How Do You Read a Surgical Mask Box in Canada?
Why the Box Is the Only Label a Clinic Can Audit
A purchase order records what someone intended to buy. The box records what actually arrived. In a clinic that goes through two or three cases of procedure masks a month, those two documents drift apart quietly: a substitution here, a different level there, a carton that says 50 and a shelf label that still says the old supplier.
Inspectors and auditors work from documents, and the label is the least expensive document a clinic owns. It is printed by the manufacturer, it travels with the product, and it can be photographed at receiving in under a minute. This guide walks through what a mask box must carry, what the badges on it actually mean, and which of those items can be verified without a laboratory.
What Must a Mask Box Show Under the Medical Devices Regulations?
Section 21 of the Medical Devices Regulations sets out what no one may import or sell a device without. The list is shorter than most buyers expect:
- The name of the device
- The name and address of the manufacturer
- The identifier of the device
- The control number, in the case of a Class III or IV device
- An indication of what the package contains, if the contents are not obvious
- The word Sterile, if the manufacturer intends the device to be sold sterile
- The expiry date, where the device has one
- The medical conditions, purposes and uses, and performance specifications where they are needed for proper use
- Directions for use
- Any special storage conditions
Two details in that list matter commercially. First, the control number is required for Class III and IV devices, not for Class I. A buyer who has been taught to look for a lot number on every box will find some boxes without one and conclude the product is unlabelled, when the regulation simply does not ask for it in that class. Second, subsection 21(2) adds the test that gets argued about in audits: the information must be legible, permanent and prominent, in terms the intended user understands. A label printed on a glossy panel that smears when a gloved hand touches it fails that test even though every element is technically present.
Which Label Elements Are Missing From Most Boxes?
In practice the gap is rarely the device name. It is the two items that matter six months later: the expiry date, and the storage condition.

A mask box that has no expiry date is not automatically non-compliant, because the requirement applies where the device has one, and the date is set by the manufacturer based on the component with the shortest projected life. What a clinic should object to is inconsistency inside one delivery: a carton with a manufacturing date and a box with no date at all, sold as the same item. That combination leaves the clinic unable to apply first-expired-first-out rotation, and rotation is the only control that prevents a storeroom from aging silently.
| Label element | What it establishes | What to check at receiving |
|---|---|---|
| :-- | :-- | :-- |
| Device name and identifier | That the item matches the purchase order line | Identifier on the box equals the identifier on the invoice |
| Manufacturer name and address | Who is answerable for the design and the label | Address is a real operating site, not a mail drop only |
| Control number | Lot traceability for Class III and IV devices | Lot on the box equals lot on the carton |
| Expiry date | Rotation basis and recall scope | Date exists, is legible, and is not inside three months |
| Word Sterile | That the manufacturer intends a sterile presentation | Wording appears where the product claims to be sterile |
| Directions and intended use | The task the mask was designed and tested for | Wording names clinical use, not general dust masking |
| Storage conditions | Whether heat or humidity voids the claim | Condition matches how the storeroom is actually run |
What Does the ASTM F2100 Badge Actually Prove?
It proves that a named set of laboratory tests was run against a published specification and produced results inside a band. It does not prove that the box in your hand came from the run that was tested, and it does not create a legal obligation on its own. Those are two different kinds of assurance, and conflating them is the most common misreading in clinic purchasing.
ASTM F2100 grades medical face masks into Level 1, Level 2 and Level 3 using five measured properties. The values are what a specification should quote, because they are the only part of the claim a supplier cannot phrase around.
| Measured property | Level 1 | Level 2 | Level 3 |
|---|---|---|---|
| :-- | :-- | :-- | :-- |
| Bacterial filtration efficiency | 95 percent or more | 98 percent or more | 98 percent or more |
| Particle filtration efficiency at 0.1 micrometre | 95 percent or more | 98 percent or more | 98 percent or more |
| Differential pressure, breathing resistance | under 4.0 mm H2O per sq cm | under 5.0 mm H2O per sq cm | under 6.0 mm H2O per sq cm |
| Resistance to synthetic blood | 80 mmHg | 120 mmHg | 160 mmHg |
| Flame spread | Class 1 | Class 1 | Class 1 |
Most Canadian clinics run two boxes of masks side by side: the ASTM Level 3 three-ply masks a procedure pulls from, and a lighter box for reception. The level printed on each decides which room they belong in.
The fourth row is the one that separates a treatment room mask from a procedure mask used where spray or splatter is possible. The third row is the one staff feel: the higher the level, the harder the mask is to breathe through, which is why a clinic that standardises on Level 3 for every task pays twice, once at the box and once in staff discomfort that shortens wear time. Our own explanation of how the F2100 levels map to clinic tasks goes through that trade-off task by task.

Which Symbols Should Staff Recognise?
