Quick facts
- A cytocentrifuge spins a fluid sample so that its cells settle onto a small area of a slide, which is how a laboratory turns a dilute specimen into a readable, concentrated smear.
- United States: it is a named device at 21 CFR 864.3300, titled "Cytocentrifuge", placed in Class I, and the openFDA classification API lists it under product code IFB.
- Canada: no entry names a cytocentrifuge. A non-invasive laboratory instrument is classified by rule, and Rule 7(1) of Schedule 1 to the Medical Devices Regulations, SOR/98-282 puts all other non-invasive devices in Class I.
- Rule 7(2) lifts that device to Class II when it is meant to act as a calibrator, tester or quality-control support to another device, or to be connected to an active device already in Class II, III or IV.
- The two countries land on the same class for the instrument and reach it in two different ways: the United States by a named entry, Canada by the non-invasive rule.
- The entry and rule text below were checked against the current CFR and the Regulations on 2026-10-09.
A cytocentrifuge sits between the specimen and the slide, and it is a clean example of how each country files a laboratory instrument that prepares a sample rather than contacting a patient. This article sets out what the instrument is, how each country reaches its class, and what a laboratory or a buyer should be able to point at when a cytocentrifuge and its consumables are ordered.
What is a cytocentrifuge?
The instrument holds a small funnel and a slide in a rotor, spins the sample at controlled speed for a set time, and leaves the cells spread evenly inside a small circle on the slide. It is used for body fluids — cerebrospinal fluid, urine, sputum and fine-needle aspirates — where the cell count is low and a plain smear would be too thin to read.
The fact that decides the classification is that the instrument processes a specimen rather than contacting a patient. It is a non-invasive laboratory device, it carries no imaging function and no patient contact, and that combination is what both countries act on when they file it.
How does the United States file a cytocentrifuge?
In the United States the instrument is a named device. 21 CFR 864.3300 is titled "Cytocentrifuge" and places it in Class I. The openFDA classification database lists the entry under product code IFB.
A Class I device of this kind reaches the market under general controls rather than under premarket approval. The named entry covers the instrument, and it does not change when the rotor is built for a different funnel size or when the instrument is combined with a staining unit into one benchtop module — the entry still reads as a cytocentrifuge.
How does Canada classify a cytocentrifuge?
Canada does not keep a named entry for a cytocentrifuge in its classification rules. Instead, Schedule 1 to the Medical Devices Regulations, SOR/98-282, classifies a device by how it meets the body, and a cytocentrifuge is a non-invasive instrument that the rules do not otherwise name. Rule 7(1) reads: "Subject to subrule (2), all other non-invasive devices are classified as Class I."
The hooks that can move the class are in Rule 7(2): a non-invasive device is classified as Class II if it is intended "(a) to act as a calibrator, tester or quality control support to another medical device; or (b) to be connected to an active device that is classified as Class II, III or IV." A standalone cytocentrifuge does neither, so it stays in Class I and reaches the market through a device licence under section 32 of the Regulations. The distinction bites when the centrifuge is sold as a module inside a larger automated staining system: if the system is an active device in Class II or above and the cytocentrifuge is meant to be connected to it, the hook in 7(2)(b) can lift the class.
| Item | Canada | United States |
|---|---|---|
| Named entry | None; classified by rule | 21 CFR 864.3300 |
| Class | Class I by Rule 7(1) | Class I |
| Basis of the class | The rule that fits a non-invasive instrument | The named entry the instrument is filed under |
| Product code | Not applicable | IFB |
| Class-lifting hook | Rule 7(2): calibrator/tester, or connected to a Class II–IV active device | Special controls if the FDA names one |
| Premarket route | Device licence under section 32 for a Class I device | General controls |
| Quality system | CAN/CSA-ISO 13485 certificate behind the licence | Quality system regulation |
The two countries agree on the class for the same physical reason and reach it in two different ways. A laboratory that orders a cytocentrifuge against a Canadian purchase order should expect the file behind it to carry a licence number and a quality-management certificate, because those are the records the Regulations attach to a licensed device whatever the instrument is called.
Which standards sit behind the instrument?
The class says how the instrument is regulated; the standards say how it has to behave. IEC 61010-2-020:2016 is the safety standard for laboratory centrifuges and covers the rotor, the interlock and the containment of a burst. ISO 15189:2022 is the competence-and-quality standard that a medical laboratory is assessed against, and ISO 13485:2016 is the quality-management basis behind the licence.
| Element | What it covers | Why it matters at the bench |
|---|---|---|
| Rotor speed | The controlled spin for the set time | An over-spun sample shreds the cells |
| Lid interlock | The cut-off if the lid opens | The spinning rotor is the injury risk on the bench |
| Containment | The sealed rotor or cup | An aerosol from an infectious sample is the exposure risk |
| Funnel and slide fit | The cell-spot area | A poor fit spreads the cells beyond the reading area |
| Markings | Model and serial legibility | Faded markings force a re-identification |
| Traceability | Maker, model and serial number | An instrument cannot be reconciled to a licence without them |
An instrument that arrives without a maker, a model designation and a serial number cannot be reconciled with a licence, and it should not be accepted into a laboratory.
