How Often Must US vs Canadian Clinics Run Sterilizer Testing? Which Bowie-Dick Test Pack to Order

Roll of CliniEco autoclave indicator tape with diagonal stripes for steam sterilization

How Often Must US vs Canadian Clinics Run Sterilizer Testing? Which Bowie-Dick Test Pack to Order

The first load of the day is the one a pre-vacuum sterilizer cannot get wrong. Before the autoclave is trusted with an instrument set, a Bowie-Dick pack goes in, runs, and shows whether the vacuum system actually pulled the air out of the chamber. A clinic that skips it, or runs it after the first load has already gone out, has released instruments on an assumption.

That assumption is what this guide is about, from the buying side. How often the test has to run in Canada and in the United States, which sterilizers it applies to, how many packs a year those answers imply, and what belongs on the purchase order so the test is available on the morning it is needed.

This guide is written for the practice manager, clinical lead or buyer who owns the monitoring routine in a Canadian dental office, medical clinic, long-term care home or small laboratory, and who has to reconcile a box of test packs against a year of air-removal records.

How often must a Canadian clinic run the air-removal test?

The answer starts with the unit, not the calendar. A Bowie-Dick test belongs to sterilizers that remove air with a vacuum pump before admitting steam, which covers pre-vacuum and Class B benchtop units. For those units the routine is daily: one pack, before the first load of the day, every day the sterilizer is in use.

In Canada the binding layer is provincial. Ontario's dental college standard expects a daily air-removal test on pre-vacuum sterilizers, alongside the daily biological indicator that province requires, and provincial infection prevention guidance for hospitals and clinics describes the same routine even where it does not spell out a schedule. CSA Z314:23 is the Canadian reprocessing standard that describes how a monitoring programme should be organised, and it is a standards layer a practice can point to rather than a statute. Health Canada regulates the devices and the establishment licence behind them, not the test interval.

The practical consequence is a fixed daily slot. Put the pack in the chamber before the day's first instrument load, read it at the end of the cycle, and record the result before anything is released. A pack that runs at ten in the morning has answered a question about the chamber, not about the load that already went out at nine.

A Bowie-Dick test pack specified to ISO 11140-5 Type 2, six per box is built for that daily slot: a single-use pack that simulates a full cotton load, with an irreversible pass indicator that is read once and filed.

How often does the United States require it?

The American baseline comes from ANSI/AAMI ST79, the comprehensive guide for steam sterilization in health care facilities, together with the CDC guideline that most facilities cite alongside it. Both describe an air-removal test at the beginning of each day the pre-vacuum sterilizer is used, before any load is processed, and both add occasions where a test is required regardless of the calendar.

Those occasions are worth writing into the routine:

  • After installation or relocation of the sterilizer.
  • After a major repair that touches the vacuum system, the door gasket or the steam supply.
  • After a steam supply interruption or a change of steam source.
  • After a failed pack has been investigated and corrected.

The difference between the two countries is where the obligation sits, not what the test does. Canadian practice answers to a provincial college standard and an inspection. American practice answers to a national guideline, a consensus standard and an accreditation survey. The daily rhythm happens to be the same on both sides, which is useful for a group operating in both markets, but the document a clinic cites when asked why is not.

CliniEco Bowie-Dick test pack, ISO 11140-5 Type 2, with accept and reject pass indicator

Which sterilizers need a pack, and which do not?

Matching the consumable to the machine is where first orders go wrong. A Bowie-Dick pack tests air removal, and only a machine that removes air mechanically has that failure mode to test.

Sterilizer type Air removal Bowie-Dick pack
Pre-vacuum (Class B) benchtop Vacuum pump pulls air out before steam enters Required daily before the first load
Pre-vacuum (Class B) floor or cabinet unit Vacuum pump, often multi-stage Required daily before the first load
Gravity displacement (Class N) Steam pushes air out through a drain Not the applicable test
Gravity unit with a conditioning stage Steam and gravity only Not the applicable test; monitor with chemical and biological indicators

A gravity unit still needs monitoring, just not with this consumable. The chemical indicator on each pack and the biological indicator on the day's schedule do that work, and a Class 5 steam chemical integrator, 100 per pack gives a load-level read that is more informative than the tape on the outside of a pouch.

Side by side: what differs between the two jurisdictions

Item Canada United States
Routine air-removal test Daily on pre-vacuum units, before the first load; provincial college standard is the binding document Daily on pre-vacuum units, before the first load, under ANSI/AAMI ST79
Terminology Provincial standards often say air-removal test AAMI and CDC say Bowie-Dick test
Standard layer CSA Z314:23 plus provincial standards ANSI/AAMI ST79 plus CDC guidance
Record retention Ontario expects sterilization records kept ten years Facility policy and state rules
Device regulator Health Canada, through establishment licensing FDA, through device clearance
Pack specification ISO 11140-5 Type 2 ISO 11140-5 Type 2

The terminology row is the one that costs clinics time in a search box. The same test is sold as an air-removal test, a Bowie-Dick test, a steam penetration test and a Type 2 indicator, and a buyer searching one phrase can miss a compliant product listed under another. Reading the standard number on the label settles it faster than reading the product name.

