What Documentation Applies to CAD/CAM Milling and Resin Handling in a Canadian Dental Lab?

Three-layer paper and PE dental bibs stacked for use as a bench cover in a dental laboratory

What Documentation Applies to CAD/CAM Milling and Resin Handling in a Canadian Dental Lab?

A dental laboratory in Mississauga runs three milling units and a resin printer, and it answers two separate audit questions: one trail follows the machine, the other follows the resin. They meet only in the case file, and the question is which sheet shows the material was handled as instructed. The bench cover is where the trail starts: a 17 by 24 inch multi-layer patient bib, 500 per case is consumed per case, and so is the paperwork behind it.

Which documents does resin handling actually generate?

Document Issued by Where it has to be retrievable
Safety data sheet, 16 sections Resin or monomer supplier At the bench where it is poured
Biological evaluation Material or device maker Design file for each device family
Processing instructions Equipment maker With the unit or the tooling
Case record The laboratory By case number

Resin handling is a hazardous materials question before it is a device question: the supplier provides the safety data sheet and the workplace keeps it available to the people using it, which in a lab means the bench, not an office cabinet.

Aurelia number 2 cotton rolls carton on a dental laboratory supply shelf

What does the milling unit documentation have to cover?

The unit is maintained rather than processed: service dates, coolant and filter changes and calibration belong with the serial number. The burs that touch a restoration are a different category, and ISO 17664-1:2021 sets what the maker must state about cleaning, disinfection and sterilization for them. A procedure built from that document survives an audit better than one built from the last lab's habit.

How is resin biological safety documented?

Three-layer paper and PE dental bibs stacked for use as a bench cover in a dental laboratory

The laboratory does not run biocompatibility testing. It holds the evaluation the material maker produced, and ISO 10993-1:2025 is the framework that evaluation follows; the 2018 edition is withdrawn, so a declaration still quoting 2018 describes a superseded framework. The declaration covers a material used as instructed, and blended or reused monomer sits outside it.

What case records does a Canadian dental lab keep?

Case number, material and lot, the unit that produced the work, and who ran the job. Restorations are made to a prescription, so the prescription and the handling instruction that travelled with the impression are part of the file. ISO 13485:2016, the quality frame most labs are asked to show, treats the case file rather than the invoice as the unit of traceability. Stocked consumables follow the same rule, including the 1 lb canister of alginate impression material, whose lot ties back to a case.

Where does cured resin waste go?

Cured trimmings and failed prints are solid waste. Liquid resin and wash solvent go where the safety data sheet says, which is not the sink and not the red bag. A 1,000-cap case of 24-inch bouffant caps and the bench barrier belong to the same routine; segregating at the bench costs a bin, and finding the mistake after the tote is lifted costs a conversation.

Sending work to a laboratory? The dental practice supplies page covers chairside items that travel with the case; the clinic consumables range lists what a bench restocks weekly.

Ordering for a clinic, lab or care home? Wholesale and multi-site ordering covers case pricing and account setup, and the B2B wholesale collection lists the lines stocked for institutional buyers. Reselling? become a distributor.

References

  1. Health and safety data sheets under WHMIS 2015 (checked 4 November 2026)
  2. ISO 10993-1:2025 — Biological evaluation of medical devices, Part 1 (checked 4 November 2026)
  3. ISO 17664-1:2021 — Information to be provided by the manufacturer for processing (checked 4 November 2026)

Printable companion: the free equipment and lot record templates hold the fields a lab case file needs, so the sheet is filled in at the bench instead of rebuilt a year later.

Sizing a quarterly order for the bench? The clinic supply planner turns cases per week into bibs, barriers and consumable quantities.

Not sure how this applies to your own setup? Ask a sterilization compliance specialist — you’ll get a written answer specific to your equipment and province, with the regulation or standard cited.

Related Reading

Frequently Asked Questions

Which document does a dental lab need for the resin itself?

A safety data sheet in the WHMIS 2015 sixteen-section format from the supplier, kept where the resin is actually poured. Sections 8 and 13 cover skin contact controls and disposal.

Is the milling unit sterilized between cases?

No. The unit is cleaned and maintained on the maker's schedule, with dates recorded against its serial number. Only items that contact the patient or the restoration follow the processing instructions.

Which ISO 10993 edition should a supplier declaration cite?

ISO 10993-1:2025 is current and the 2018 edition is withdrawn, so ask for a declaration citing the current year before filing it in a design folder.

Do lab-made restorations need a medical device licence in Canada?

Custom-made devices are made to a prescription for a named patient, so the lab holds the prescription, the material lot and the case record instead of a device licence. The traceability is the evidence.

Last updated: October 2026. CliniEco Medical is a licensed medical device establishment (MDEL #35334).

Already working with clinics? Become a regional representative.