A fertility clinic reprocesses less than a dental office and more than its staff often assume. The metal specula, the ring forceps, the instrument trays and the stainless steel basins go round again; the embryo transfer catheter, the ICSI pipette and the collection tube do not. Between those two groups sits a category that causes most of the trouble: items the clinic has always reused but has never validated, because nobody wrote down how.
This page sets out which items in a Canadian fertility clinic are reusable, what the national reprocessing standard asks of the clinic that reuses them, how a speculum should travel from the procedure room back to the shelf, and where the Canadian and American positions part. The consumables that carry the reusable loop are the Class 4 self-sealing sterilization pouch, the Class 5 steam chemical integrator, and the multi-enzyme ultrasonic cleaning solution in the bath.
Quick facts on reprocessing in a fertility clinic
- CSA Z314:23 covers reprocessing of medical devices in all health care settings, so it applies to a fertility clinic without a hospital licence.
- A device that arrives labelled single use comes with no manufacturer's validated reprocessing instructions, which is the input the standard assumes.
- Ontario fertility clinics operate as independent health facilities under the Independent Health Facilities Act; Quebec requires a licence for assisted procreation activities under chapter A-5.01.
- A metal vaginal speculum is product code HDF at 21 CFR 884.4520, class 1 and exempt; a nonmetal vaginal speculum is HIB at 21 CFR 884.4530, class 2 and exempt.
- Assisted reproduction pipettes sit at 21 CFR 884.6130, class 2, with both cleared and exempt product codes in the classification database.
- Heat-sensitive items that cannot take steam are processed under the ethylene oxide standard, ISO 11135.
Which items in a fertility clinic are actually reusable?
The dividing line is not material, it is the label and the manufacturer's instructions. An item is reusable when the manufacturer supplies validated reprocessing instructions; everything else is single use regardless of what it is made of. The table below sorts the common items by where they sit.
| Item | Typical use | Reprocessing position |
|---|---|---|
| Metal vaginal speculum | Examination, embryo transfer | Reusable, steam sterilizable |
| Ring forceps and sponge forceps | Preparation, tray handling | Reusable, steam sterilizable |
| Stainless basins and trays | Holding cleaned items | Reusable, with a validated load pattern |
| Surgical instruments for retrieval | Egg retrieval procedures | Reusable where the manufacturer says so |
| Transvaginal ultrasound probe | Monitoring, retrieval | Semi-critical; sheath plus disinfection per instructions |
| Embryo transfer catheter | Transfer | Single use, no reprocessing |
| ICSI and handling pipettes | Micromanipulation | Single use, no reprocessing |
| Culture dishes and tubes | Laboratory | Single use, no reprocessing |
Two of these need a note. The ultrasound probe contacts mucous membrane, so it is a semi-critical device and the provincial guidance on cleaning, disinfection and sterilization of medical devices applies to it in full; a sheath is a barrier, not a substitute for the disinfection step in the manufacturer's instructions. The laboratory side is the opposite problem: the items most likely to be improvised are the ones with the least tolerance for it, because a pipette that has been cleaned rather than replaced changes the volume it delivers.
What does the Canadian reprocessing standard require?
CSA Z314:23 is the national standard for reprocessing medical devices in all health care settings, and it replaced the earlier parts of the Z314 series that dealt separately with steam sterilization and with effective sterilization practice. For a fertility clinic the consequence is organisational rather than technical: the clinic has to be able to show a reprocessing programme — written procedures, trained staff, validated cycles, records — rather than a set of habits around a benchtop unit.
The technical inputs come from three further standards. ISO 17664-1:2021 defines the information a manufacturer must supply so that a device can be reprocessed, which is what the clinic follows for each reusable item. ISO 17665-1:2006 covers moist heat sterilization and is the basis for the steam cycle a speculum goes through. For items that cannot take steam, ISO 11135-1:2007 covers ethylene oxide, and it is a different programme with different validation, monitoring and aeration requirements rather than a fallback cycle.
The monitoring layer is where a small clinic most often has a gap. ISO 11140-1:2014 sets the requirements for chemical indicators by type, and ISO 11138-1:2017 does the same for biological indicators. A pouch with an external indicator and an internal indicator covers routine package-level monitoring; a process challenge device carrying a Type 5 or Type 6 indicator is what supports release of a load, and a biological indicator is what confirms the cycle actually killed spores.
How should a speculum travel from the procedure room back to the shelf?
