Quick facts
- A pipette is a piston-operated volumetric apparatus, and the reference method for checking it is gravimetric: dispense water, weigh it, convert mass to volume with the correction factors for temperature and evaporation.
- ISO 8655-6:2022 is the gravimetric reference procedure; the test applies to the complete system, which means the tip in use is part of what is being measured.
- Maximum permissible errors are set as a percentage of nominal volume, and they tighten as the volume falls, so a 10 µL pipette is judged against a smaller absolute error than a 1,000 µL pipette.
- In the United States, CLIA requires equipment maintenance and function checks with records at 42 CFR 493.1254; the pipette check is part of that record rather than a separate federal programme.
- In Canada there is no CLIA equivalent, so the requirement arrives through provincial accreditation and the laboratory quality standard the lab is assessed against.
- The standard title, the procedure and the CFR text were read on 2026-10-18.
Pipette calibration is the quietest failure mode in a small laboratory. Nothing stops working when a pipette drifts by four percent; the assay still produces a number, the control still falls inside its range more often than not, and the error shows up months later as a trend nobody can explain. The fix is unglamorous and cheap: weigh the water, compare the volume, write it down. This article covers the method, the interval, the record, and how the Canadian and American requirements differ — alongside the graduated sample cups that a gravimetric bench uses for the water it dispenses.
What does the gravimetric method actually measure?
It measures the volume delivered, not the volume the dial claims. The pipette is set to a nominal volume, a measured mass of water is dispensed into a tared vessel on a balance, and the mass is converted to volume using the density of water at the measured temperature and a correction for evaporation during the weighing. The result is a mean volume and a precision figure across replicates, and both are compared with the maximum permissible error for that nominal volume.
Three details decide whether the number is trustworthy. The balance has to be appropriate for the volume: weighing a 10 µL delivery on a two-decimal balance measures the balance, not the pipette. The waiting time between dispense and reading has to be fixed, because evaporation during a long pause biases the mass downward. And the tip has to be the tip the lab actually uses, because the system under test includes the tip, and a calibration performed with a different tip brand describes a system the lab does not run.
That last point is the one that gets lost in purchasing. A lab that validates a pipette with the tips in the cupboard and then switches to a different tip brand has changed the system without changing the certificate. The certificate still says the pipette is in tolerance; it no longer describes what the bench does.
How do Canada and the United States require pipette checks?
The method is the same on both sides of the border because it comes from the same international standard. The requirement to perform it, and the record that proves it, arrive by different routes.
In the United States, a laboratory holding a CLIA certificate follows 42 CFR 493.1254, which requires equipment to be maintained and function-checked in accordance with the manufacturer's instructions and the laboratory's procedures, with records that show the maintenance and the corrective action taken when a check fails. The pipette check is not named in the regulation; it is an equipment function check, and it belongs in the same record as the centrifuge and the incubator. A laboratory accredited by a private programme also answers to that programme's checklist, which typically states an interval rather than leaving it to the lab.
In Canada, there is no federal equivalent of CLIA. A medical laboratory is licensed or accredited provincially, and in Ontario the accreditation and proficiency testing route runs through IQMH. The quality standard the laboratory is assessed against is ISO 15189, which requires equipment to be calibrated or verified before use and at defined intervals, with records that allow the history of the instrument to be reconstructed. The practical effect is the same obligation with a different auditor.
| Item | Canada | United States |
|---|---|---|
| Federal testing statute | None equivalent to CLIA | CLIA, 42 CFR 493 |
| Requirement source | Provincial accreditation plus ISO 15189 | 42 CFR 493.1254 and accreditor checklist |
| Interval | Set by the laboratory's quality plan and the accreditor | Set by procedure and accreditor checklist |
| Record | Equipment history, calibration or verification, corrective action | Maintenance and function-check record, corrective action |
| Reference method | ISO 8655-6 gravimetric procedure | Same standard |
| Read on | IQMH and ISO material | Cornell LII text, 2026-10-18 |
What interval should a laboratory set?
There is no single number in the standard, and a lab that copies one from another lab is guessing. The defensible approach is risk-based: shorter intervals for pipettes used daily at small volumes, for pipettes that have been dropped or serviced, for pipettes used by several people, and for any pipette that has produced a control result outside its expected range.
Four events should trigger a check regardless of the calendar. After any service or repair. After autoclaving, if the pipette is autoclaved. After a new user is trained on it. And after a change of tip brand or tip lot, because the system under test has changed. A laboratory that records those four triggers alongside a routine interval has a record that answers the question an assessor actually asks: why this interval, for this pipette.
| Volume range | What to check | What to record |
|---|---|---|
| 0.5 to 10 µL | Accuracy and precision at the low, middle and nominal setting | Mean volume, error percent, CV, balance used |
| 20 to 200 µL | Accuracy and precision at nominal and at 10 percent of nominal | Same, plus tip lot |
| 100 to 1,000 µL | Accuracy and precision, with evaporation control | Same, plus water temperature |
| Multichannel | Each channel separately | Per-channel results, not a channel average |
| After service | Full check at all settings | Service date, technician, result |
Do laboratories in Canada and the United States file the same evidence?