Most mask boxes carry pictorial symbols rather than sentences, and the meanings are standardised in ISO 15223-1. Three of them decide how a carton is stored and how long it may be kept:
- A single figure with a struck-through 2 means single use only, which is the symbol that settles the question of re-wearing a mask between patients
- A factory symbol with a date means date of manufacture, and it is not the same as the expiry symbol
- A package symbol with a crossed-out sun means keep away from sunlight, which for a storeroom near a window is a real instruction rather than decoration
- A symbol showing an open package with a number of days applies to products whose in-use life starts at opening, and a mask box rarely carries it, which is why clinics set their own rule
A staff member who cannot read three symbols will not read the fourth. Printing one laminated card with the four most common symbols and hanging it where cartons are broken down costs less than one wrong storage decision.
What Do 3-Ply, Medical Grade and BFE Percentages Mean?
Three layers is a construction statement: an outer layer, a filtration layer and an inner layer. It says nothing about what the layers are made of, how the middle layer is charged, or what the finished mask measured. Two masks with identical ply counts can sit at different levels, because the level is set by test results and the ply count is set by the bill of materials.
Medical grade is a marketing phrase with no fixed definition in Canadian device law. When a supplier uses it, the useful follow-up question is which standard the mask was tested to, and at which level, because those two answers can be checked against a report.
A bacterial filtration efficiency figure printed without a test method is a number without a ruler. BFE under ASTM F2100 and BFE under EN 14683 are both measured against a bacterial aerosol, but the two standards differ in method detail and in the scale they grade against, so a 99 percent claim from one is not directly comparable to a 99 percent claim from the other. When a clinic writes its own specification, naming the standard and the level removes the ambiguity in one line.

What Else Sits on a Mask Box That Deserves a Second Look?
Flame spread class is the item buyers skip and auditors occasionally do not. All three F2100 levels call for Class 1 flame spread, so a box that advertises level and omits flame spread has told you half of the story. For clinics working near oxygen, electrosurgery or a spirit burner, that half matters.
Country of manufacture is a sourcing fact, not a quality statement. A mask made in Canada and a mask made elsewhere can both hold Level 2, and a mask made in Canada can also miss the mark if the middle layer is under-specified. The question that produces a useful answer is which plant, which standard edition, and which report.
Barrier against synthetic blood, quoted in mmHg, is the figure to look at when a task involves arterial spray, irrigation or a procedure where fluid can travel. A Level 1 mask at 80 mmHg is a conversation-and-examination mask; using it beside a high-speed handpiece is a task-to-product mismatch that no label wording can rescue.
How Do You Check a Mask Supplier Before Reordering?
Four questions, all answerable in writing, cover most of the risk:
- Which standard and level does the specification name, and which edition of that standard was used for the report
- Which entity is the manufacturer and which is the importer, since the label must name the manufacturer and the two are often different companies
- What lot appears on the carton, and can the supplier trace a delivery date back to it
- What happens if a recall notice names the product, and who contacts the clinic
A supplier that answers all four has a document trail. One that answers the first and gestures at the rest is selling on price alone. Our protection range lists the standard and the level on each product page for exactly this reason, and the masks most clinics settle on are the Level 3 three-ply masks for procedures, the Level 2 made-in-Canada masks for examination and reception work, and the individually wrapped surgical masks where a mask is issued one at a time.
How Do You Record a Mask Lot in Practice?
Three fields on the receiving sheet, filled in at the door: date received, lot from the carton, and the level printed on the box. Everything else can wait until the invoice is matched.
The reason to write the lot rather than photograph the box is that a photograph is not searchable. When a recall notice arrives, the clinic needs to answer one question quickly: is this product in the building, and where. A spreadsheet with a lot column answers it in a filter. A folder of photographs answers it in an afternoon.
If your facility already keeps a receiving log, add the mask level to it. A log that records the lot but not the level cannot show that the room where a procedure happens was stocked with the mask the procedure called for, which is the question an assessor asks when a complaint follows a treatment.
For facilities that want the paper side settled before the next delivery, the clinic supply and cost planner converts monthly patient contacts into boxes and a monthly figure, which makes an over-order visible before it becomes a storeroom of odd lots.
