What Pillow and Table Protection Does a Canadian Clinic Need per Patient?
Two patients, one room, twenty minutes apart. The first leaves the table dry and the pillow untouched. The second has a procedure that drains, and the pillow is the surface everyone forgets, because the table was covered and the pillow was not. The room gets turned around either way; only one of those turnarounds needed a different set of materials.
Per-patient protection is the least glamorous line in a clinic budget and one of the easiest to get wrong in both directions. Too little and staff improvise with a second length of paper that absorbs nothing; too much and a cupboard fills with case quantities of a sheet weight nobody chose. The useful number is the count of layers one patient actually consumes, converted into a par a room can be restocked against.
This guide works from the table up. It counts the layers, converts the count into roll and case arithmetic, and sets out what a Canadian clinic has to keep on the label and in the waste stream. It also separates two things that are routinely confused: the paper that covers a table and the sheet that covers a pillow are not the same product, and they do not fail in the same way.
What counts as one patient's protection set?
Three layers, of which two are routine. The table surface takes a paper or a sheet. The pillow takes its own layer. The third layer, an absorbent pad, is conditional: it appears when the visit involves drainage, a wet procedure or a patient who cannot be moved easily.
The distinction that matters for stock control is contact. Paper over the table is a hygiene layer: it is changed between patients, it is not liquid-proof, and it is inexpensive enough that changing it is never the bottleneck. A sheet is a barrier layer: it covers more surface, it drapes, and it is what a clinic reaches for when the table is padded, when the patient lies on a pillow, or when a longer appointment means the paper would tear. A room that covers both jobs from a single stock line does it with a disposable non-woven bed sheet, 36 by 80 inches, folded over the pillow and laid across the table.
| Layer | Format | What it contacts | When it is required |
|---|---|---|---|
| Table surface | Perforated roll or 50-sheet box | Table pad, patient's clothing or skin | Every patient, changed between visits |
| Pillow | Folded disposable sheet or dedicated cover | Pillow, patient's head and hair | Every patient, whenever a pillow is used |
| Absorbent third layer | Underpad, 30 by 36 inches or 60 by 90 cm | Table or couch under a draining site | Wet procedures, drainage, incontinence risk |
How much table paper does one patient use?
One continuous draw, taken from the head of the table to where the patient's legs end, is the assumption most clinics work to, and 36 inches is a reasonable planning figure for a standard table. The arithmetic from there is simple and worth doing once, because roll length is where two formats that look similar turn out to be very different purchases.

An 18-inch roll at 225 feet holds 2,700 inches. At 36 inches per patient that is about 75 patients per roll, and a case of 12 rolls covers roughly 900 patients. A 21-inch roll at 125 feet holds 1,500 inches, which is about 41 patients per roll; a nine-roll pack covers about 375.
| Format | Length per roll | Patients per roll at 36 inches | Pack | Patients per pack |
|---|---|---|---|---|
| 18 inch by 225 feet, smooth | 2,700 inches | about 75 | Case of 12 rolls | about 900 |
| 21 inch by 125 feet, perforated | 1,500 inches | about 41 | Pack of 9 rolls | about 375 |
| 18 inch by 50-sheet box, perforated | 50 draws per box | 50, one draw each | Eight-box pack | about 400 |
| 21 inch by 200 feet, smooth | 2,400 inches | about 66 | Single roll or case | depends on case |
Two conclusions follow, and both are counter-intuitive. The narrow roll is not the smaller purchase: 18-inch by 225 feet delivers more patients per roll than 21-inch by 125 feet, because length matters more than width when the draw is fixed. And a perforated box removes the "how much did I pull" variable entirely.
Width still matters. A 21-inch roll suits a wide table where a patient's arms rest outside an 18-inch width, because paper that does not cover the contact area gets doubled, which halves the patients per roll without changing the label on the case. An 18-inch perforated exam table roll, 400 sheets across eight 50-sheet boxes is the format for a room where the draw is predictable, and a smooth 18-inch by 225-foot table paper, case of 12 rolls is the format for a clinic that wants the larger patient count per case.
What protects the pillow, a cover or the same sheet?
The same stock, folded. A dedicated pillow cover is optional; a layer that can be changed in the time between two patients is not. What fails on a pillow is not absorbency, it is geometry: a flat length of paper slides off the moment a patient turns their head, and a pillow that has been used without a layer is the surface most likely to be reused because it looks clean.
A disposable non-woven bed sheet, 36 by 80 inches, folds over a standard pillow with enough left to tuck, which is why clinics that stock one sheet line use it for both the table and the pillow rather than buying a separate pillow product. One stock line, two jobs, one lot to rotate.
