At 07:40, a respiratory therapist wheels the intubation tray toward a patient with suspected COVID-19. Within minutes, suctioning and airway manipulation will generate a plume of aerosols that can linger in the room long after the procedure ends. Her respirator protects her airway, but her eyes, conjunctiva, and face remain exposed to droplet splatter travelling several feet. A face shield closes that gap — and for aerosol-generating procedures, it is not an accessory; it is a required layer of defence.

Quick facts
- A face shield is a separate PPE layer, not a mask substitute: it protects the eyes, conjunctiva and the front of the face from droplet and splash, while the mask handles inhalation.
- In Canada the reference document for eye and face protectors is CSA Z94.3; the US equivalent is ANSI/ISEA Z87.1. Ask for the certification on the datasheet, not the marketing page.
- Coverage target: below the chin, out to the temples, sitting over the top edge of the mask without disturbing its seal.
- Anti-fog performance decides compliance — a shield that fogs gets pushed up, and every adjustment is an open barrier.
- Disposable versus reusable is a reprocessing-capacity decision, not a price decision.
CliniEco Medical (MDEL #35334) supplies these lines in Canada and ships from Toronto.
Why Face Shields Belong in the PPE Matrix
Face shields are a distinct PPE category, not a substitute for masks. They provide full-face coverage against droplets, splashes, and self-inoculation — the route where a worker touches a contaminated surface and then touches their face. For facilities that have standardized on procedural masks and isolation gowns, adding face shields completes the barrier without changing workflows.
Health Canada lists eye and face protection among the core elements of droplet and contact precautions. When paired with a CliniEco 3-ply ASTM Level 1 procedural mask and a CliniEco Level 1 isolation gown, a shield addresses the three exposure routes that matter most: inhalation, mucous membrane contact, and contamination of clothing.
Optical Standards: CSA Z94.3 and ANSI/ISEA Z87.1
In Canada, the reference document for eye and face protectors is CSA Z94.3. In the United States, the equivalent is ANSI/ISEA Z87.1. Both standards evaluate impact resistance, optical clarity, and coverage. A shield that meets one of these marks has been tested, not just designed, for workplace use.
What to look for on the label or datasheet:
- CSA Z94.3 certification for Canadian distribution
- ANSI/ISEA Z87.1 marking for impact-rated lenses
- Optical quality rating — shields with poor optics cause eye strain during long shifts
- Manufacturer documentation confirming compliance, which your safety officer will want on file
Anti-Fog Design: The Difference Between Coverage and Compliance
A shield that fogs within minutes of donning will be pushed up, adjusted, or removed — and every adjustment is a moment when the barrier is open. Anti-fog coatings keep the lens clear by preventing condensation from forming on the inner surface. The coating quality matters: low-grade coatings wear off after a few cleaning cycles, while durable anti-fog treatments survive repeated disinfection with the wipes your facility already uses.
For high-exertion tasks or long procedures, consider shields with ventilation channels or moisture-absorbing brow pads, which reduce fogging even when ambient humidity is high.
Disposable vs. Reusable Face Shields
The choice between single-use and reusable shields comes down to workflow. Disposable shields are suited to high-turnover units where reprocessing capacity is limited. Reusable models with replaceable lenses suit departments with established reprocessing protocols.
- Disposable: no decontamination steps, lower per-unit cost at volume, predictable stock rotation
- Reusable: lower waste over time, higher upfront cost, requires validated cleaning between uses
- Hybrid frames: reusable frame with a replaceable visor, a practical middle ground for clinics

Building the Full Barrier: Shields with Masks and Gowns
A face shield is most effective as part of a system. For aerosol-generating procedures, the sequence is: perform hand hygiene, don the gown, apply the mask, and put on the shield last so it sits over the mask's upper edge without disturbing the seal. Suppliers such as 3M and Kimberly-Clark publish fit and seal guidance for their respirators; the same discipline should apply to how shields sit over masks in your facility.
Stocking masks and shields from the same source simplifies procurement. A CliniEco individually wrapped surgical mask in every procedure cart, alongside a shield, means staff never improvise a barrier mid-shift.
Selection Tips for Procurement Teams
When evaluating face shields for your facility, work through a short checklist:
- Verify optical certification (CSA Z94.3 or ANSI/ISEA Z87.1) in the supplier's documentation
- Confirm the anti-fog coating is rated for repeated cleaning
- Check coverage — the shield should extend below the chin and to the temples
- Test compatibility with the masks and respirators already in use
- Request samples before committing to a volume order
Face shields are the natural next step after masks and gowns in your PPE program. They are a modest investment, a tested barrier, and a visible signal to staff that their safety is taken seriously. Start with a small pilot on one unit, measure compliance and comfort, then expand.
