Which Ymarda Ergo Angled Dental Loupes Do Dental Laboratories in Nova Scotia Order? Sizes and Case Formats
A Nova Scotia dental laboratory is usually a small corporation with a registered dental technician at the bench and a second technician hired when the work justifies it. That shape decides the loupe order: the buyer is specifying for a bench that may be shared, in a business where the person signing off is also the person using the optics.
The order itself is simpler than it looks, because the Ymarda Ergo is a single optical build. The CliniEco Ergo angled dental loupes, 3.5x with adjustable PD is the same configuration sold from Canadian stock: angled prismatic barrels, adjustable interpupillary distance, a headlight mount on the frame, and no fitting visit.
Which Ymarda Ergo build do Nova Scotia laboratories order?
One build, and the choices sit around it rather than inside it. Magnification is fixed at 3.5x. The optical path is angled so the barrels look down at the work while the neck stays upright, which is the reason a laboratory buys angled optics instead of flip-up ones: at a bench the technician holds a posture for hours, and a frame that requires the head to tilt converts that into neck strain by mid-afternoon.
What the buyer chooses is the working distance, and that is where an order goes wrong. Everything else — the frame, the case, the cloth, the headlight mount — arrives as standard.
What working distance should the order specify?

Four settings are built: 360 mm, 460 mm, 520 mm and 560 mm. The setting is fixed for the life of the unit, so it has to be measured rather than guessed, and it should be measured the way the technician actually sits rather than standing at a counter.
| Setting | Who it suits | Consequence of getting it wrong |
|---|---|---|
| 360 mm | close bench work, shorter torsos, seated magnifier posture | leaning in to focus, shoulders forward |
| 460 mm | the common middle setting for a finishing bench | the most forgiving of the four |
| 520 mm | upright posture with the work further out | arms extended, elbows unsupported |
| 560 mm | tall technicians and benches set high | the field is small and the reach is long |
The practical test takes a minute. Sit as the work is done, let the arm hang, then look at the hand: the eye-to-hand distance is the working distance to order. Adding a headlight does not change it, because the light mounts on the frame and follows the optics.
What ships in one case, and how does a laboratory order for several technicians?
One unit per case: frame, carry case and cleaning cloth. A three-technician bench orders three units and specifies a working distance for each, and the case format means each pair stays with its user rather than migrating between benches. The interpupillary distance adjusts on the frame, so a spare pair can be handed to a locum who works at the same distance without a rebuild.

The headlight is the one accessory worth deciding at the same time. The frame has the clip built in, and the Core wireless headlight, 32,000 lux at 40 cm and 11.8 g at the lamp head mounts without an adapter. Buying the light later works; buying a light that does not fit the mount is the expensive version of the same decision.
Are angled loupes acceptable as eye protection at the bench?
No, and this is the point that gets argued in laboratories. The CCOHS guidance on eye and face protectors refers to CSA Z94.3.1 for selection, use and maintenance, and certified protectors are marked on the lens, the frame or the side shield. A loupe frame carries no such marking, and the optical barrels are open at the sides. A technician trimming, grinding or polishing still needs safety spectacles or a face shield as well, and the loupes sit behind them.
How does a laboratory place a repeat order?
By the numbers on the frame, not by the product name. Record the working distance setting, the serial of each unit, and which technician each belongs to; a repeat order in eighteen months is then a list rather than a memory exercise. The Ergo 3.5x with the matched headlight is the version to quote when the second bench also needs light, since the pairing is checked before it ships rather than assembled at the bench.
One regulatory note sits behind the ordering contact. Under the Nova Scotia Dental Technicians Act, R.S.N.S. 1989, c. 126, a registered technician has the right to use the designation "Registered Dental Technician" and may describe the business as a dental laboratory, and section 10 requires that a corporation operating a laboratory have a majority of its directors registered, a majority of each class of shares held by registered technicians, and a registered technician in charge of the actual operations. In practice the person approving a bench purchase is one of those directors, which is why the specification conversation is short.
Ordering for a laboratory or a multi-site group? Wholesale and multi-site ordering covers case pricing and account setup, and the B2B wholesale collection lists the lines stocked for institutional buyers. Reselling? become a distributor.
Working in a dental laboratory? The dental practice and laboratory supply page groups the magnification, lighting and bench consumables ordered on the same cycle.
References
- Dental Technicians Act, R.S.N.S. 1989, c. 126, sections 7 and 10 — Nova Scotia Legislature (consolidated text on CanLII) (checked 12 November 2026)
- Eye and face protectors, OSH Answers — Canadian Centre for Occupational Health and Safety (checked 12 November 2026)
Printable companion: the clinic supply and cost planner holds the per-technician specification in one table, which is what a laboratory needs when a second bench is added.
Want the frame numbers on the same sheet as the rest of the bench equipment? The free log and record set includes an equipment sheet the serials can be copied onto.
Related Reading
- Dental Loupes in Canada: 2.5x vs 3.5x, Working Distance and What a Clinic Actually Needs
- Custom Loupes Prescription and Fitting: How Canadian Dentists Order
Frequently Asked Questions
Why would a laboratory choose angled rather than flip-up loupes?
Angled optics let the bench technician keep the neck upright and look down through the barrels. Flip-up optics sit straight ahead, so the head tilts to find the field.
Does the frame need a fitting appointment?
No impression and no fitting visit. Interpupillary distance adjusts on the frame, and the working distance is set when the unit is built.
Can two technicians share one pair?
Yes if they work at the same working distance. The PD adjusts per user, the working distance does not move between them.
What is in the case besides the optics?
The frame, a carry case and a cleaning cloth. A headlight clips to the mount already on the frame.
Last updated: November 2026. CliniEco Medical is a licensed medical device establishment (MDEL #35334).