Contract Sterilization and Third-Party Reprocessing: What a Facility Must Verify in a Supplier Audit

Class 4 self-sealing sterilization pouch, 2.5 x 4 inch, with external and internal process indicators and a write-on panel

Quick facts

  • Contract sterilization moves the process, not the responsibility. A facility that sends instruments out still has to be able to name who sterilized which load, on which date, with which validated cycle.
  • The licence that matters depends on the role, not the company name: in Canada a manufacturer of a Class II, III or IV device holds a medical device licence, while a person who imports or sells a device holds an establishment licence under section 44 of the Medical Devices Regulations.
  • Process validation is cycle-specific and product-specific. A supplier that can produce an ISO 11135 report for one device family cannot use it to answer a question about a different packaging configuration or load density.
  • Traceability is the item that fails audits most often: the chain from your lot number to the sterilization load, and back, is what a recall depends on.
  • Six of the twenty items on the list below are stop-sign items. If a supplier cannot produce them, the audit ends there rather than continuing to the commercial discussion.

Outsourcing sterilization is a normal arrangement for clinics without a chamber large enough for implant sets, for laboratories with heat-sensitive devices, and for manufacturers without in-house ethylene oxide capacity. It is also the arrangement in which a facility loses direct sight of the process, which is why the audit has to substitute documents for observation.

This article is written for the buyer who has to sign the quality agreement: a clinic manager evaluating a mail-in service, or a device company evaluating a contract sterilizer. It sets out what Canadian licensing actually requires, then gives a twenty-item checklist organised by the six domains that an assessor will walk, and closes with the red lines — the items whose absence means the conversation ends.

One item on the list is decided before the goods ever leave your bench. Packaging that is part of the validated configuration has to travel with the load: a Class 4 self-sealing pouch records exposure at the pack level, and the load record and release signature carry everything the pouch cannot.

What does Canadian licensing actually require of a contract sterilizer?

The Medical Devices Regulations separate two licences, and buyers routinely conflate them. Section 44 of the regulations prohibits any person from importing or selling a medical device unless that person holds an establishment licence, with defined exemptions that include retailers, health care facilities, and manufacturers of Class II to IV devices. The manufacturer's own authorisation — the medical device licence — is a different instrument, and it is held by the manufacturer of a Class II, III or IV device, not by the company that runs the chamber.

For a facility sending instruments out, the practical consequence is a two-question test. Ask which legal role the supplier is performing for your goods: contract manufacturer, contract sterilizer acting on your behalf, importer, or distributor. Then ask for the licence that attaches to that role. A supplier that answers with a certificate of registration to a quality standard has not answered the licensing question, and a supplier that answers with a medical device licence number for a device it does not manufacture has answered a question about somebody else's product.

Role in the chain Licence or authorisation that attaches What the buyer should hold
Manufacturer of a Class II, III or IV device Medical device licence, held by the manufacturer Licence number, and the device identifier it covers
Importer or seller of a device Establishment licence under section 44 of the regulations Establishment licence number, verified against the Health Canada listing
Contract sterilizer acting on the facility's behalf No separate device licence for the act of sterilization; the obligation travels through the quality agreement and the manufacturer's licence Written quality agreement naming the process, the validation standard and the record duties
Distributor of a Class I device Establishment licence, unless the exemptions apply Establishment licence number, plus the manufacturer's identity
Health care facility sterilizing for its own patients Exempt from the establishment licence requirement in that capacity Internal validation and record retention

Health Canada publishes the establishment licence framework in its guidance on medical device establishment licensing, and the licensing distinction itself is treated in more depth in DIN versus MDEL: which number proves what. The point to carry into an audit is that a licence number proves a role was registered; it does not prove a process was validated.

The twenty-item audit checklist

The checklist is organised by domain, and each item is written so that the answer is a document rather than a statement. The third column is the red flag — what an inadequate answer sounds like.

