An impression tray is the one item on the tray list whose failure shows up as a clinical result rather than a stain. A distorted tray seats unevenly, the material sets in the wrong volume, and the impression comes back with a drag or a void that turns into a remake. Distortion is almost always thermal or mechanical — a plastic tray pushed through a cycle its material was never validated for, or a metal tray whose flange was bent in a basket — and both are avoidable with a rule per material rather than per tray. A heat-seal sterilization roll solves the packaging half of the problem for a bulky item, and a Class 4 self-sealing sterilization pouch covers the smaller sizes.
Which impression trays are reusable, and which are not?
Reuse is a property of the specific tray, not of trays in general. A stainless steel stock tray is a reusable device in most practices and its instruction sheet describes a reprocessing route; a plastic stock tray is frequently a single-use item; a custom tray made in-house from light-cured resin or printed from a design file is usually a single-patient item, and its status depends on the material's own instructions rather than on the fact that it was made in the practice. The device name does not settle the question — the instruction sheet does.
The regulatory framing is consistent on both sides of the border but arrives at it differently. In the United States a preformed impression tray is a named device at 21 CFR 872.6880, described as a metal or plastic device that holds impression material such as alginate; in Canada the classification follows the relationship between tray and material rather than the chemistry of either. Neither point decides reuse; both decide what evidence the manufacturer owes the buyer.
| Tray | Typical material | Usual reuse status | Heat limitation to check | Route |
|---|---|---|---|---|
| Stock, perforated or solid | Stainless steel | Reusable, per instruction sheet | None stated for steam where the sheet validates it | Clean, inspect, package, steam cycle |
| Stock, rim-lock or disposable | Plastic | Often single-use | Maximum temperature stated on the sheet; frequently below a steam cycle | Discard, or disinfect only where the sheet describes reuse |
| Custom tray, laboratory-made | Acrylic resin | Typically single-patient | Heat distortion well below steam temperature for many resins | Clean and disinfect; do not heat-sterilize unless the resin's sheet says so |
| Custom tray, printed | Photopolymer resin | Single-patient | Material-specific; post-cure and temperature limits in the resin documentation | Follow the resin and printer instructions, not the tray convention |
| Triple-tray and dual-arch | Metal or rigid plastic | Reusable if the sheet says so | Same as the material above; larger volume takes longer to dry | Clean, dry thoroughly at the handle joint, then the validated route |
Why does a tray have to be more than cleaned?
A tray goes into the mouth, rests against the mucosa and is removed with set material and saliva on it. That places it in the semi-critical group: devices that contact mucous membrane or non-intact skin, for which cleaning followed by a high-level disinfection or sterilization is the expected minimum. Steam sterilization is the preferred route where the tray tolerates it, because it leaves a package and an indicator that the practice can point at later; high-level disinfection is the fallback for trays whose material cannot take the heat, and it has to be done with a product, concentration and contact time the instruction sheet names.
The distinction is practical rather than academic. A metal tray that is cleaned and put away wet is not semi-critical processing; it is cleaning with a hope attached. A plastic tray that is wiped with a low-level wipe between patients is below the minimum for a semi-critical item regardless of how clean it looks.
What damages a tray before the material does?
Heat is first. Thermoplastic trays soften at a temperature many practices never look up, and a tray that comes out of a 134 °C cycle visibly warped was not defective — it was processed outside its material's limit. The distortion is usually not uniform: one wall moves, the tray still looks like a tray, and the error only appears as a remake three weeks later. This is the single most expensive form of tray damage in a practice, because it is invisible until it has cost a patient a second appointment.
Mechanics come second. Tray flanges bend when trays are stacked in a basket or dropped into a sink, and perforations deform when set material is levered out with a hand instrument instead of being softened and brushed. Chemistry comes third: chlorine-releasing disinfectants pit stainless steel, and repeated exposure to strong disinfectants leaves plastic trays crazed and rough, which affects how impression adhesive behaves on the surface. Water quality after rinsing matters for the same reason it matters on any instrument — residue left to dry becomes scale and, on a metal tray, a corrosion site under the rim.


How should a metal impression tray be processed?
1. Chairside, remove the impression, discard the material, and wipe gross residue from the tray while it is wet. 2. Transport in a closed container. 3. Remove set material from the perforations and the peripheral rim with a soft brush under running water; soften the film first if the tray material allows a brief soak, and never lever it out with a sharp instrument. 4. Process in the ultrasonic bath in a basket, at the dilution, time and temperature on the solution label — typically 2 to 10 minutes at 20 to 50 °C — with the tray positioned so its flanges are not loaded. 5. Rinse to the water quality the standard and the instruction sheet require, then dry completely, including the handle joint and the underside of the rim. 6. Inspect: even rims, no bent flange, no pitting, perforations clear. 7. Package in roll tubing or a pouch sized so the tray is not compressed, with the indicator visible. 8. Sterilize on a cycle the sterilizer's instructions validate for the load, allowing for the longer dry time a large metal mass needs. 9. Cool, verify the indicator, record the load. 10. Store closed, clean and dry.
How should a plastic or custom tray be processed?
The rule is the same, applied to a different limit. Read the material's maximum temperature and the sterilization methods it was validated for; if steam is not among them, do not invent a lower-temperature cycle and assume it is fine. Where the tray is a single-use item, the honest route is to dispose of it — a plastic stock tray reprocessed against its instructions is not a saving, it is an unvalidated device. Where the tray is reusable but heat-sensitive, cleaning followed by high-level disinfection with a product the sheet names, thorough rinsing, and complete drying is the defensible route, and the record of that step is the only evidence it happened.
