What Must a Hospice Do When a Biological Indicator Fails?

Three self-contained biological indicator vials with labels printed in English and French, used to monitor steam sterilization

A positive biological indicator in a hospice lands differently than it does in a hospital. There is no sterile processing manager to take the call, no second sterilizer to move the list to, and no laboratory downstairs — the vial goes into a small incubator in a utility room and the person who reads it may also be the person who signed the load out. The result still means the same thing: the last load may not be sterile, and the instruments in it were used on people whose skin and mucous membranes are already compromised.

This page sets out what the result proves, the order the Canadian provincial guidance puts the response in, which loads are held, how the repeat test works, and where the Canadian and American positions differ. The consumables that make the response same-day rather than same-week are the 24-hour self-contained biological indicator, the dry-block incubator that reads it in house, and the Class 5 steam chemical integrator that goes inside the process challenge device.

Quick facts on a failed biological indicator in a hospice

  • The sterilizer comes out of service first, and it stays out while the repeat test runs.
  • The review covers every load since the last negative result, not just the load that produced the failure.
  • The repeat test uses the same cycle that produced the failure, not a faster one that is easier to pass.
  • Overloading, inadequate package separation and incorrect packaging are named as causes when there is no mechanical fault.
  • A second positive result turns a laboratory event into a sterilizer investigation with the manufacturer.
  • Records retained for ten years are the reason a hospice can answer a question about a load two years later.

What does a positive biological indicator actually prove?

A biological indicator carries a defined population of spores with a known resistance to the process it tests. For steam that organism is Geobacillus stearothermophilus. The vial sits inside a process challenge device so the spores are behind the same barrier the packaged instruments present, and after the cycle it is incubated. Growth means the process did not deliver the lethality it was supposed to deliver to that challenge, and the load it accompanied cannot be assumed sterile.

Three monitors answer three different questions, and confusing them is what makes a hospice's first hour worse than it needs to be. The biological indicator answers whether the process killed a resistant organism. The chemical indicator answers whether the package saw the conditions. The physical record answers what the machine actually did. A negative biological with a failed chemical indicator is a packaging problem. A negative chemical indicator with a positive biological is a machine or process problem. Reading all three before deciding is the difference between a repeat test and a service call.

Result pattern What it usually points to First action
Biological positive, chemical passed, physical normal Challenge placement, load configuration or indicator handling Sterilizer out of service, repeat in the same cycle, review the load build
Biological positive, chemical failed Process not delivered to the package at all Sterilizer out of service, engineering check before any repeat
Biological negative, chemical failed Package or indicator problem, not necessarily a process failure Hold the pack, investigate packaging and storage
Biological positive on repeat, same cycle Mechanical or cycle fault Manufacturer service, requalification before return to use

What is the order of the response in Canadian guidance?

The sequence is short and the provincial standard puts the sterilizer out of service before anything else happens: it is removed from use, the loads are held, and the repeat test is run while it stays out. Notification follows the facility's chain, and in a hospice that chain includes the unit's medical director or nurse lead rather than a laboratory supervisor, because the decision about patients is theirs.

Step What happens Who owns it in a hospice
1 Sterilizer out of service, tagged, cycle not restarted Whoever reads the result
2 All loads since the last negative result quarantined Nurse lead or charge nurse
3 Repeat test in the same cycle with a new indicator Trained operator
4 Review of load configuration, packaging and chamber loading Operator with the procedure in hand
5 Second positive: manufacturer service and requalification Facility manager
6 Written investigation, release decision, record retained Nurse lead with the file

Which loads have to be held, and for how long?

Every load processed since the last documented negative biological indicator, because the failure tells you the sterilizer may have been delivering less than it should for longer than one cycle. In a hospice that runs one load a day, that interval is usually a week; in a hospice that runs three loads a day it can be twenty. The held loads are not automatically reprocessed: the decision is whether the load was released before the result was known, and if it was, who received the instruments.

This is where the release rule matters. The provincial standard says items should not be released until the biological result is available, and allows a documented alternative for routine loads where quarantine is impractical: evaluation of a Class 5 or Class 6 chemical indicator together with the cycle's physical parameters. Implantable devices do not get that alternative. A hospice that releases on a Class 5 integrator and the printout is inside the standard; a hospice that releases because the morning list is waiting is not, and the difference is the only thing the investigation will actually turn on.

Three self-contained biological indicator vials with labels printed in English and French, used to monitor steam sterilization

How do Canada and the United States differ on monitoring frequency?

They differ on the floor, not on the principle. Canadian provincial guidance asks for a biological indicator on each day the sterilizer is used and with each type of cycle used that day. American national guidance describes at least weekly monitoring as the floor and daily monitoring as giving earlier detection on a heavily used unit. A hospice running one load every second day ends up in roughly the same place under either rule; a hospice running five loads a day does not.