# Domain Item to verify Evidence that closes it Red flag
1 Licensing Legal role the supplier performs for your goods Named role in the quality agreement "We are licensed" with no role stated
2 Licensing Establishment licence number, where the role requires one Number, verified against the Health Canada listing A number that resolves to a different legal entity
3 Licensing Device licence coverage, where the supplier is the manufacturer Licence number with the device identifier A licence for an unrelated device family
4 Licensing Site address on the licence matches the site that will run the process Licence extract with the address Licence for head office, processing at an unlisted site
5 Quality system Certification to ISO 13485 with the scope covering sterilization as an outsourced process Certificate with scope text and accredited body Certificate with a scope that stops at "distribution"
6 Quality system Control of outsourced processes, as ISO 13485 requires of the organisation that outsources Documented supplier control procedure naming the sterilization process Outsourcing described only in a sales brochure
7 Quality system Purchasing and incoming control for packaging and indicators Purchase specifications, incoming inspection records No record of indicator lot verification
8 Process validation Validation report for the exact process family: ethylene oxide, moist heat, radiation or another agent Report naming the standard applied, ISO 11135, ISO 17665 or ISO 11137 A report for a different sterilization agent
9 Process validation Product families and packaging configurations covered by the validation Validation matrix listing families and pack formats "All products are covered" without a matrix
10 Process validation Load configuration and density limits within the validated envelope Load pattern drawings, maximum load definition Load pattern decided per shift
11 Process validation Requalification triggers and last requalification date Requalification procedure and the latest report Requalification only after a customer complaint
12 Process validation Biological indicator system used for routine control and its placement Indicator specification, PCD definition, placement drawing Indicator described only as "spore test"
13 Batch records Record for each load: cycle parameters, time, temperature, gas concentration or dose A redacted sample load record Summary sheets with no cycle identifiers
14 Batch records Release decision and the person who made it Signature and role on the release record Release by the same person who ran the cycle, undocumented
15 Traceability Chain from your lot number to the load, and from the load back to your lot Traceability sample traced both directions in front of you "We can find it if needed"
16 Traceability Retention period for load records and the storage location Retention policy with the period stated Records retained for a period shorter than your device shelf life
17 Change notice Notification duties for changes to process, packaging, site or equipment Change control procedure with customer notification clause No notification clause in the quality agreement
18 Change notice Prior approval requirement before a validated change takes effect Clause naming which changes need written approval Supplier may change the process at its discretion
19 Recall support Ability to identify all customers who received product from a named load Mock recall performed and timed Recall procedure with no exercised record
20 Recall support Complaint and incident records, and the duty to inform you of adverse events Complaint log sample, incident reporting clause Complaints handled internally with no customer notice

Twenty items is not a long audit; it is a two-hour document review if the supplier is organised, and a two-week exchange if it is not. The second outcome is itself a finding.

Which six items are stop-sign items?

Items 8, 9, 12, 15, 17 and 19 carry more weight than the rest, because each of them is a control that cannot be retrofitted after a problem appears.

Validation coverage (8 and 9) is the first. A sterilization process is validated for a defined product family in a defined packaging configuration at a defined load density. If your instrument set sits outside that envelope, the supplier is running your goods through a process that has been qualified for something else, and no amount of general certification changes that. The ethylene oxide validation questions a buyer should ask sets out what a report has to contain for one agent; the same structure applies to moist heat under ISO 17665 and to radiation under ISO 11137.

The routine biological indicator system (12) is the second. A biological indicator answers the lethality question for the load it was placed in, and its placement inside a process challenge device is what makes it representative. A supplier that cannot describe the device, the placement and the indicator specification is running a test rather than a control.

Traceability (15) is the third, and it is the one a recall actually depends on. The Medical Devices Regulations impose distribution record duties on manufacturers, importers and distributors — section 45 of the regulations is the provision that requires the records — and complaint records under section 57, incident reporting under section 59 and recall reporting under section 63 all presume that a load can be resolved to a list of customers. A mock recall performed in front of the auditor, with a stopwatch, converts a procedure into evidence.