Custom trays made in the practice deserve one extra sentence in the procedure. Their material documentation — not the tray convention — states the processing they tolerate, and a practice that prints trays has to keep that documentation with the resin, because the person mixing or printing is not the person who will be asked about it at an inspection.
What does the standard ask that tray habits skip?
CSA Z314:23, Canadian medical device reprocessing in all health care settings treats decontamination, packaging, sterilization and sterility maintenance as one chain. For trays, three points land hardest: the packaging has to be appropriate to the item — a bulky tray in an undersized pouch is a compromised sterile barrier, not a tight fit — the cleaning equipment has to be verified on each day of use, and each item has to be inspected before it is packaged. A practice that can show those three things for its trays is describing a process rather than a habit.
Provincial guidance sets the monitoring rhythm. In Ontario, the College's infection prevention and control standard requires a biological indicator on each day the sterilizer is used and for each type of cycle, a Type 4 or 5 chemical indicator in each package, and a Type 5 or 6 device where results are not quarantined before release. In Quebec, the joint ODQ and OHDQ guidelines set biological test frequency, indicator use, package information, register content and reprocessing-unit layout in chapter 6. A practice working in both provinces runs one process and documents it twice.
| Stage | What is required | What it means for a tray |
|---|---|---|
| Point-of-use treatment | Keep material from setting hard before cleaning | Set alginate in a perforation has to be softened and brushed, not levered |
| Cleaning | Manual cleaning of visible soil, then mechanical cleaning where used | Perforations, rims and the handle joint are the three surfaces that decide the result |
| Equipment verification | Cleaning equipment verified by a commercial method on each day of use | The bath's dated verification is part of the tray record, not a separate chore |
| Inspection | Each item inspected, function included | Rim flatness and flange alignment are pass or fail, not a judgement call |
| Packaging | Barrier appropriate to the item, indicator visible, Type 5 or 6 inside each package for steam | Roll tubing sized to the tray; a compressed pouch is a compromised barrier |
| Storage | Closed, clean and dry | A cabinet opened during an aerosol-generating procedure defeats the package |
Where does a clinic take this next?
Four things a clinic can act on rather than read: a printable compliance log sheet that records receiving dates, lot numbers and open-on dates and exports from the browser; the clinic supply planner that turns daily bench counts into cases per month; and, where a finding has to be documented for an inspector, Ask your compliance question, which returns a written answer citing the regulation or standard it rests on.
Facility and multi-site buyers can also ask about wholesale and multi-site ordering for case pricing and account setup. Reselling? become a distributor.
Where does a clinic take this next?
Four things a clinic can act on rather than read: a printable compliance log sheet that records receiving dates, lot numbers and open-on dates and exports from the browser; the clinic supply planner that turns daily bench counts into cases per month; and, where a finding has to be documented for an inspector, Ask your compliance question which returns a written answer citing the regulation or standard it rests on.
Facility and multi-site buyers can also ask about wholesale and multi-site ordering for case pricing and account setup.
Related reading
- Dental impression trays in Canada vs the US: which class applies
- How should Canadian audiologists disinfect otoscope specula and ear impression trays between patients
- What a dental infection control auditor checks about excavators, condensers and matrix bands
- Storage after sterilization: when a pack stays sterile and when it must be reprocessed
Frequently Asked Questions
Are impression trays semi-critical devices?
A tray that rests against the oral mucosa and is removed with set material on it belongs in the semi-critical group, where cleaning followed by high-level disinfection or sterilization is the expected minimum. Steam sterilization is preferred where the tray material tolerates it; high-level disinfection is the route for trays whose instructions exclude heat.
Can plastic impression trays be autoclaved?
Only if the tray's instruction sheet states a steam cycle it was validated for. Many plastic stock trays are single-use items, and a plastic tray processed above its material's stated maximum temperature can come out looking intact and be distorted enough to spoil an impression. The instruction sheet, not the practice's habit, decides.
How do you remove set alginate from the perforations?
Soften it and brush it out. Alginate sets through a reaction that does not reverse on its own, so the film has to be loosened — a brief soak where the tray material allows it — and then worked out with a soft brush under running water. Levering it out with a hand instrument is how perforations and rims get deformed.
Can a custom tray made in the practice be heat sterilized?
Only if the resin's documentation says the material tolerates that process. Custom trays are typically single-patient items, and the temperature limit belongs to the resin rather than to the tray category. Keep the resin documentation with the material so the claim can be supported later.
Does disinfection damage the tray surface enough to affect impressions?
It can. Repeated exposure to aggressive disinfectants leaves plastic trays crazed and rougher than they were, and chlorine-releasing products pit stainless steel, which is why the instruction sheet's permitted chemistry matters. A surface that has changed also changes how impression adhesive behaves, so the tray and the adhesive have to be treated as a pair.
How many impression trays does an operatory need?
Enough that a set is never the reason a tray is reused without processing. Count the peak number of impressions per hour, multiply by the hours from chairside to shelf — remembering that a large metal tray needs a longer dry time — and add one spare per size the practice stocks.
Sources
CliniEco Medical distributes clinic and laboratory consumables in Canada under MDEL #35334. Requirements that bind a specific practice remain the ones in its own provincial guidance, manufacturer instructions and written procedures.
Last updated: 16 November 2026.