Quick facts
- A calibrator is a material used in a test system to establish points of reference for the measurement of substances in human specimens.
- In the United States it is a named entry. 21 CFR 862.1150, Calibrator, is Class II, with the product codes JIS, JIT, JIW and JIX.
- Canada keeps no named entry. A calibrator used in diagnosis or patient management is an IVDD at Class II under Part 2 Rule 4.
- Part 2 Rule 4 lifts the calibrator to Class III where the stated use reaches cancer screening, genetic testing, screening for congenital disorders in the fetus, a risk of death or severe disability from an erroneous result, disease staging, or drug-level monitoring with an imminent life-threatening decision.
- Part 2 Rule 7 sets the class of a calibrator used with another IVDD at the higher-risk class of the pair.
- Entries, classes and product codes below were checked against the eCFR, the Regulations and the openFDA classification database on 2026-10-15.
A clinical calibrator is the reference material a test system uses to establish the points against which a patient result is read. The United States names the material and places it in the special-controls class; Canada keeps no entry and classifies it as an in vitro diagnostic device, with a set of stated uses that lift the class. This article sets out both routes and the traceability record that goes with them, with the 120 mL sterile specimen containers used on the same bench.
What is a clinical calibrator?
It is a material with an assigned value that a test system reads so the system's output can be anchored to a known point. Before patient samples are measured, the calibrator is run, the instrument records the response, and the instrument's response curve is set against the assigned value. Without that step, a signal is only a number; with it, the number maps onto a concentration.
The US identification describes the purpose precisely: a calibrator is a device intended for medical purposes for use in a test system to establish points of reference that are used in the determination of values in the measurement of substances in human specimens. The same section points the reader to section 862.2, which governs the analytical performance of such materials.
What class is a calibrator in the United States?
It is a named entry. 21 CFR 862.1150 is titled Calibrator, and the identification reads: \"a calibrator is a device intended for medical purposes for use in a test system to establish points of reference that are used in the determination of values in the measurement of substances in human specimens.\" The regulation sets Class II (special controls), and the device is exempt from premarket notification under subpart E of part 807 subject to the stated limitations.
The openFDA device classification API returns four product codes against the section, and they separate the calibrator by how it is made: JIS for a primary calibrator, JIT for a secondary calibrator, JIW for a surrogate calibrator and JIX for a multi-analyte mixture. A laboratory comparing quotes should note which of the four the material is, because the traceability chain is not the same for each.
| Item | Detail |
|---|---|
| US regulation | 21 CFR 862.1150 - Calibrator |
| US class | Class II (special controls) |
| Product codes | JIS (primary), JIT (secondary), JIW (surrogate), JIX (multi-analyte mixture) |
| Stated intended use | Establish points of reference used to determine values in the measurement of substances in human specimens |
| Cross-reference in the entry | Section 862.2, analytical performance of such materials |
| Premarket route | Exempt from premarket notification under subpart E of part 807, subject to the stated limitations |
| Read on | eCFR identification text and openFDA classification, both read 2026-10-15 |
How does Canada classify a calibrator?
Canada keeps no named entry, so the class comes from Schedule 1 of the Medical Devices Regulations. A calibrator is an in vitro diagnostic device, and Part 2, Rule 4 classifies it: \"An IVDD that is not subject to rules 1 to 3 and that is intended to be used in diagnosis or patient management is classified as Class II, unless it falls into one of the following categories, in which case it is classified as Class III.\" The categories that lift it are worth reading against the maker's intended use, because they are the difference between a Class II and a Class III classification: (a) screening for or diagnosis of cancer; (b) genetic testing; (c) screening for congenital disorders in the fetus; (d) a risk that an erroneous diagnostic result would cause death or severe disability to the patient or the patient's offspring; (e) disease staging; and (f) monitoring of drug, substance or biological-component levels where an erroneous result leads to a patient-management decision resulting in an imminent life-threatening situation.
Part 2, Rule 7 then handles the calibrator used with a companion device: \"In cases where an IVDD, including its analyzers, reagents and software, is intended to be used with another IVDD, the class of both IVDDs will be that of the IVDD in the class representing the higher risk.\" A calibrator meant for an analyser therefore takes the class of the analyser where that is higher than the calibrator's own.
Two further Part 2 rules are read before a near-patient sale. Rule 6 classifies a near patient IVDD as Class III. Rule 9 keeps a short table of named exceptions, including a near patient device for pregnancy or fertility testing at Class II and one for determining cholesterol level at Class II.
| Item | Canada | United States |
|---|---|---|
| Named entry | None; classified by rule | 862.1150 - Calibrator |
| Class | Class II (Part 2 Rule 4, IVDD used in diagnosis or patient management) | Class II (special controls) |
| Governing text | Schedule 1, Part 2, Rules 4, 6 and 7 | 21 CFR 862.1150 |
| Higher-class fork | Rule 4(a)-(f) to Class III; Rule 6 to Class III for near patient use | Special controls set for the device |
| With a companion device | Rule 7 takes the higher class of the two IVDDs | Separate product codes for the calibrator types |
| Licence route | Device licence for the Class II material | Class II route, subject to the stated exemption |
Why do the two countries use different words for the same class?
