Autoclave Class B vs Class N in a Canadian Dental Clinic: What the Cycle Log Must Show

CliniEco 24-Hour Biological Indicator Incubator, precision dry-block, on a reprocessing bench

Autoclave Class B vs Class N in a Canadian Dental Clinic: What the Cycle Log Must Show

A Class N cycle has no vacuum stage and is limited to unwrapped solid instruments; a Class B cycle adds fractionated pre-vacuum and post-vacuum so wrapped, hollow and porous loads can be processed. The cycle log must show which of the two ran, because the load that can be released depends on it.

The record is only as strong as the steps in front of the chamber, and the CliniEco Dental Ultrasonic Cleaner — 6 L Benchtop, CS6.2 Dual-Frequency 32/48kHz at $699.00 is where most clinics start documenting a load.

What actually separates a Class B cycle from a Class N cycle?

Property Class N Class B
Vacuum stage none — gravity displacement only fractionated pre-vacuum, then post-vacuum drying
Loads the class is defined for unwrapped solid instruments wrapped, hollow and porous loads
Typical dental load loose hand instruments run bare cassettes, pouches, handpieces, hollow items
Air removal to record no vacuum phase to log vacuum phase and the programme used
Air-removal test relevance not applicable to a gravity cycle relevant to pre-vacuum performance
Log essentials programme, temperature, time, indicator programme, temperature, time, vacuum phase, indicator

The class labels are defined in EN 13060, the standard for small steam sterilizers, and the Canadian equivalents sit in CAN/CSA-Z314, where a clinic's written procedure should point. ISO 17665:2024 covers moist heat sterilization and is the current edition — a procedure that still cites 17665-1:2006 is quoting a withdrawn part.

Which loads can a Class N unit process in a dental clinic?

Unwrapped solid instruments, and nothing that holds air. A Class N cycle relies on gravity to push air out, so any load with a lumen, a hinge cavity or a sealed pouch keeps an air pocket steam does not displace. A pouch run in a Class N unit can come out with an indicator that changed and a pack that was not sterilized through.

The class decision is therefore a packaging decision. A clinic that processes everything in pouches or cassettes has already chosen Class B; a clinic that runs only loose solid items bare can work with Class N, provided its written procedure says so and the log reflects unwrapped loads.

What must every cycle log entry show, whatever the class?

CliniEco Constant-Heat Pouch Sealer producing a 12 mm seal on a paper-film sterilization pouch

Six things, in every entry. The date and sterilizer identifier, so a failure traces to one machine. The programme actually selected, not the one usually selected. The load contents and packaging, which is what ties the class to the release decision. The temperature and exposure time reached. The chemical indicator result. And the operator, with the biological indicator result and lot where one applies.

Canadian guidance is consistent on the shape of that record: Public Health Ontario's reprocessing material treats the record as part of the cycle rather than an audit extra, and the Ontario college standard expects monitoring results retained with the load they cover. What varies is whether the log is paper or electronic; what cannot vary is that the fields are filled at the time of the cycle.

What does a Class B cycle add to the log that a Class N cycle does not?

Two fields. The vacuum phase: a Class B programme includes air removal and drying, and a record carrying only temperature and time cannot distinguish a completed vacuum cycle from one interrupted before that stage finished. The packaging description: the log is the only place that states what was in the chamber.

A Class N entry is shorter by design: no vacuum stage to record, so the programme, temperature, time and indicator result carry the entry, and the load description reads as unwrapped solid instruments. Where one machine runs both classes, both formats sit in the same log under different programme numbers.

Does the class change how often biological indicators are run?

No. The frequency comes from the college and public health requirements that apply to the practice, not from the class label on the unit. In Ontario that means a biological indicator test on each sterilizer for each day it is used, whichever class the cycle happens to be.

What the class changes is the scope of the release each test covers. A biological indicator result releases the loads processed in that sterilizer that day, and where those loads include wrapped and hollow items, they exist as a category only because the unit is Class B. Reading the result against the load description is what an inspector does.

CliniEco 24-Hour Biological Indicator Incubator, precision dry-block, on a reprocessing bench

What does an inspector look for that logs usually miss?

Missing entries on busy days, and entries that describe a load nobody can identify — both from filling the log at the end of the session rather than at the cycle. The third recurring gap is the failed cycle: a load reprocessed after a chemical indicator did not change should keep the failed entry with the reason beside it, visible rather than overwritten.

The last gap is the class itself. A log that records "autoclave" without the programme type cannot show whether a wrapped load ran on a cycle that removes air.

Which reprocessing steps in front of the autoclave does the log depend on?

Cleaning, sealing and monitoring each leave a fact that the cycle record inherits. Cleaning decides what enters the chamber, and the 6 L unit named above takes a full cassette in one cycle, so a batch record matches a real batch.

Sealing decides whether the pack stayed sterile to the point of use, and a constant-heat sealer gives the record a seal width to quote: the CliniEco Constant-Heat Pouch Sealer — 200°C, 12mm Seal, 110V (Dental Sterilization) is $349.00. Monitoring is the third: the CliniEco 24-Hour Biological Indicator Incubator — Precision-Dry-Block, 24 Wells at $379.00 holds the 56–60 °C band a 24-hour spore test needs, with an LCD readout to copy into the record.

Which class should a Canadian dental clinic buy?

Class B, for any practice that packages instruments. Not because it sterilizes better in the abstract, but because a dental load is almost always wrapped, hollow or both, and only a vacuum cycle is defined for those loads. A Class N unit run with pouches produces records for loads the cycle was never specified to process.

Where a clinic holds both, the log keeps them apart, so the purchase decision should cover how the programme list is named on the machine: "121 wrapped" and "134 wrapped" produce different records, selected at the panel rather than written in afterwards.

CliniEco Medical distributes these products under MDEL #35334.

References

  1. EN 13060:2014+A1:2018 Small steam sterilizers (checked 1 November 2026)
  2. ISO 17665:2024 Sterilization of health care products — Moist heat (checked 1 November 2026)
  3. RCDSO — Infection Prevention and Control in the Dental Office, Standard of Practice (checked 1 November 2026)
  4. Reprocessing — Public Health Ontario (checked 1 November 2026)

Not sure which monitoring consumable fits your cycles? Request 5 free biological indicators (24-hour BI, for clinics, labs and LTC), or request a quote for volume pricing. Reselling? become a distributor.

Related Reading

Frequently Asked Questions

Is a Class N autoclave enough for a dental clinic?

Only for unwrapped solid instruments. Once instruments are pouched, wrapped or hollow, the class definition no longer covers the load, so a clinic that packages everything needs a Class B unit.

Does a Class B cycle need different monitoring from a Class N cycle?

The monitoring cycle stays the same in kind — chemical indicator on the pack, biological indicator on the schedule the college sets — but the load released depends on the class, so the log must identify which cycle type ran.

Can a Class B autoclave run an unwrapped solid load like a Class N unit?

Yes. A wrapped-goods cycle can process unwrapped solid instruments, which is why many clinics run both cycle types on one Class B unit, recording each under its own programme number.

What has to be written down if a load is reprocessed after a failure?

The failed record stays in the log, with the reason and the reprocessing entry linked to it. Overwriting the failed entry is the most common record finding in clinic audits.

Last updated: October 2026. CliniEco Medical is a licensed medical device establishment (MDEL #35334).

Already working with clinics? Become a regional representative.