Six steps, and each one leaves a trace. The sequence below is the one the provincial guidance supports, written for a clinic without a dedicated reprocessing room.
| Step | What is done | What is recorded |
|---|---|---|
| Point of use | Gross soil removed, item placed in a covered puncture-resistant container | Nothing yet; the container protects the person carrying it |
| Cleaning | Enzymatic or detergent cleaning, ultrasonic bath where the item allows | Daily solution change; equipment test result |
| Rinsing and drying | Rinse to remove residue, dry before packaging | Inspection outcome |
| Inspection and packaging | Hinges and jaws checked, item dried, sealed in a pouch with an internal indicator | Date, sterilizer, cycle or load number, initials |
| Sterilization | Cycle per the sterilizer manufacturer's instructions, load not overloaded | Physical parameters; indicator result |
| Storage and release | Sealed packages in a closed cabinet, not under a sink | Release decision and the basis for it |
The two steps that get shortened in a busy clinic are cleaning and drying. A speculum with dried organic material in the hinge will survive a cycle that kills everything on the outside of the package and still present a cleaning failure at inspection, and a wet package is a failed package regardless of the indicator. Both problems show up in the same place: the inspection sheet.
The validation question is separate from the daily loop. A clinic that has changed sterilizer, changed packaging, or added an instrument it has never processed needs to show that the new combination has been tested, and the standard for the risk side of that judgement is ISO 14971:2019. In practice this is a short written record: what changed, what was tested, and what the result was.
How do Canada and the United States differ on a device labelled single use?
It stays single use, and the reason is documentary rather than moral. A device labelled for single use is not supplied with validated reprocessing instructions, so the clinic has nothing to follow and nothing to validate against. The manufacturer's information requirement in ISO 17664-1:2021 is what a reusable device carries and a single-use device does not.
In Canada, the Medical Devices Regulations framework described by Health Canada governs authorisation for sale and import, and the in-house reuse question is answered by the facility's own validation and by provincial requirements. In the United States the position is more explicit: the FDA page on reprocessing single-use medical devices sets out the agency's oversight of facilities that reprocess these devices, which is why a US clinic buying reprocessed single-use devices asks for the reprocessor's authorisation rather than treating the item as ordinary stock.
For a fertility clinic the practical line is simple and worth writing into the policy: embryo transfer catheters, ICSI pipettes, handling pipettes, culture vessels and needles are opened, used once and discarded, whatever the cost per unit. A clinic that has been cleaning and re-sterilizing a catheter to cover a supply gap is not making a reprocessing decision; it is making an unvalidated one.
How do Canada and the United States differ on fertility clinic reprocessing?
Three differences matter: how the clinic is authorised, which standard governs the reprocessing programme, and how a device's regulatory class is set. The third one surprises people, because the material changes the answer.
| Item | Canada | United States |
|---|---|---|
| Clinic authorisation | Provincial: independent health facility licence in Ontario, assisted procreation licence in Quebec | State licensure, plus federal device rules for what the clinic uses |
| Reprocessing standard | CSA Z314:23, with provincial guidance | AAMI and CDC guidance, with manufacturer instructions |
| Metal vaginal speculum | Class by Canadian rule; reusable where the manufacturer says so | Product code HDF, 21 CFR 884.4520, class 1 and exempt |
| Nonmetal vaginal speculum | Same question, answered by the label | Product code HIB, 21 CFR 884.4530, class 2 and exempt |
| Single-use reprocessing | In-house question settled by facility validation and provincial rule | Reprocessor oversight described by the FDA |
| Record basis | Programme records required by the provincial standard and the facility licence | Facility policy, accreditation and state survey |
The classification point is worth keeping: in the United States, a stainless steel vaginal speculum is class 1 and a disposable plastic one is class 2, both exempt from premarket notification under the product codes above, which is why the two are not interchangeable in a purchasing record even when they do the same job in the room. The openFDA device classification database is the fastest check, and it returns the regulation number and the submission type for the code.
Which records close the loop?
Four, and they are the same four a dental or medical clinic keeps. The load record ties a date, a sterilizer, a cycle and an operator to a set of instruments. The indicator record ties the load to a pass or a fail. The maintenance record ties the sterilizer to the service history the manufacturer's instructions assume. The training record ties the operator to the procedure they are following.
Retention is set by the provincial regime and by the facility licence, and the longest period in common use in Ontario is ten years from the date of the last entry, the figure the dental standard applies to a sterilizer log. A fertility clinic that adopts it will not be asked for more by any reviewer, and the alternative — a log discarded every two years — cannot answer a question about a patient cycle eighteen months ago.
Ontario fertility clinics operate under the Independent Health Facilities Act, and Quebec clinics under the Act respecting clinical and research activities relating to assisted procreation, which is where the licence conditions that reach the reprocessing programme come from. The professional guidance that fills in the clinical expectations is published by the Canadian Fertility and Andrology Society, and the device-level reprocessing instructions come from each manufacturer under ISO 17664-1.
What changes in the laboratory rather than the procedure room?
The laboratory reprocesses equipment rather than instruments, which is a different programme. Incubators, heated stages, micromanipulators and cryostorage vessels are cleaned and maintained under manufacturer instructions, and the record is a maintenance and monitoring log rather than a load record. Where the laboratory uses an ultrasonic bath for handling tools, the daily solution change and the equipment test are the same entries as in the procedure room.