References
- Medical Devices Regulations (SOR/98-282), section 1, interpretation (checked 13 November 2026)
- Medical Devices Regulations (SOR/98-282), section 21, label requirements (checked 13 November 2026)
- Medical Devices Regulations (SOR/98-282), section 44, establishment licence (checked 13 November 2026)
- Medical Devices Regulations (SOR/98-282), section 52, distribution records (checked 13 November 2026)
- Medical Devices Regulations (SOR/98-282), section 59, mandatory problem reporting (checked 13 November 2026)
- Food and Drugs Act (R.S.C., 1985, c. F-27), consolidated text (checked 13 November 2026)
- ASTM F2100-26, Standard specification for performance of materials used in medical face masks (checked 13 November 2026)
- ISO 22609:2004, Clothing for protection against infectious agents, medical face masks, test method for resistance to synthetic blood (checked 13 November 2026)
- EN 14683:2019, Medical face masks, requirements and test methods (checked 13 November 2026)
- ISO 15223-1:2021, Medical devices, symbols to be used with information supplied by the manufacturer (checked 13 November 2026)
- ISO 13485:2016, Medical devices, quality management systems (checked 13 November 2026)
- ISO 10993-1:2025, Biological evaluation of medical devices, evaluation and testing within a risk management process (checked 13 November 2026)
- Health Canada, Medical devices, regulatory overview (checked 13 November 2026)
- Public Health Agency of Canada, Routine Practices and Additional Precautions for Preventing the Transmission of Infection in Health Care (checked 13 November 2026)
- Public Health Ontario, Routine Practices and Additional Precautions (checked 13 November 2026)
- Recalls and safety alerts, searchable database of Canadian product recalls (checked 13 November 2026)
Buying for a facility? Open a wholesale and institutional account for case pricing, purchase-order billing and a named account contact. Reselling? become a distributor.
Building a lot log? The printable compliance log and checklist library carries receiving sheets and lot-tracking pages sized for a clinic front desk, so a box of masks is signed in against the carton rather than remembered.
Reordering against a specification? The bulk quote desk takes a level, a case count and a delivery city and returns a written line-item quote, which is the only form a purchase order can be checked against later.
Related Reading
- ASTM Mask Levels 1-3: PFE and Fluid Resistance for Clinics
- Face Mask Storage and Expiry: Does Quality Degrade Over Time?
- Tie-On or Ear Loop Masks: Which Retention Suits the Room
- Face Mask Levels by Setting: Matching ASTM F2100 to Your Facility
Frequently Asked Questions
Does every face mask sold in Canada need a device licence?
Class I devices are not licensed in Canada, and most procedure masks fall in that class, so a licence number is often absent by design. What a buyer can verify instead is the establishment behind the sale, the label elements required by section 21, and the manufacturer's quality system documentation. A missing licence number is not itself an error; a missing expiry date where one exists, or a missing identifier, is.
Is the ASTM F2100 level printed on the box a legal requirement?
No. The level is a performance claim against a voluntary consensus standard, not a label element created by the Medical Devices Regulations. Section 21 lists the information the label must carry: device name, manufacturer name and address, identifier, contents, expiry date where applicable, intended use, directions, storage conditions and the word Sterile where relevant. A level badge is useful because it is testable, not because it is statutory.
What does Level 2 mean in numbers?
Under ASTM F2100, Level 2 requires bacterial filtration efficiency of at least 98 percent, particle filtration efficiency of at least 98 percent at 0.1 micrometre, differential pressure no higher than 5.0 mm H2O per square centimetre, and resistance to synthetic blood at 120 mmHg. Those four figures are what a specification line should quote, and they travel with the level no matter who prints the box.
Why does the same mask box list both ASTM and EN 14683?
Because the two systems answer the same question with different scales. ASTM F2100 grades masks into Levels 1, 2 and 3 using filtration, breathing resistance, fluid resistance and flame spread. EN 14683 grades into Type I, II and IIR using bacterial filtration efficiency and differential pressure, with Type IIR adding splash resistance. A box carrying both is showing two test reports, not two products.
How long should a clinic keep a mask box?
Keep the carton, or a photograph of its label panel, for as long as the lot may still be in use, then for the retention period your facility applies to receiving records. Section 52 of the Regulations requires distribution records from the seller, and section 59 requires problem reporting, so a clinic that cannot name the lot cannot participate in a recall notice.
Does a bilingual label matter outside Quebec?
Federal device labelling rules ask for information that is legible, permanent and prominent and expressed in terms the intended user understands; they do not impose a nationwide two-language layout. Quebec adds its own language obligations for products sold there. For a clinic ordering nationally, a French panel is a useful signal about the seller's Canadian distribution, not proof of anything else.
What should a clinic check on the carton, not just the box?
The carton carries the case count, the lot and often the only manufacturing date. Two boxes from different lots look identical on the shelf. Write the lot from the carton onto the receiving line, so a later problem can be traced to a delivery date and a purchase order rather than to a brand.
Can a clinic tell filtration from the box alone?
Not reliably. The box states a level, and the level implies test values, but the test report is held by the manufacturer. A clinic that needs the underlying figures should ask for the report covering the lot, along with the standard edition it was tested to, because F2100 has been revised over time and an older report can cite an edition that no longer applies.
Last updated: November 2026. CliniEco Medical is a licensed medical device establishment (MDEL #35334).