In Quebec the restorative tray is processed under a document that spells out the reprocessing sequence in numbered sections, and the two sections most practices under-use are not the ones about cleaning. Section 6.3.4 covers lubrication, which sounds irrelevant to an excavator until a matrix retainer with a dry threaded knuckle comes back from the sterilizer stiff; section 6.9 covers the quality programme, which is where the written procedure, the training record and the annual review actually live. The cleaning sections still decide whether the tray is clean, but the paperwork sections decide whether the office can prove it.
The framework is the joint guidance of the Ordre des dentistes du Québec and the Ordre des hygiénistes dentaires du Québec, in force from publication in October 2024 and revised in February 2025, and it gives practices a two-year application period for the changes listed in chapter 6 — indicator use, biological test frequency, package information, register content and reprocessing-unit layout. A restorative tray touches four of those five, and the fifth, layout, decides where the ultrasonic bath is allowed to sit. The bath itself is an ultrasonic cleaner with a 7.5 L nominal tank in most practices of this size, dosed with a low-foam multi-enzyme ultrasonic solution.


Which chapter 6 sections decide the outcome for this tray?
The sequence runs from pre-cleaning at the chair through transport, receiving, manual cleaning, mechanical cleaning, lubrication, packaging, sterilization and storage, and each of those is a numbered section rather than a paragraph of advice. For a tray of excavators, condensers and bands the consequence of each section is concrete, which is what makes the guidance usable as a checklist.
| Section | What it addresses | What it decides for a restorative tray |
|---|---|---|
| 6.3.1 Pre-cleaning, brief inspection, transport | Treatment at the point of use and movement of the device | Composite and cement set; the gel or foam at the chair is the last chance to keep the bowl cleanable |
| 6.3.2 Receiving and manual cleaning | The soiled side of the unit | Bowl of the excavator, tip pattern of the condenser, knuckle of the retainer |
| 6.3.3 Mechanical cleaning | Ultrasonic or washer cycle | Basket, not loose; bands laid flat so edges cannot rub |
| 6.3.4 Lubrication | Whether and how a device is lubricated | Applies to the retainer's thread if the IFU says so, and to the forceps in the same load; not to a solid hand instrument |
| 6.3.5 Packaging | Preparation before sterilization | Band edges against film, indicator visible, package information added |
| 6.3.6 and 6.3.7 Sterilization and storage | Cycle and post-cycle storage | Wrapped cycle per the sterilizer IFU; closed, clean and dry storage afterwards |
| 6.4 and 6.5 Failure and recall | Failed cycles and device recalls | A failed restorative load has to be traced to the patients who received those instruments |
| 6.9 Quality programme | Procedures, qualifications, review | Written procedure for this tray, reviewed; staff with the training the section describes |
What does the lubrication section change in practice?
Lubrication exists in the guidance because some reusable devices have moving parts, and the matrix retainer is the item on this tray that qualifies: its knuckle is a threaded joint that has to move smoothly to hold a band under tension. Where the manufacturer's instruction sheet specifies a lubricant, the sequence is clean, dry, lubricate per the instruction, then package — and where the instruction sheet says nothing, the section 6.3.4 answer is that nothing is applied, because a lubricant that the device was not validated with can interfere with the surfaces the sterilant needs to reach.
The same section is where practices import a habit from the surgical tray and lubricate everything. A spoon excavator has no joint; a condenser has no joint; a metal band has no joint. Lubricating them adds an oil film that has to survive a steam cycle and then sits inside a pouch. The written procedure should therefore name the retainer, and only the retainer, unless an individual instruction sheet says otherwise.
How does the register handle a failed cycle?
Section 6.4 sets out what happens when sterilization fails and section 6.5 sets out the recall protocol, and both depend on a register that was filled in before the door closed. Annexe 4 of the guidelines gives an example register and states the information that has to appear; for a restorative tray the practical minimum is the set or tray identifier, the cycle, the date, the result of the indicator and the biological test where one applies, and the equipment used. A line reading "instruments, one load" cannot support a recall, which is the only moment the register is actually needed.