Browse our face masks.
Related reading: explore our infection control resources for clinics.decode HAI, SSI, CJD and MDRO acronyms in our infection control pillar article.
Disposable and reusable face shields are two different cost models, and a facility usually runs both. The clinic supply and cost planner models monthly volumes for each so the choice can be made on numbers, returning a monthly quantity, the whole packs or cases to order, and a monthly cost in CAD. Where a shield is cleaned and turned around between patients, the printable sterilization and reprocessing log keeps that cycle record alongside the instrument log. A clinic that reprocesses both can ask a compliance specialist which reprocessing cycles a face shield actually needs documented.
Face Shield Specifications at a Glance
Procurement usually ends up running both formats: disposables where turnover is high, reusable frames where reprocessing is already validated. This is what separates them on paper.
| Attribute | Disposable shield | Reusable frame + replaceable visor |
|---|---|---|
| Certification to verify | CSA Z94.3 (Canada) or ANSI/ISEA Z87.1 (US-sourced stock) | Same marks, plus a visor replacement part number |
| Visor material | Optical-grade PET film, single thickness | Polycarbonate or PET visor, thicker and re-cleanable |
| Anti-fog | Factory coating, one service life | Coating survives validated disinfection; visor replaced when it fails |
| Cleaning between uses | None — discard after the encounter | Validated disinfection per the facility's reprocessing protocol |
| Coverage | Chin-to-temple, full face width | Same, but dependent on frame fit and adjustment |
| Documentation burden | Lot and date on the case | Reprocessing cycle record kept with the instrument log |
| Typical fit | Isolation rooms, AGMP carts, high-turnover clinics | Departments with an existing reprocessing workflow |
Neither column holds a lower cost in every setting. The number to compare is cost per use after reprocessing labour and validated-cycle documentation are counted, not the unit price on the invoice.
How Do You Choose Between Disposable and Reusable Shields?
Start with what the department already does well. If the facility runs a validated reprocessing loop for instruments — trained staff, logged cycles, audited dry time — a reusable frame with replaceable visors slides into an existing workflow. If there is no reprocessing capacity on the unit, a reusable shield becomes either a single-use item at a higher price or a cleaning shortcut waiting to be audited.
Then look at turnover. In a unit where a dozen aerosol-generating procedures run in a shift, disposables avoid a bottleneck at the sink. In a small clinic that fits two shields a week, the reprocessing question is small enough that either choice is defensible — what matters is that the choice is written down, with the cleaning product and contact time named.
When Should a Face Shield Be Replaced?
A disposable shield is finished at the end of the encounter that soiled it, or at the end of the shift, whichever comes first. Replace immediately if it is splashed with blood or body fluid, if the visor is scratched enough to distort the view, or if the headband has stretched so the shield no longer sits over the mask's upper edge.
For reusable frames, replace the visor when the anti-fog coating fails after cleaning, when clarity is compromised, or when the frame no longer holds adjustment. Record the replacement in the same log that carries the reprocessing cycle, so the shield's history is auditable alongside the instruments it protects the operator from.
Related reading
Frequently Asked Questions
Do face shields replace masks?
No. A shield blocks droplets and splashes from reaching the eyes, conjunctiva and the front of the face; it does not filter what is inhaled. For aerosol-generating procedures the two are worn together — mask or respirator first, shield last so it sits over the mask without breaking the seal.
What standard should a Canadian clinic verify on a face shield?
CSA Z94.3 is the Canadian reference for eye and face protectors. US-sourced stock marked ANSI/ISEA Z87.1 is acceptable where the supplier provides documentation, which the facility safety officer keeps on file. A shield with neither mark has been designed for the purpose, not tested for it.
How long can a disposable face shield be worn?
For one encounter or one shift, whichever ends first. Replace it as soon as it is soiled, splashed, scratched or fogging persistently. Shields are not cleaned and re-worn in a clinical setting unless the model is explicitly a reusable one.
Can face shields be disinfected and reused?
Only reusable models, and only with the disinfectant and contact time the manufacturer has validated. Disposable PET visors degrade with repeated disinfection and lose their anti-fog coating, which is the point at which staff start pushing them up instead of wearing them.
Does a face shield need to cover the chin?
Yes. Coverage should extend below the chin and out to the temples. A shield that stops at the jaw leaves the underside of the face and the sides of the eyes exposed to splatter arriving from below or from the side, which is exactly the path suction and irrigation create.