An infection control audit of a dental office rarely begins with a question about which autoclave the practice owns. It begins with a folder, a log book and a walk through one room. The auditor is asking whether the office can show the same thing three ways: that a written procedure exists, that the procedure was followed on a specific day, and that the follow-up happened when something failed. Instrument reprocessing is where those three answers either line up or fall apart.
This page sets out what an auditor asks for in a Canadian dental office, how the evidence chain is built from packaging and indicators through to the log book, and where the Canadian expectation parts company with what a United States surveyor asks. The consumables that carry most of the evidence are simple ones: a Class 4 self-sealing sterilization pouch with a writable face, and a 24-hour self-contained biological indicator for the loads that need a result before release.
Quick facts on the reprocessing evidence chain
- Each instrument package must carry a Type 1 chemical indicator on the outside and a Type 4, 5 or 6 indicator inside, per the Ontario college standard.
- Every package is labelled with the date of reprocessing, the sterilizer used, the cycle or load number and the initials of the person who did the work.
- The sterilizer log book, like other office records, is kept for at least ten years from the date of the last entry.
- Ultrasonic cleaning solutions are changed each day or sooner if visibly soiled, and cleaning brushes are sterilized or discarded at the end of every day.
- On a pre-vacuum sterilizer, an air removal test is run at the beginning of each day the sterilizer is used, with the test pack in an empty chamber.
- A positive biological indicator takes the sterilizer out of service until a repeat result is negative and the cause is identified.
What does an auditor ask to see first?
The written procedure. A dental office is expected to hold an office manual that includes infection prevention and control policies, the manufacturer's instructions for the equipment it owns, and the procedures staff actually follow. The audit question is whether the manual describes the room that exists. A procedure copied from another practice that mentions two sinks in a unit that has one is the kind of mismatch that turns a routine review into a written order.
From there the auditor works outward in the order instruments travel: receiving and cleaning, rinsing and drying, preparation and packaging, sterilization, storage. Each stage has an artefact. Cleaning has a change log for the ultrasonic bath and a note on when the brushes were last replaced. Packaging has the pouch, the internal indicator and the label. Sterilization has the cycle record and the biological result. Storage has a closed cabinet and a shelf that is not under a sink.
| Stage | What the auditor reads | Common gap |
|---|---|---|
| Cleaning | Solution change record, ultrasonic efficacy check, brush replacement | Bath solution topped up rather than changed |
| Rinsing and drying | Water quality, drying before packaging | Packs assembled while still wet |
| Packaging | Type 1 outside, Type 4, 5 or 6 inside, single layer, hinged instruments open | Internal indicator missing from some packages |
| Sterilization | Cycle parameters per load, air removal test, biological result | Parameters recorded as a range, not as read |
| Storage | Closed, clean, dry, not under a sink or beside it | Sterile stock stored on the dirty side |
Which indicator goes where in a package?
The layering is not optional and it is not redundant. The external Type 1 indicator shows that the package went through a cycle, which lets staff sort processed from unprocessed trays. The internal Type 4, 5 or 6 indicator shows that the conditions inside the package were reached, which is a different claim. Some pouches carry the external indicator as part of the film, so the office buys one item instead of two; the internal indicator is still a separate decision, and it is the one most often dropped when a busy week runs the stock down.
A process challenge device handles the third question: whether the load as a whole was sterilized. The device can be commercial or built in house from the package in the load that is hardest to sterilize — a heavy multi-instrument tray, or a set mixing metal and plastic — labelled as the test pack and placed in the position the sterilizer manufacturer identifies as least favourable. The result is checked at the end of the cycle, before the load is released.
What does the auditor read in the log book?
The log is the memory of the unit, and it is read as a sequence rather than as individual entries. An auditor looks for gaps on days the office was open, for repeated entries written in one hand at one time, and for a biological result that appears without a corresponding cycle. The Ontario standard requires the log to be kept for at least ten years from the last entry, which means a practice that changes sterilizers keeps the old book rather than clearing the shelf.
Daily operation of every sterilizer is reviewed and documented, malfunctions are noted with the action taken, and physical parameters are recorded for each load. Where the sterilizer prints or stores parameters, the printout becomes part of the same record. Where it does not, the office writes the values down, and the standard adds that replacing a unit without a recording device should be considered in a reasonable time rather than treated as an emergency.
How does Canada differ from the United States on audit evidence?
The two systems ask for the same physical acts and differ on who owns the paper. In Canada, provincial dental regulators publish standards that an inspector can quote, and the federal device rules govern what the manufacturer must tell the office about processing. In the United States, the CDC guidance describes the practices, OSHA enforces the bloodborne pathogens rule for worker protection, and state dental boards plus accreditation bodies set the documentation expectation. A Canadian office can point to a college clause; a United States office usually points to its own policy, which is why the policy has to be specific.
| Item | Canada | United States |
|---|---|---|
| Source of the reprocessing standard | Provincial dental regulator standard of practice, with CSA Z314 as the technical reference | CDC guidelines and facility policy, with state board rules |
| Indicator requirement | Stated as a requirement: Type 1 outside, Type 4, 5 or 6 inside | Described in guidance and adopted through policy |
| Record retention | Ten years from the last entry in the sterilizer log | Set by state rule and facility policy |
| Worker protection | Provincial occupational health and safety legislation | OSHA bloodborne pathogens standard |
| Processing instructions | Manufacturer information under ISO 17664-1:2021 | Manufacturer instructions for use, cleared with the device |
Do the two countries differ on how a failed biological test is handled?