What should a buyer check with an order?
A cytocentrifuge bought on a Canadian purchase order and the same instrument bought in the United States are the same physical article with two rule paths behind them. The ways to reconcile them are the same on both sides of the border: a maker, a model designation, a serial number and the instructions for use, together with the rotor-speed and containment specification the instrument is checked against. A buyer who asks for those fields is asking for the traceability the device rules require, whatever the instrument is called.
The one place the two markets part is the wording. A Canadian laboratory should expect the file to identify the article by the rule that classified it, while a buyer in the United States should expect it to read as a cytocentrifuge against product code IFB. Neither file is wrong; each is answering the question its own market asked.
What else sits beside the cytocentrifuge?
A specimen-preparation bench is stocked as a system rather than as a single instrument. Sterile 15 mL centrifuge tubes in a 500-case sit with the bench for the spins that feed the instrument, and graduated leak-proof 90 mL specimen cups are kept for the samples that arrive before preparation. Laboratories that also reprocess instruments pair the bench with the sterilization monitoring collection for their own load records. Multi-site groups ordering at case level use the wholesale ordering page, and the B2B wholesale collection lists the lines held for institutional buyers. Reselling? become a distributor.
Sources
- 21 CFR 864.3300, Cytocentrifuge
- IEC 61010-2-020:2016, laboratory centrifuges
- ISO 15189:2022, medical laboratories
- ISO 13485:2016, quality management
- ISO 14971:2019, risk management
- Health Canada, medical devices
- Public Health Ontario laboratory services
- CCOHS, needlestick and sharps injuries
- CCOHS, OSH answers
- WHO laboratory biosafety manual
- Electronic Code of Federal Regulations, Title 21
- US FDA, device classification database (cfPCD)
- US FDA, 510(k) premarket notification database (cfPMN)
- US FDA, device registration and listing (cfRL)
- openFDA device classification API
A specimen bench is audited on paper as often as it is audited on the shelf. The printable equipment and maintenance log centre carries a blank sheet with columns for the instrument, its serial number, the check performed and the date, so a laboratory can reconcile the centrifuge it uses with the record it keeps.
The log sheet generator on the same page sizes the sheet to the number of preparation benches a laboratory runs, so a single-instrument room and a multi-bench laboratory print the same form at two different volumes.
Every laboratory and every instrument differs. Ask a compliance specialist and you will get a written answer specific to your equipment and province, with the regulation or standard it is based on cited.
Related reading
- Laboratory centrifuges in Canada vs the US: which class applies
- Centrifuge tubes 15 mL vs 50 mL: stocking a clinic laboratory
- Microcentrifuge tubes in Canada vs the US: which standards
CliniEco Medical supplies eye care, laboratory and dental consumables of the kind described in this article. MDEL #35334. This article is written for optometry, laboratory and procurement professionals and is not legal advice; the class of a device and the records kept by a practice belong to the manufacturer and to the requirements that apply to it.
Frequently Asked Questions
Is a cytocentrifuge a medical device?
Yes, in both countries. It prepares a concentrated cell smear that a laboratory reads in diagnosis, so it is a device; in Canada it is a non-invasive device classified under Rule 7(1), and in the United States it is a named device at 21 CFR 864.3300.
What class is a cytocentrifuge in the United States?
It is Class I at 21 CFR 864.3300 under product code IFB. It reaches the market under general controls rather than under premarket approval.
Does Canada class a cytocentrifuge as Class I or Class II?
A standalone cytocentrifuge is Class I under Rule 7(1). It becomes Class II only if it is meant to act as a calibrator, tester or quality-control support to another device, or to be connected to an active device already in Class II, III or IV.
Is a cytocentrifuge the same as a laboratory centrifuge?
No. A general laboratory centrifuge separates a sample into fractions in a tube, while a cytocentrifuge spins a fluid suspension so that the cells deposit onto a slide in a small, readable spot. They are different entries and one is built around the slide, not the tube.
Why does an aerosol matter in a cytocentrifuge?
Because the sample can carry an infectious agent, and a spinning rotor can release an aerosol if the cup is not sealed or the lid is opened early. The containment parts of the instrument are what control that risk, which is why the safety standard for laboratory centrifuges covers them.
What should a laboratory keep with a cytocentrifuge?
A maker, a model designation and a serial number, plus the licence number and the rotor-speed and containment specification the instrument is checked against. Those are the fields that let an instrument be reconciled with a licence and recalled if a batch is affected.
Does a cytocentrifuge need a quality-management certificate?
The certificate sits with the manufacturer rather than with the laboratory. Asking for the CAN/CSA-ISO 13485 certificate and the risk file is the way a buyer sees that the design and the records behind the instrument are in place.