Change notification (17) is the fourth, and it is the item most often missing from the quality agreement rather than from the quality system. A supplier with excellent change control internally, and no contractual duty to tell you, will change a packaging material and leave your validation statement describing the previous configuration.

Recall support (19) is the fifth. Ask when the last mock recall was run, how long it took, and what the recovery rate was. A supplier that has never run one is relying on the plan rather than on the practice.

The sixth is the pairing of 1 and 2: the legal role and the licence that attaches to it. Everything else in the audit presumes you know which entity is doing what.

What does the validation report have to say?

A validation report is a claim about a process, and the buyer's job is to check that the claim is scoped to the goods being sent. Four elements carry most of the weight.

Element What the report must state Why the buyer cares
Standard applied ISO 11135 for ethylene oxide, ISO 17665 for moist heat, ISO 11137 for radiation, with the edition identified The half-cycle or overkill approach and the acceptance criteria follow from the standard
Product family and packaging The families and pack formats inside the validated envelope Your set either sits inside the matrix or it does not
Load configuration Maximum load, load pattern, and the location of the process challenge devices Penetration depends on density and geometry, not on the chamber's rated capacity
Acceptance criteria Sterility assurance level and the biological indicator system used to demonstrate it The SAL is what the release decision rests on, and it is not interchangeable between device types

Two practical notes belong with that table. First, the packaging is part of the validated configuration: a change from a pouch to a wrap is a change to the process, which is why packaging validation under ISO 11607 runs alongside sterilization validation rather than after it. Second, the report's date matters less than its scope — an older report that covers your configuration is stronger evidence than a recent one that covers a different device family.

What does the quality agreement have to contain?

The quality agreement is where a commercial relationship becomes an auditable one. Five clauses do the work: the definition of the process and the standard it is validated against; the records the supplier will create, retain and produce on request, with retention periods; the change notification duty, including which changes require prior written approval; the deviation and complaint notification duty, with a time limit; and the recall cooperation duty, including the supplier's obligation to identify affected loads within a stated period.

A quality agreement without a notification time limit is a goodwill clause. The difference shows up in the first real event, when the question is not whether the supplier will call but how many days later.

For the device side of the relationship, the incoming-control questions overlap with the ones a clinic asks of any supplier, which the ISO 13485 supplier verification guide sets out in the language of a practice rather than a manufacturer. Health Canada's inspection programme for medical device establishments is worth reading for the same reason: it shows what an inspector asks for, and the audit list above is built to produce those answers.

What changes when the sterilizer is off-site?

Three things, and each has a cost that the purchase order usually omits.

The first is time in quarantine. Instruments sterilized off-site are not available until the load is released, and the release depends on the biological indicator result, which depends on the read time of the indicator system the supplier uses. A supplier running a 24-hour readout adds a day to the cycle of every set; a supplier running a rapid readout shortens it, at a different cost per test. The biological indicator formats compared across suppliers is the reference for the format question, and the 24-hour steam biological indicator is the format most facilities standardise on when the turnaround has to be predictable.

The second is packaging integrity in transit. A pouch that is validated for the sterilization process can still fail on the way back if it is compressed, and the outer packaging is part of what the facility has to inspect on receipt. The visible indicators that travel with the load — a Class 4 self-sealing pouch with a process indicator, or indicator tape on a wrapped set — record exposure, not sterility, and a facility that treats them as a release criterion has moved the decision to the wrong document.

The third is the record you keep at your end. A facility that receives sterilized goods still has to be able to answer, for any instrument in a patient's mouth, which load it came from and what that load's release evidence was. That means keeping the supplier's load identifier next to your own lot reference, not filing the delivery note in a folder and the certificate in another.

