What maintenance and documentation apply to eyewash stations in Canadian workplaces?
A sanitation supervisor at an Abbotsford, British Columbia food plant keeps two rinse bottles in a wall tray beside the chlorinated cleaner. When a WorkSafeBC officer asks for the test record, the clipboard shows three dates and nothing from the past five months. The bottles were never empty; the record was never treated as part of the equipment.
The CliniEco wall-mount eye wash station is the hardware half of that pairing. The other half is the page in the log showing when the unit was checked.
Which law actually requires the station?
Provincial occupational health and safety law, not a national code. Ontario's Industrial Establishments regulation, s. 124(1), requires eye wash facilities, emergency showers and flushing fluids where a worker works with, or is likely exposed to, a hazardous biological or chemical agent that could injure the eye or skin. British Columbia asks for the same equipment where eyes or skin may be exposed to harmful or corrosive materials (s. 5.85), and requires the choice to follow a documented risk assessment (s. 5.88) against Table 5-2.
Is there a Canadian standard for eyewash maintenance?
No. CCOHS states that no Canadian standard covers the design or placement of eyewash stations or emergency showers, and that ANSI/ISEA Z358.1-2014 (R2020) is generally used as a guide. That explains most of the confusion in the file: the law sets a narrow floor, the equipment standard sets the habit, and the manufacturer sets what is unit-specific.

Which province requires what?
| Requirement | British Columbia | Ontario |
|---|---|---|
| Flush test frequency | Full-flow test at least once a month, long enough to flush the branch line (s. 5.93(2)) | Not specified in s. 124 |
| Where the unit goes | 5 seconds and 6 m for high risk; 10 seconds and 30 m for moderate risk (Table 5-3) | Conspicuous place near where the agent is kept (s. 124(2)) |
| Signage | Location and directions for use (s. 5.92) | Label plus instructions displayed on the unit (s. 124(2)) |
| Water temperature | Tempered, defined in Part 5 as 15-30 °C | Not specified |
| Worker training | Required (s. 5.94) | General duty to instruct workers |
This row is where the provincial text parts company with the American standard: ANSI defines tepid as 16-38 °C, British Columbia defines tempered as 15-30 °C. A unit running at 33 °C passes the standard and fails the provincial definition.
What belongs on the test record?
| Field | Why it is asked for |
|---|---|
| Unit identifier and location | ties the entry to a station on the floor plan |
| Date and time tested | shows the gap, which is the finding |
| Person who performed the test | one name and signature, no initials |
| Water temperature | supports or contradicts the tempered range |
| Fault found and work order | proves a failed unit left service |

How often should a plumbed unit be activated?
Weekly, if it was installed to the standard CCOHS cites, because ANSI suggests weekly activation to limit sediment and stagnant water. Monthly at minimum, because that is what British Columbia enforces. Recording weekly satisfies both; recording only the month leaves the branch still for four weeks. Run the test long enough to clear the branch, not to wet the bowl.
What about self-contained and portable units?
They carry a finite charge. CCOHS notes the bladder expires and must be replaced once activated, and the unit must still deliver 15 minutes of fluid. British Columbia allows portable units at transient worksites with no water supply, flushed for 15 minutes where injury risk is high or moderate (s. 5.90).
Cold is the other failure mode: CCOHS records plumbed indoor systems at 2-7 °C in cold climates, below any tempered range, and s. 5.95 requires freeze protection for the unit and its piping.
Ordering for a plant or multi-site operator? Wholesale and multi-site ordering covers case pricing and account setup; the B2B wholesale collection lists institutional lines. Reselling? become a distributor.
Running a food or beverage plant? See our food manufacturing and sanitation supplies.
Printable companion: the free compliance log set carries a monthly eyewash test sheet with the fields above; the supply and cost planner turns station counts into packs per quarter.
References
- Occupational Health and Safety Regulation, B.C. Reg. 296/97, Part 5 — WorkSafeBC (checked 12 November 2026)
- R.R.O. 1990, Reg. 851, Industrial Establishments, s. 124 — Ontario (checked 12 November 2026)
- Emergency Showers and Eyewash Stations — CCOHS (checked 12 November 2026)
Related Reading
- Eyewash Station Maintenance in Canada: Flush, Test and Record
- Eyewash Stations in Canada vs the US: What ANSI Z358.1 Governs
- Eye Wash Solution in Canada vs the US: Which Fluid Rules Apply
Frequently Asked Questions
Does Canadian law require a weekly eyewash flush?
No. British Columbia requires a plumbed unit to be full-flow tested at least once a month; weekly activation is a recommendation in the equipment standard, not a legal frequency.
Can a wall-mounted bottle unit replace a plumbed eyewash station?
Only where the risk assessment allows it. British Columbia treats a portable self-contained unit as the answer for a transient worksite with no water supply, and a personal unit as supplementary to an emergency eyewash facility.
How long should a test record be kept?
Neither regulation states a retention period, so the period belongs in the site health and safety program and should match how long incident and maintenance files are kept.
Last updated: November 2026. CliniEco Medical is a licensed medical device establishment (MDEL #35334).