How many packs does a year of daily testing use?

The arithmetic is short, and it is the number that turns a monitoring schedule into a purchase order.

Setting Tests per year Boxes of six
One pre-vacuum sterilizer, five days a week About 250 About 42
Two pre-vacuum sterilizers, five days a week About 500 About 84
One sterilizer, four days a week About 200 About 34
One sterilizer plus retests after failures and repairs 260 to 280 44 to 47

Two lines are usually missing from a clinic's own estimate. The first is the retest: a failed pack is investigated, corrected and repeated before the sterilizer returns to routine use, and a steam supply problem can consume several packs in a week. The second is the calendar. A clinic that closes for two weeks still uses the same daily rhythm in the weeks it opens, so count working weeks rather than assuming fifty-two.

Keep four to six weeks of cover. The cost of a spare box is small next to the cost of a morning with no pack, because the alternative is releasing the first load of the day without the test that the routine depends on.

Roll of CliniEco autoclave indicator tape with diagonal stripes for steam sterilization

Which pack format and specification should the order carry?

Two attributes on the label decide whether a pack is the right one: the standard, and the cycle it was designed for.

Attribute What to look for Why it matters
Standard ISO 11140-5 Type 2 for Bowie and Dick-type air removal tests Proves the indicator is the class 2 test device, not a general chemical indicator
Indicator system series ISO 11140-3 covers class 2 indicator systems for the same steam penetration test Useful when a supplier stocks sheets rather than assembled packs
Rated cycle The 134 °C, 3.5-minute Bowie-Dick cycle on pre-vacuum units A pack rated for another cycle can fail for a reason that is not the sterilizer's fault
Pack construction Single-use pack simulating a cotton load Reproducible result day to day, no assembly by staff
Read-out Irreversible colour change, read once at end of cycle A reversible indicator can be misread on a busy morning

The pack is a consumable with a shelf life, and storage matters as much as specification. Keep boxes sealed and dry, in the temperature range on the label, and away from the decontamination sink. A pack that has absorbed moisture from a humid room is a pack whose result nobody can defend, and the failure will look like a sterilizer fault when it is a storage fault.

Alongside the packs, most clinics order the external chemical indicator used on every pouch. A sterilization indicator tape, three-roll set does that job, with the caveat that tape shows exposure rather than air removal, and a Class 4 self-sealing pouch with a dual indicator, 200 per box puts the internal and external indicator in one consumable.

What does a passing pack not prove?

A passing pack answers one question well: air was removed and steam penetrated the test load evenly during that cycle. It does not prove that every instrument in a later load reached temperature for the required time, and it is not a sterility test. Those are the jobs of the biological indicator and the physical cycle record.

That division of labour is worth explaining to new staff, because the failure modes it prevents are different. A pack catches a failing vacuum pump, a worn door gasket, a blocked drain or an air leak in the steam line. A biological indicator catches insufficient lethality, whether from a temperature shortfall, a cycle interruption or an overloaded chamber. A chemical indicator inside each pouch catches a pack that never saw adequate steam at all.

A clinic running a sterilization monitoring programme reads the three together, and files them on one record so a later question about a specific load can be answered from one sheet rather than three folders.

What should the purchase order state?

The order is a short document that decides whether the routine survives the year. It should carry:

  • The standard and type printed on the pack, not only the product name.
  • The cycle the pack is rated for, matching the sterilizer it will run in.
  • Packs per box and boxes per order, so the annual count converts cleanly.
  • The lot number and expiry date on every box received.
  • A certificate of analysis for the lot, filed with the monitoring records.
  • Storage conditions repeated for receiving staff.
  • A named reorder point, in weeks of cover rather than in boxes.

The reorder point is the line that most clinics leave out, and it is the one that prevents the failure everyone remembers: a morning with instruments waiting and no pack in the cupboard.

Where does a Canadian clinic order Bowie-Dick packs?

Order from a Canadian supplier that ships from stock and shows the standard, the rated cycle and the packs per box on the product page, so the annual figure converts into a case quantity without a phone call. Running a dental practice? See our dental sterilization and monitoring supplies for the lines a chair-side programme uses daily. A family practice or walk-in clinic with a smaller pre-vacuum unit can start from the clinic sterilization supplies page instead.

One habit is worth adopting. Buy the pack, the biological indicator and the pouch from one supplier on one account, so the monitoring record and the consumable lot can be traced together when an inspector asks which lot was in the chamber on a given morning.