Item Canada (Ontario guidance) United States (CDC guidance)
Biological monitoring frequency Each day the sterilizer is used, each cycle type used that day At least weekly, with daily recommended for heavily used units
Air removal test Every day a dynamic air removal unit is used, Class 2 indicator Recommended each day the sterilizer is used
Release before the result Class 5 or Class 6 plus physical parameters, where documented; implants excluded Load release rules set by policy and accreditation, implants quarantined
Repeat after a positive Same cycle, sterilizer out of service, review of loads since last negative Same expectations in practice, written in facility policy
Hospice oversight Provincial health authority and accreditation 42 CFR 418.60 infection control condition of participation

Do Canada and the United States differ on who is told? The American hospice condition of participation at 42 CFR 418.60 requires an agency-wide infection control programme with surveillance, investigation and education, which is the hook a US surveyor uses to ask for the investigation file. In Canada the same file is asked for by a provincial inspector or an accreditor, and the content they expect is the same: what happened, what was held, what was tested, and what was decided.

What does the repeat test have to look like?

The same cycle that produced the failure, with a fresh indicator from the same lot and a fresh process challenge device, in a chamber loaded the way the failing load was loaded. Running an easier cycle to get a pass converts a process question into a false negative, and an inspector who sees the cycling history will see it. Where the failing load was built to the chamber's limit, the repeat belongs at that limit rather than in an empty chamber, because an empty chamber passing tells you the machine works and not that the process does.

Three consecutive negatives are the usual basis for returning a unit to service when the cause was corrected, and a second positive is the point at which the hospice stops investigating and calls the manufacturer. The service visit ends with a requalification that follows the installation logic, not with a repaired part and a shrug.

How do Canada and the United States differ on documenting a failed load?

Six items: the date and time the result was read, the load or loads affected, the immediate action, the repeat result with its cycle, the investigation findings including the load configuration and any mechanical fault, and the release decision with the name behind it. The record is what separates an event that was managed from an event that happened.

Retention is usually borrowed from the clinical record rules that apply to the setting. The provincial standard asks for records to be kept according to facility policy, and the reference most clinical settings use in Ontario is Ontario Regulation 114/94, which sets a ten-year retention period for clinical records. A sterilizer log kept for two years cannot answer the question that gets asked two years later.

The American hospice documents the same six items, and the file is requested differently. The condition of participation at 42 CFR 418.60 requires an agency-wide infection control programme with surveillance and investigation, which is what a surveyor asks the investigation note to demonstrate, and retention follows the facility's HIPAA policy at 45 CFR 164.316. In Canada the same file is read by a provincial inspector or an accreditor against the provincial standard.

A dry-block incubator with numbered wells holding biological indicator vials at incubation temperature

What is different about a failure in a ten-bed hospice?

Three things, and none of them is regulatory. There is usually one sterilizer, so the held loads are the whole service and the practical question becomes where the instruments for the next two days come from — a neighbouring site, a contracted service or single-use alternatives. There is usually one incubator, so the repeat competes with the routine test for the same wells and the same 24 hours. And there is usually no one whose only job is this, so the investigation is written by someone who is also covering a shift.

The three practices that make it work are unglamorous. A pre-agreed fallback for instruments, named in the procedure before it is needed. A second incubator or a documented plan for reading the repeat alongside the routine test. And a one-page investigation template that asks the six questions so the person filling it in at 23:00 is not inventing structure. A hospice that has those three in place experiences a positive indicator as a bad day rather than a crisis.

Where does a hospice take this next?

Three things a hospice can act on rather than read: a printable compliance log sheet that records the load, the indicator lot, the result and the release signature and exports from the browser; the sterilization log generator on the same page, which assembles the month's records from the cycle schedule; and, where an investigation has to be documented for an inspector or an accreditor, Ask a Compliance Specialist, which returns a written answer citing the standard it rests on.

Hospices ordering indicators, integrators and incubators across several sites can ask about the institutional account enquiry page for case quantities and account setup. Reselling? become a distributor.

Related reading

Sources and version notes

Frequently Asked Questions

Does the sterilizer have to come out of service immediately?

Yes. It is removed from use before the repeat test is run and it stays out until the repeat result and the investigation support a return to service. Continuing to process loads while a positive result is being investigated removes the ability to bound the event.

Which loads are affected by one positive result?

Every load processed since the last documented negative biological indicator. The failure does not prove that only the accompanying load was affected, and the review has to cover the interval rather than the single cycle.

Can the repeat test use a different cycle?

No. The repeat uses the same cycle that produced the failure, with a fresh indicator and the same load configuration where the load was the issue, because a different cycle tests a different process.

How many negatives are needed to return the unit to service?

Three consecutive negatives after the cause has been corrected is the usual basis, and any second positive result moves the case to manufacturer service and requalification rather than to another repeat.

Does a hospice need its own incubator?

Not necessarily, but it needs a documented route from the vial to a controlled incubation temperature and a result that is read and recorded. Sending vials to a hospital laboratory the next morning turns a same-day decision into a next-day one, which changes the release rule for the loads in between.

What happens to the patients whose instruments were in a held load?

The investigation establishes whether the load was released before the result and who received the instruments. Where release happened, the clinical lead decides on exposure assessment and disclosure, and the decision is written down rather than made in a corridor.

Regulations and standards are cited as published at the time of writing and are not reproduced in full. Provincial requirements differ and are revised, so confirm the version in force for your setting. This article is for information and is not legal advice. CliniEco Medical distributes medical consumables under MDEL #35334.

Vous travaillez déjà avec des cliniques ? Devenez représentant régional.