The line to hold is that laboratory consumables in contact with gametes or embryos are single use and are not cleaned and reused, whatever the cost pressure. The classification of assisted reproduction pipettes at 21 CFR 884.6130 — class 2, with both cleared and exempt product codes — is a reminder that these are regulated devices, not generic glassware.
Where are the forms for the programme?
The load record, the inspection sheet and the wall log are collected in the compliance log centre, which also carries the sterilization log generator for a clinic setting up a second sterilizer.
Writing the reprocessing programme for a clinic that has never had one written down? Ask a Compliance Specialist with the instrument list, the sterilizer models and the provincial licence you operate under, and the answer will name the items that need validated instructions before the next inspection.
Ordering for several clinics in a network? The institutional account enquiry page covers case quantities and account setup. Reselling? become a distributor.
Related reading
- Disposable consumables for IVF clinics
- Medical device reprocessing and sterilization in Canadian facilities
- ISO 17664 reprocessing instructions for clinics
- Instrument reprocessing workflow explained
- Minor procedure reprocessing by specialty
Sources and version notes
- CSA Z314:23, reprocessing of medical devices in all health care settings — checked 17 November 2026.
- ISO 17664-1:2021, information to be provided by the manufacturer for the processing of medical devices — checked 17 November 2026.
- ISO 17665-1:2006, moist heat sterilization of health care products — checked 17 November 2026.
- ISO 11135-1:2007, ethylene oxide sterilization — checked 17 November 2026.
- ISO 11140-1:2014, chemical indicators, general requirements — checked 17 November 2026.
- ISO 11138-1:2017, biological indicators for sterilization processes — checked 17 November 2026.
- ISO 14971:2019, application of risk management to medical devices — checked 17 November 2026.
- Health Canada, medical devices in Canada — checked 17 November 2026.
- US Food and Drug Administration, reprocessing single-use medical devices — checked 17 November 2026.
- openFDA device classification database — checked 17 November 2026.
- Independent Health Facilities Act, R.S.O. 1990, c. I.3 — checked 17 November 2026.
- Act respecting clinical and research activities relating to assisted procreation, CQLR c. A-5.01 — checked 17 November 2026.
- Canadian Fertility and Andrology Society, clinical practice guidelines — checked 17 November 2026.
- Public Health Ontario, reprocessing — checked 17 November 2026.
- Public Health Ontario, environmental cleaning for prevention and control of infections — checked 17 November 2026.
- Public Health Ontario, routine practices and additional precautions in health care settings — checked 17 November 2026.
- British Columbia Ministry of Health, cleaning, disinfection and sterilization of medical devices — checked 17 November 2026.
- CDC, disinfection and sterilization guideline, executive summary — checked 17 November 2026.
- Occupational Safety and Health Administration, bloodborne pathogens — checked 17 November 2026.
- 29 CFR 1910.1030, bloodborne pathogens — checked 17 November 2026.
- World Health Organization, medical devices — checked 17 November 2026.
Frequently Asked Questions
Can a fertility clinic reprocess a speculum in house?
Yes, where the manufacturer supplies validated reprocessing instructions. That is what makes the item reusable. The clinic follows those instructions under CSA Z314:23, with steam sterilization for items that tolerate it.
Is a transvaginal ultrasound probe reusable?
Yes, but it is handled as a semi-critical device: a sheath for the examination and disinfection per the manufacturer's instructions between patients. The sheath is a barrier and does not replace the disinfection step.
Can an embryo transfer catheter be cleaned and sterilized again?
No. It is supplied for single use with no validated reprocessing instructions, so there is nothing to follow and nothing to validate. The same applies to ICSI pipettes and handling pipettes.
Which standard governs the reprocessing programme in Canada?
CSA Z314:23, which covers all health care settings, with ISO 17664-1:2021 supplying the manufacturer's instructions for each device and ISO 17665-1:2006 covering the moist heat cycle.
Does a US speculum carry the same class as a Canadian one?
The classes are set by different systems. In the United States a metal vaginal speculum is product code HDF at 21 CFR 884.4520, class 1 and exempt, while a nonmetal one is HIB at 21 CFR 884.4530, class 2 and exempt, which the openFDA classification database returns directly.
How long should the sterilizer log be kept?
Retention is set by the provincial regime and the facility licence. Ten years from the date of the last entry is the longest period in common use in Ontario, and adopting it satisfies every reviewer a clinic is likely to meet.
What has to be recorded when a new instrument is added?
That the combination of instrument, packaging and cycle has been validated: what changed, what was tested, and the result. ISO 14971:2019 supplies the risk framework for deciding how much testing is proportionate.
Standards, regulations and manufacturer instructions are cited as published at the time of writing and are not reproduced in full. Device classification and provincial requirements differ by jurisdiction and are revised, so confirm the version in force for your setting. This article is for information and is not legal advice. CliniEco Medical distributes medical consumables under MDEL #35334.