The same register logic applies to the bands. A band that has been reprocessed a dozen times is not a different infection control risk from a new one, but it is a different clinical device, and an office that writes a discard rule for creased or work-hardened bands and records when a band is retired has an answer when a restoration fails and the question of instrument condition comes up.
| Point of divergence | Quebec | United States (CDC guidance) |
|---|---|---|
| Biological indicator interval | Set in chapter 6 of the Quebec guidelines | At least weekly for each sterilizer |
| Heat-sensitive semi-critical item | Sterilized where the item can be sterilized | High-level disinfection acceptable at minimum |
| Package labelling | Chapter 6 adds information that has to appear on the package, in French for the office's own print | The facility follows the manufacturer's instructions and its own policy field by field |
| Who may run the biological test | The office may, with equipment and a register of results | Office or contracted service, per facility policy |
Where does the tray still catch people out?
The material-side traps are the same everywhere. Set composite keys into the serrations of a condenser and cannot be cavitated out; a creased band clings to set material at the crease; a retainer knuckle holds debris that no visual check reaches once the band is mounted. The control is mechanical: brush work at the bench, a bath that is verified on the day it is used, and an inspection that ends in a discard decision rather than a shrug. What Quebec adds is documentation — which set, which cycle, which result, in French, in a register that survives the day the sterilizer fails.
Where does a clinic take this next?
Four things a clinic can act on rather than read: a printable compliance log sheet that records receiving dates, lot numbers and open-on dates and exports from the browser; the clinic supply planner that turns daily bench counts into cases per month; and, where a finding has to be documented for an inspector, Ask your compliance question which returns a written answer citing the regulation or standard it rests on.
Facility and multi-site buyers can also ask about wholesale and multi-site ordering for case pricing and account setup. Reselling? become a distributor.
Related reading
- How to clean and sterilize excavators, condensers and matrix bands between patients
- How to clean and sterilize mouth mirrors and periodontal probes between patients in Quebec
- What a dental infection control auditor checks about excavators, condensers and matrix bands
- How many excavators, condensers and matrix bands a clinic needs per operatory
Frequently Asked Questions
Does a matrix retainer need to be lubricated in Quebec?
Only if the manufacturer's instruction sheet specifies a lubricant, in which case the device is cleaned, dried, lubricated as the instruction describes and then packaged. Section 6.3.4 of the provincial guidelines addresses lubrication as a reprocessing step rather than as routine maintenance, so a device whose instruction sheet does not call for it should not be lubricated, and a solid hand instrument such as an excavator never is.
Can a matrix band be sterilized unpackaged in an emergency?
The guidelines address unpackaged sterilization in section 6.6, which requires a written protocol before the practice uses it rather than a decision taken at the chair. An unpackaged item also has to be used immediately, because it has no packaging to maintain sterility, so it is not a way to keep a spare band on the shelf.
What qualifications does the person reprocessing instruments need in Quebec?
Staff assigned to reprocessing and to the infection prevention protocol are expected to hold basic training, such as a vocational diploma in dental assistance or an attestation in medical device reprocessing. Where a staff member does not hold that training, the office is expected to provide bridging training so the person can understand and apply the protocols in the guidelines, and the quality programme section asks the office to keep the training record.
What has to be in the register when a sterilization cycle fails?
Enough to identify which devices were in the load and which patients received them. The guidelines set out a failure protocol in section 6.4 and a recall protocol in section 6.5, and both operate on the register whose example appears in Annexe 4 — set or tray identifier, cycle, date, indicator result, biological result where applicable and the equipment used. A generic description of the load cannot support a recall.
Do amalgam-contaminated instruments need special handling before cleaning?
Infection control and waste rules are separate obligations here: cleaning and sterilization follow the reprocessing sequence, while amalgam scrap and contaminated waste follow the provincial waste rules, which treat dental amalgam as a material with its own collection route. Gross debris is removed chairside into the appropriate container so that it does not travel to the reprocessing bench at all.
Sources
CliniEco Medical distributes clinic and laboratory consumables in Canada under MDEL #35334. Requirements that bind a specific practice remain the ones in its own provincial guidance, manufacturer instructions and written procedures.
Last updated: 16 November 2026.