The record content converges, because both systems want the same four facts: what was tested, against what limit, with what result, and what was done when it failed. What differs is the wrapper. An American laboratory files the check under its CLIA quality-system record and produces it at survey; a Canadian laboratory files it under its quality manual and produces it at accreditation, with the proficiency testing results that IQMH supplies sitting alongside.
The second difference is who signs. In a CLIA laboratory the record sits inside a defined hierarchy of responsibility with a laboratory director named on the certificate. In a Canadian laboratory the equivalent responsibility is defined by the provincial licensing framework and the quality manual, which usually names a quality manager and a technical supervisor. Neither is better; they are different ways of answering "who knew".
For a small clinic laboratory that runs a few pipettes and no full quality system, the practical answer is to keep one sheet per pipette: the serial number, the date, the method, the balance, the results at each setting, the pass or fail, and the action taken. That sheet is enough to show the check was real, and it costs a few minutes per pipette per interval.
Which consumables does a calibration bench use?
A gravimetric bench needs a stable vessel, a supply of the tips the lab actually runs, and water of known quality. The vessel matters more than it looks: a wide-mouth cup evaporates faster than a narrow one, and an evaporating vessel produces a result that drifts downward across replicates, which reads as poor precision when the pipette is fine.
Ordering for a clinic, lab or care home? Wholesale and multi-site ordering covers case pricing and account setup, and the B2B wholesale collection lists the lines stocked for institutional buyers. Reselling? become a distributor.
The lines that move with a calibration routine are the graduated 90 mL sample cups used as weighing vessels, the sterile 50 mL centrifuge tubes that hold the water and the diluent, and the 15 mL centrifuge tubes for the smaller volumes. The wider clinic supplies collection groups them for one order.
Sources
- ISO 8655-6:2022, gravimetric reference measurement procedure
- ISO, standards catalogue
- 42 CFR 493.1254, equipment maintenance and function checks
- 42 CFR 493.1253, establishment and verification of performance specifications
- 42 CFR 493.1291, standard: test report
- 42 CFR 493.1256, standard: control procedures
- IQMH, proficiency testing overview
- IQMH, proficiency testing catalogue
- CLSI, general laboratory standards
- CLSI, education and training
- Medical Devices Regulations, SOR/98-282
- Health Canada, medical devices
- Public Health Ontario, laboratory and infection control resources
- Public Health Ontario, reprocessing
- openFDA device classification API
- Standards Council of Canada
- CCOHS, OSH answers
- WHO, laboratory quality management
- CSA Group
- Ontario, Healing Arts Radiation Protection Act
Printable pipette check sheet. One sheet per pipette, one row per setting, and the four triggers that force an early check. Print the pipette verification sheet - serial number, balance, water temperature, mean volume, error and pass or fail, on plain paper with no account and no sign-up.
Interval planner. Enter the pipette count and the routine interval and the page lays out the checks across the year, with the service and tip-change triggers flagged. Build a pipette check calendar - printable, and usable as the equipment page of a quality manual.
Ask a compliance specialist. Whether a pipette check belongs in your equipment record or in a separate verification file depends on the standard your laboratory is assessed against. Ask a compliance specialist - written answer specific to your equipment and province, with the regulation or standard it is based on cited.
Related reading
- Micropipettes in Canada vs the US: which class applies
- Pipette tips in Canada vs the US: which device class applies
- P1000 pipette: which volume range and tip colour does your lab need
CliniEco Medical supplies eye care, laboratory and dental consumables of the kind described in this article. Health Canada MDEL #35334. This article is written for optometry, laboratory and dental procurement professionals and is not legal advice; the class of a device and the records a practice keeps belong to the manufacturer and to the requirements that apply to it.
Frequently Asked Questions
What method is used to calibrate a pipette?
The gravimetric method: dispense water, weigh it on a balance suited to the volume, and convert mass to volume using the density at the measured temperature and an evaporation correction. ISO 8655-6:2022 is the reference procedure.
Does the pipette tip have to match the one used in the check?
Yes. ISO 8655-6 tests the complete system, and the tip is part of that system. A check performed with one tip brand does not describe a bench that has switched to another.
How often should a pipette be checked?
Set the interval from risk and record the reasoning. Daily use at small volumes, multiple users and a history of drops justify a shorter interval, and service, autoclaving, a new user or a tip change should trigger a check regardless of the date.
What does CLIA require for pipettes?
42 CFR 493.1254 requires equipment to be maintained and function-checked with records, and corrective action when a check fails. The pipette is treated as laboratory equipment rather than as a separately regulated device.
Is there a CLIA equivalent in Canada?
No. Canadian laboratories answer to provincial licensing and accreditation, with ISO 15189 as the quality standard most are assessed against, and IQMH providing proficiency testing in Ontario.
What should the pipette record contain?
The pipette serial number, the date, the method, the balance used, the water temperature, the mean volume and error at each setting, the pass or fail against the limit, and the action taken when it failed.