The field set that does that work — load identifier, cycle type, indicator lot, release decision and the person who made it — is the same one the compliance log centre runs in a browser without an account, and it prints as a blank sheet if the receiving bench works on paper. The wider document frame, including how the Canadian and United States monitoring requirements divide, sits at the sterilization compliance hub.

Class 4 self-sealing sterilization pouch, 2.5 x 4 inch, with external and internal process indicators and a write-on panel
A pouch indicator records that the pack was exposed to a cycle. For goods sterilized off-site, the release evidence has to travel with the load identifier, not only with the delivery note.
Three 24-hour steam biological indicators in clear tubes with red caps, labelled for Geobacillus stearothermophilus
The indicator system a contract sterilizer runs sets the turnaround for every load it processes. A 24-hour readout adds a day before release; that day belongs in the service agreement rather than in a surprise.

Buying packaging or monitoring consumables for a sterilized-goods workflow? Wholesale and multi-site ordering covers account setup, and the B2B wholesale collection lists the lines stocked for institutional buyers. Reselling? become a distributor.

Working through a supplier file of your own? Send the question with the document you are looking at, and you will get a written answer citing the regulation or standard it rests on. Ask your compliance question.

Related reading

Frequently Asked Questions

Does a contract sterilizer need its own medical device licence in Canada?

Not for the act of sterilization itself. The medical device licence attaches to the manufacturer of a Class II, III or IV device, and the establishment licence under section 44 of the Medical Devices Regulations attaches to the person who imports or sells a device. What a contract sterilizer owes the facility is a documented process: a validated cycle, batch records, a traceability chain and a quality agreement that assigns the record duties. A licence number presented in place of that documentation answers a different question.

How do we verify an establishment licence number?

Ask for the legal entity name and the site address, then check them against the Health Canada establishment licence listing rather than against the supplier's own certificate. The two failure modes are a number that belongs to a different legal entity in the same group, and a licence that covers a head office while processing happens at an address the licence does not name. Both are visible in a two-minute check.

Is ISO 13485 certification enough to qualify a contract sterilizer?

No. Certification tells you a quality system has been audited to a standard. It does not tell you that your product family and packaging configuration sit inside a validated sterilization envelope. Read the certificate's scope text, then ask for the validation report that names your product family, your pack format and the load configuration. The certificate and the validation report answer two different questions, and both have to be answered.

Can a supplier use one validation report for all its customers?

Only within the envelope the report defines. A validation is written for specific product families, packaging configurations and load densities; a report can legitimately cover several customers if their goods fall inside that matrix. What it cannot do is extend to a new pack format, a much denser load or a different packaging material without requalification. Item 9 on the checklist is the request for that matrix, and a supplier that cannot produce one is asking you to accept a general statement.

What should a mock recall prove?

That the supplier can go from a named load to a complete list of affected customers, and from a named customer back to the load, within a stated time and with a recovery rate they are willing to put in writing. Ask for the date of the last exercise, the time taken and the percentage of product accounted for. A recall procedure that has never been exercised is a plan; an exercised one is evidence, and only the second one is useful to you during an actual event.

How long should sterilization records be kept?

Long enough to cover the shelf life of the product plus the period in which a complaint or an incident could reasonably surface, and long enough to satisfy the retention clause in the quality agreement. In practice the retention period should be stated in the agreement, matched to your own device history file, and tested once by asking the supplier to retrieve a load record from the oldest year inside that window.

Does outsourcing sterilization change the facility's own obligations?

It changes who performs the process, not who answers for the outcome. A facility that sends instruments out still owes its patients a release decision, still has to keep the record that links an instrument to a load, and still has to be able to act on a recall. The supplier's certificate supports that work; it does not replace it.

Every CliniEco Medical product is manufactured under an ISO 13485 quality management system and distributed under Health Canada MDEL #35334. CliniEco Medical supplies sterilization packaging and monitoring consumables; we do not operate a contract sterilization service, and nothing in this article should be read as a recommendation of a particular provider.

Sources

Already working with clinics? Become a regional representative.