The classes match, but the machinery does not. The United States wrote a named entry with special controls and four product codes that separate calibrators by how they are made. Canada wrote a general rule for in vitro diagnostic devices used in diagnosis or patient management, then added a list of stated uses that lift the class, and a special rule that reads a calibrator together with the device it is intended for.
That difference matters in practice. A calibrator for a routine chemistry panel sits at Class II on both sides. The same calibrator, if its stated use reaches one of the Part 2 Rule 4 categories, or if it is intended for near-patient use, can sit at Class III in Canada while the US entry still reads Class II. The words in the intended-use statement, not the physical form of the material, are what decide it.
What should a laboratory check before ordering one?
Four checks. First, establish which type the maker supplies - primary, secondary, surrogate or multi-analyte mixture - because the product code and the traceability chain follow from that. Second, confirm the assigned values and their uncertainty the maker states, and the reference the values are traceable to. Third, read the intended-use statement for any of the Part 2 Rule 4 categories, since those change the Canadian class. Fourth, confirm the storage, shelf-life and handling instructions, because a calibrator that drifts silently moves every result read against it.
A clinical laboratory also reorders the consumables used at the same bench. Clinics that stock for a whole practice can order through the wholesale programme and request a bulk quote for a standing or annual order; the 120 mL sterile specimen containers sits in the same catalogue. Consumables for this line are listed under diagnostic laboratories. Reselling? become a distributor.
How does the class affect the calibration record?
The class sets the market-entry path; the record is set by the laboratory quality system. ISO 15189 frames the requirements for quality and competence in medical laboratories, and ISO 17511 is the framework for the metrological traceability of the values assigned to calibrators and control materials. That is the standard a laboratory cites when it states what a calibrator's assigned value is traceable to.
The working record is short: the calibrator lot, its assigned values, the date it was run, the acceptance criteria and the outcome. Keeping it beside the patient results it anchors is what lets a review retrace a result to the point of reference it was read against.
Sources
- openFDA device classification API
- Medical Devices Regulations, SOR/98-282, full text and Schedule 1
- US FDA, medical device databases
- US FDA, overview of device regulation
- Health Canada, medical devices
- Health Canada, establishment licensing
- ISO 15189:2022, medical laboratories, requirements for quality and competence
- ISO 17511:2020, metrological traceability of values assigned to calibrators
- ISO 13485:2016, medical devices quality management
- ISO 14971:2019, application of risk management to medical devices
- Clinical and Laboratory Standards Institute
- World Health Organization
- US CDC, laboratory quality
- Public Health Ontario, infection prevention and control
- Standards Council of Canada
- CCOHS, OSH answers
A printable calibration sheet. The analyser, the calibrator lot, the assigned values, the run date and the outcome fit on one page you can print and file with the patient results. Open the compliance log centre and take the blank sheet: no account and no sign-up, and print a pad for the bench.
Make calibration a dated set. Enter the laboratory name, the analyser and the acceptance rule once, and the sterilization log generator produces dated sheets that follow the calibration schedule through the year.
Ask a compliance specialist. A classification question usually turns on how the device is used, not only on its name. Ask a compliance specialist — you get a written answer specific to your equipment and province, with the regulation or standard it is based on cited.
Related reading
- Clinical HPLC systems in Canada vs the US
- Automated blood grouping systems in Canada vs the US
- MALDI-TOF identification systems in Canada vs the US
CliniEco Medical supplies eye care, laboratory and dental consumables of the kind described in this article. MDEL #35334. This article is written for optometry, laboratory and dental procurement professionals and is not legal advice; the class of a device and the records a practice keeps belong to the manufacturer and to the requirements that apply to it.
Frequently Asked Questions
What class is a clinical calibrator in the United States?
Class II (special controls). It is a named entry at 21 CFR 862.1150, with product codes for primary, secondary, surrogate and multi-analyte mixture calibrators.
What class is it in Canada?
Class II, under Part 2 Rule 4 of Schedule 1, because a calibrator is an in vitro diagnostic device used in diagnosis or patient management. Canada keeps no named entry for it.
When would a calibrator reach Class III in Canada?
Where its stated use falls into one of the Part 2 Rule 4 categories - cancer screening or diagnosis, genetic testing, fetal congenital-disorder screening, a risk of death or severe disability from an erroneous result, disease staging, or drug-level monitoring with an imminent life-threatening decision - or where it is a near patient IVDD under Rule 6.
What happens if the calibrator is used with an analyser?
Part 2 Rule 7 applies: where an IVDD is intended to be used with another IVDD, both take the class of the higher-risk device. A calibrator therefore takes the analyser's class where that class is higher.
What standard covers the values assigned to a calibrator?
ISO 17511 is the framework for the metrological traceability of values assigned to calibrators and control materials, and ISO 15189 frames the laboratory's own quality and competence requirements.
Does the class change how calibration is recorded?
No. The class sets the market-entry path. The record is set by the laboratory quality system: the calibrator lot, assigned values, run date, acceptance criteria and outcome, kept with the results it anchors.