Both treat a positive biological indicator as a stop signal for the sterilizer, and both expect the load to be recalled. The Canadian standard is unusually concrete about the sequence: remove the unit from service, review the physical and chemical records since the last negative result, repeat the test with the same cycle, and keep the unit out of service until the repeat is negative. Common causes named in the standard are overloading, inadequate package separation, and packaging material that is wrong for the cycle. In the United States the same logic sits in guidance and accreditation expectations rather than in a single clause, so the office writes the escalation itself — and an office that has never written it tends to improvise at the worst moment.
Which purchases carry the audit trail?
Four lines do most of the work. Pouches carry the label, the external indicator and the seal in one item. Internal integrators carry the in-package result. Biological indicators carry the load-level result, and the choice of read time decides whether a load waits overnight or is released the same day. Tape carries both the seal and the external indicator where the office wraps cassettes rather than pouching single sets.
An office rebuilding its evidence chain usually starts with the packaging step, because it is the one that fails quietly: a Class 5 steam chemical integrator inside each package, and sterilization indicator tape for instrument packs where wraps are used. Offices with pre-vacuum cycles also keep a Bowie-Dick test pack for the start-of-day air removal check.
What else does the walk-through cover?
Two items sit outside the sterilizer and still appear on the report. The first is the eyewash provision: a plumbed or self-contained station has to be within a ten-second walk of the reprocessing area, which the standard translates as roughly sixteen to seventeen metres. The second is hand hygiene: a dedicated hand-washing sink that is not used for instrument cleaning, or alcohol-based hand rub in the area when the plumbing does not allow a second sink.
Sharps handling is checked in the same pass. Burs are removed from handpieces immediately after the procedure, sharps are removed from trays before cleaning, and utility gloves are worn for manual cleaning of contaminated instruments. None of this is exotic, and all of it is written down in the standards the auditor is reading from.
Which records should be printable before the visit?
The load record and the count sheet are the two documents an auditor most often asks to see in paper form. Both are collected in the compliance log centre, which also carries the sterilization log generator for a unit that wants the fields laid out rather than improvised.
Have an inspection date and want the evidence chain checked? Send the unit layout, the sterilizers, the cycle types and a sample week of logs, and the answer will name the clause each gap falls under. Ask a Compliance Specialist.
Outfitting several operatories or a group of offices? The institutional account enquiry page covers case quantities and account setup. Reselling? become a distributor.
Related reading
- How many instrument sets a Quebec office needs per operatory
- What an auditor checks about instrument maintenance and cost per use
- How many biological indicators per sterilizer
- Drying instruments before packaging
- What an auditor checks on curettes and scaling tips
Sources and version notes
- RCDSO standard of practice, infection prevention and control in the dental office, version 3 — checked 14 November 2026.
- Royal College of Dental Surgeons of Ontario, infection prevention and control resources — checked 14 November 2026.
- Public Health Ontario, reprocessing of dental equipment checklist — checked 14 November 2026.
- CSA Z314:23, reprocessing of medical devices in all health care settings — checked 14 November 2026.
- Ordre des dentistes du Québec, infection prevention and control and device reprocessing guidelines — checked 14 November 2026.
- ISO 17664-1:2021, manufacturer processing information for medical devices — checked 14 November 2026.
- ISO 11140-1:2014, chemical indicators, general requirements — checked 14 November 2026.
- ISO 11140-5:2007, indicators for air removal test packs — checked 14 November 2026.
- ISO 13397-1:1995, periodontal curettes, dental scalers and excavators, general requirements — checked 14 November 2026.
- CDC, summary of infection prevention practices in dental settings — checked 14 November 2026.
- CDC, guidelines for infection control in dental health-care settings, 2003 — checked 14 November 2026.
- OSHA, bloodborne pathogens standard — checked 14 November 2026.
- Charter of the French Language, CQLR c. C-11 — checked 14 November 2026.
- Commission des normes, de l'équité, de la santé et de la sécurité du travail — checked 14 November 2026.
- ASSTSAS, sector occupational health and safety association — checked 14 November 2026.
- Institut national de santé publique du Québec — checked 14 November 2026.
- openFDA device classification database — checked 14 November 2026.
- World Health Organization, medical devices — checked 14 November 2026.
Frequently Asked Questions
Does every package need an indicator inside it?
Yes. The standard requires a Type 1 external indicator on each package and a Type 4, Type 5 or Type 6 indicator inside it. Some pouches include the external indicator in the film, but the internal indicator remains a separate item.
How long must the sterilizer log be kept in Ontario?
At least ten years from the date of the last entry in the record. The log is treated like other office administrative records, so a practice that changes sterilizers keeps the earlier book.
What happens if a biological indicator turns positive?
The sterilizer comes out of service, the physical and chemical records since the last negative result are reviewed, and the test is repeated with the same cycle. The unit stays out of service until the repeat result is negative.
Is an air removal test required every day?
For pre-vacuum sterilizers, an air removal test is run at the beginning of each day the sterilizer is used, with the test pack placed in the chamber of an empty sterilizer per the manufacturer's instructions.
Can an office test its own biological indicators in house?
Yes. In Quebec the guidelines note that with laboratory verification services closing, offices may carry out the verification themselves, and recommend acquiring the equipment and keeping a register of results. Ontario expects the result to be recorded in the log.
Does packaging have to be a pouch?
No. Wrapped perforated cassettes, peel pouches and woven or non-woven wraps are all acceptable, provided the material is designed for the sterilization process used and the package is not overloaded.
Provincial standards and federal guidance are cited as published at the time of writing and are not reproduced in full. This article is for information and is not legal advice. CliniEco Medical distributes medical consumables under MDEL #35334.