References

  1. ISO 11140-5:2007 — Chemical indicators, Part 5: Class 2 indicators for Bowie and Dick-type air removal tests (checked 24 October 2026)
  2. ISO 11140-3:2007 — Chemical indicators, Part 3: Class 2 indicator systems for use in the Bowie and Dick-type steam penetration test (checked 24 October 2026)
  3. ISO 11140-1:2014 — Chemical indicators, Part 1: general requirements (checked 24 October 2026)
  4. ISO 11138-1:2017 — Biological indicators, Part 1: general requirements (checked 24 October 2026)
  5. ISO 11138-3:2017 — Biological indicators, Part 3: indicators for moist heat sterilization processes (checked 24 October 2026)
  6. ISO 17665-1:2006 — Moist heat sterilization, Part 1: requirements for development, validation and routine control (checked 24 October 2026)
  7. ISO 11607-1:2019 — Packaging for terminally sterilized medical devices, Part 1 (checked 24 October 2026)
  8. ISO 15882:2008 — Chemical indicators, guidance for selection, use and interpretation of results (checked 24 October 2026)
  9. ISO 11737-1:2018 — Microbiological methods, Part 1: determination of a population of microorganisms on products (checked 24 October 2026)
  10. ISO 14971:2019 — Medical devices, application of risk management to medical devices (checked 24 October 2026)
  11. ISO 13485:2016 — Medical devices, quality management systems, requirements for regulatory purposes (checked 24 October 2026)
  12. ISO 15223-1:2021 — Medical devices, symbols to be used with information supplied by the manufacturer (checked 24 October 2026)
  13. ISO 15190:2020 — Medical laboratories, requirements for safety (checked 24 October 2026)
  14. ANSI/AAMI ST79:2017/(R)2022 — Comprehensive guide to steam sterilization and sterility assurance in health care facilities (checked 24 October 2026)
  15. Infection Prevention and Control (RCDSO) (checked 24 October 2026)
  16. Infection Prevention and Control (Public Health Ontario) (checked 24 October 2026)

Print the sheet before the inspector asks: the compliance log center carries the printable sterilization and air-removal logs that record the pack lot, the pass result and the release decision.

Work out the yearly pack count with the sterilization usage calculator, run the sterilization self-check before an inspection, or ask a compliance specialist to review the air-removal routine. Ordering for a clinic, lab or care home? Wholesale and multi-site ordering covers case pricing and account setup, and the B2B wholesale collection lists the lines held for institutional buyers. Reselling? become a distributor.

Not sure how this applies to your own setup? Ask a sterilization compliance specialist — you’ll get a written answer specific to your equipment and province, with the regulation or standard cited.

Related Reading

Frequently Asked Questions

How often must a clinic run a Bowie-Dick test in Canada?

Every day the pre-vacuum sterilizer is used, before the first load of the day. Ontario's dental college standard expects a daily air-removal test on pre-vacuum units, and the same daily rhythm is described in provincial infection prevention guidance for hospitals and clinics. The test is not a weekly or per-load task on a pre-vacuum unit, and a clinic that runs it after the first load has already released that load without the check.

How often does the United States require a Bowie-Dick test?

ANSI/AAMI ST79 expects an air-removal test at the start of each day the pre-vacuum sterilizer is used, before any load is processed, and again after a repair that could affect the vacuum or steam supply. Facilities also run one after a new installation or a change of steam source. State rules and accreditation surveys tend to repeat that daily figure rather than relax it.

Which sterilizers need a Bowie-Dick test at all?

Only units that pull a vacuum before the steam cycle. A pre-vacuum or Class B benchtop sterilizer removes air mechanically, and the pack proves the pump and valve system did it. A gravity displacement unit drains air by steam flow instead, so the pack is not the right test for it and its monitoring looks different. Buying packs for a gravity unit is a common and expensive first-order mistake.

How many Bowie-Dick packs does one sterilizer use in a year?

One unit tested five days a week for fifty weeks needs about 250 packs. A six-pack box therefore covers roughly a week and a half of use, and a year runs to about forty-two boxes. Two pre-vacuum units double that figure. Add the retests that follow a failure, a repair or a steam supply problem, and keep a month of cover so a backorder cannot leave the first load of a day untested.

What does a passing Bowie-Dick pack actually prove?

It shows that air was removed and steam penetrated the pack evenly during that cycle. It does not prove that the load reached the required temperature for the required time at every point, and it is not a sterility test. A biological indicator answers the lethality question and a chemical indicator inside each pack answers the exposure question. The three monitor different failures, which is why the air-removal test does not replace the biological indicator.

Which standard should the pack be rated to?

The pack is a class 2 chemical indicator for the Bowie and Dick-type air removal test, specified in ISO 11140-5, and the wider series part 3 covers class 2 indicator systems for the same steam penetration test. Ask for the standard and the type on the label, and check that the pack is rated for the cycle your sterilizer runs. A pack built for a different cycle length may pass or fail for the wrong reason.

What should the purchase order state for Bowie-Dick packs?

State the standard and type, the cycle the pack is rated for, the packs per box, and the number of boxes. Require the lot number and expiry date on every box, storage in a dry place at the temperature on the label, and a certificate of analysis kept with the records. Write the pack lot into the air-removal log the same day, because a failed pack is traced by lot.

Where can a Canadian clinic order Bowie-Dick packs in case quantities?

Order from a Canadian supplier that ships from stock, shows the standard and cycle rating on the product page, and lists the packs per box so the annual count converts into a case quantity. Keep four to six weeks of cover, confirm that the packs are stored dry in receiving, and pair the order with the biological indicator and packaging lines the same sterilizer uses.

Last updated: October 2026. CliniEco Medical is a licensed medical device establishment (MDEL #35334).

Already working with clinics? Become a regional representative.