Drainage changes the answer. When a visit is likely to wet through, the layer over the pillow needs an absorbent core rather than a non-woven surface, and a five-layer underpad at 60 by 90 cm does that job under a head or under a hip. An underpad at 30 by 36 inches is the size for a table rather than a bed, and it is the line that keeps a procedure room from going out of service over a spill.

Why does the sheet's GSM matter more than its size?
Because size decides fit and GSM decides whether the layer does anything. GSM is mass per unit area, and for nonwovens it is measured under ISO 9073-1, which is why the number on a case is comparable between suppliers while a phrase like "heavy duty" is not. Thickness is a separate property, measured under ISO 9073-2, and the two do not move together: a calendered sheet can be thin and dense, a lofted one thick and light.
The weight sets three behaviours a clinic notices within a week. A lighter sheet drapes and tucks but wicks moisture through. A heavier sheet holds a spill long enough for the visit to finish but is stiffer and needs a wider table. The weight also changes the count per case, because a case is sold by piece.
For a clinic, the useful rule is to match the weight to the visit rather than to the budget line. A routine examination on intact skin needs a hygiene layer. A procedure with a wet field needs a barrier plus an absorbent third layer. Buying the heavier sheet for every room and the lighter sheet for the procedure room inverts the requirement and costs more in the room that needed less.
Material held against skin also sits in the biological evaluation frame. ISO 10993-1 sets out how a contact category drives testing, and ISO 10993-5 and ISO 10993-10 cover cytotoxicity and skin sensitisation. Those tests belong to the manufacturer's file, not the clinic's, which is why a buying sheet names the manufacturer and the material.
What has to be on the label, and where does the used sheet go?
Start with what the product is. A non-woven sheet sold as a sheet is not licensed as a medical device, because the Food and Drugs Act definition of a device turns on the medical purpose the article is manufactured for. The moment the packaging claims a medical purpose, the article moves into the scope of the Medical Devices Regulations and the establishment that imports it needs a licence. The establishment that imports it needs an establishment licence, which is why the importer's number belongs on the buying file. CliniEco Medical operates under MDEL #35334.
For a buyer that distinction explains why one carton carries a lot number, an expiry and a bilingual label, and the carton beside it carries a size and a count. Filing the number of the establishment you buy from gives you a field to check when a notice appears on the recalls and safety alerts feed.

The waste route follows the same logic as any other disposable in the room: the provincial test is saturation, not contact. A sheet saturated with blood is biomedical waste under the requirements reflected in CSA Z317.10 and leaves on a hazardous waste manifest recorded through the Hazardous Waste Information Network. A dry sheet from a routine visit is general waste. Sorting by "it touched a patient" over-classifies every sheet in the building and shows up as extra pickups.
Cleaning between patients is a separate obligation from the disposable layer, and it does not disappear because the sheet was changed. Public Health Ontario publishes environmental cleaning guidance for health care settings, and the working principle is that the surface a patient contacts is cleaned between patients, whether or not a disposable layer sat on it.
How many patients does one case actually cover?
Take a clinic running 60 patients a week across three rooms, with one 36-inch draw and one pillow layer per patient. Weekly consumption is 2,160 inches of paper, which is 60 yards, and one 18-inch by 225-foot roll covers about 75 patients, so the clinic consumes roughly four rolls a month. A case of 12 rolls is therefore about three months of paper.
| Item | Driver | Weekly use | Four-week cover | Safety at 25 per cent | Par | Rounded order |
|---|---|---|---|---|---|---|
| Table paper, 18 inch by 225 feet | 36 inches per patient | 2,160 inches | 8,640 inches | 2,160 inches | 10,800 inches, 4 rolls | 1 case of 12 at each review |
| Pillow layers, 36 by 80 inches | 1 sheet per patient | 60 sheets | 240 sheets | 60 sheets | 300 sheets | convert at the pack count on the case |
| Underpads, 30 by 36 inches | 1 per draining visit, about 6 a week | 6 | 24 | 6 | 30 | 1 pack, rotated by lot |
| Perforated box, 50 sheets | 1 draw per patient in the procedure room | 50 | 200 | 50 | 250 | 5 boxes per review |
The pillow layer is the line most often under-ordered, because it is counted as part of the table rather than as its own consumption. A clinic that counts paper only will cover the table and improvise the pillow, and the improvisation is where a reused pillow comes from.
The last column is the one used under time pressure, so write it in packs rather than units: "300 sheets" sends someone to a conversion, "five boxes for the procedure room" does not.
When should the per-patient assumption be re-checked?
Quarterly, and immediately after a change in table width, service mix, room count or case pack count. Each of those changes the count without changing the sheet that describes it.
Table width is the quiet one. Moving a room from an 18-inch to a 21-inch roll, or adding a wider treatment couch for a new service, changes the draw length and therefore the patients per roll. Service mix works the same way: a clinic that adds a wet procedure changes its underpad consumption rather than its paper consumption, and a par sheet that only tracks paper will not show it.
