulled, and keep the cleaning record with the run log so the two cannot be separated.

Already working with clinics? Become a regional representative.