*A note on scope:* this article covers per-patient materials and the Canadian labelling and waste framework behind them. It does not replace a clinic's own written room-turnover procedure, which should name who changes which layer and what gets recorded.
Running a family practice or a multi-room clinic? The family practice and general clinic supplies page groups the table, pillow and absorbent lines that a room turnover actually consumes, and the related reading below covers how often each layer is changed.
Ordering for a clinic, lab or care home? Wholesale and multi-site ordering covers case pricing and account setup, and the B2B wholesale collection lists the lines stocked for institutional buyers. Reselling? become a distributor.
References
- ISO 9073-1:2023 — Textiles, test methods for nonwovens, determination of mass per unit area (checked 6 November 2026)
- ISO 9073-2:1995 — Textiles, test methods for nonwovens, determination of thickness (checked 6 November 2026)
- ISO 10993-1:2025 — Biological evaluation of medical devices, evaluation and testing within a risk management process (checked 6 November 2026)
- ISO 10993-5:2009 — Biological evaluation of medical devices, tests for in vitro cytotoxicity (checked 6 November 2026)
- ISO 10993-10:2021 — Biological evaluation of medical devices, tests for skin sensitization (checked 6 November 2026)
- ISO 13485:2016 — Medical devices, quality management systems, requirements for regulatory purposes (checked 6 November 2026)
- ISO 14971:2019 — Medical devices, application of risk management to medical devices (checked 6 November 2026)
- Medical Devices Regulations, SOR/98-282 (checked 6 November 2026)
- Food and Drugs Act, R.S.C. 1985, c. F-27, section 2 definitions (checked 6 November 2026)
- Canada Consumer Product Safety Act, S.C. 2010, c. 21 (checked 6 November 2026)
- Health Canada — Medical devices (checked 6 November 2026)
- Public Health Ontario — Environmental cleaning (checked 6 November 2026)
- CCOHS — Occupational dermatitis (checked 6 November 2026)
- CCOHS — Personal protective equipment, gloves (checked 6 November 2026)
- Recalls and safety alerts, Government of Canada (checked 6 November 2026)
- Ontario Ministry of the Environment — Hazardous Waste Information Network (checked 6 November 2026)
Printable companion: the per-patient barrier worksheet uses the same columns as the tables below, so a room count can be written down and handed to whoever places the order.
Working out a quarter rather than a week? The clinic supply and cost planner turns patients per day into rolls, sheets and pads per quarter.
Related Reading
- Exam Table Paper as a Barrier: Sheet Changes, Width Choice and Case Math for Canadian Clinics
- Exam Table Hygiene: How Often to Change Paper Between Patients
- Disposable Bed Sheets: GSM, Size and When Canadian Clinics Use Them
Frequently Asked Questions
What protection does a clinic need per patient on an exam table?
Two layers and one conditional third. Paper or a sheet over the table surface, a separate layer over the pillow, and an absorbent pad only when the visit involves drainage or a wet procedure.
Is exam table paper enough as a barrier?
For a dry visit on intact skin, yes. It is a hygiene layer, not a liquid-proof membrane, so a visit that wets the paper needs a sheet or an underpad underneath rather than a second length of paper.
Should the pillow have its own cover?
The pillow needs its own layer, whether that is a folded disposable sheet or a dedicated cover. Paper alone slides off a pillow the moment a patient turns, and a pillow that is not covered is the surface most likely to be reused without being changed.
How many patients does one roll of table paper cover?
An 18-inch by 225-foot roll holds 2,700 inches, which at 36 inches per patient is about 75 patients. A 21-inch by 125-foot roll holds 1,500 inches, about 41 patients at the same draw.
What GSM should a disposable sheet be?
Heavy enough that it does not wick through during the visit it was made for. GSM is a mass per unit area measured under ISO 9073-1, so the number on the case is comparable between suppliers, while thickness sits in ISO 9073-2.
Do disposable sheets have to be licensed as medical devices?
Not when they are sold as sheets. The Food and Drugs Act definition of a device turns on the medical purpose the article is manufactured for, so the claim on the packaging is what decides whether a licence applies.
Where does a used sheet go, general waste or biomedical waste?
The provincial test is saturation, not contact. A sheet saturated with blood follows the health care waste rules reflected in CSA Z317.10 and moves on a hazardous waste manifest; a dry sheet from a routine visit does not.
How do you set a par level for sheets and rolls?
Count the per-patient draw, multiply by patients per week, add a safety margin of about a quarter, then round up to whole cases. Review the figure whenever table width, service mix or case pack count changes.
Last updated: October 2026. CliniEco Medical is a licensed medical device establishment (MDEL #35334).