Quick facts
- The three devices answer three different questions: a water bath heats a container in a liquid medium, a dry block heats tubes in metal wells, and an incubator holds a stated temperature in a chamber large enough for plates or racks.
- IEC 61010-1:2010 sets the general safety requirements for electrical measuring, control and laboratory equipment; the heating-specific part, IEC 61010-2-010, is recorded by the IEC catalogue as withdrawn from 12 February 2019 in its 2014 edition (EVS catalogue entry, read 2026-10-20) — a spec sheet that quotes the 2014 edition is quoting a superseded document.
- ISO 15189:2022 sets quality and competence requirements for medical laboratories, and equipment control sits inside it; ISO/IEC 17025:2017 does the same job for testing and calibration laboratories.
- A dry block holds vials at a set temperature with no water and no spills, which is why self-contained biological indicators are incubated in one: the 24-hour readout runs at 56-60 °C per the product documentation read on 2026-10-20.
- The DLAB HB120-S dry block in this catalogue is listed as cTUVus certified and tested to UL 61010-1 and CAN/CSA-C22.2 No. 61010-1 (product page read 2026-10-20) — the Canadian and US electrical safety standards, on one certificate.
- Pages were read on 2026-10-20; the IEC and ISO catalogue entries, the openFDA API and the product pages returned 200.
A laboratory that needs to hold something at a temperature has three common ways to do it, and the choice is usually made by habit rather than by specification: the water bath that was already in the room, the dry block that came with the spore test kit, or an incubator bought for something else. The three differ in what they heat, how evenly, what they consume and how much space they need — and those five columns are the whole purchase decision. This article compares them on use, specification, consumables, maintenance cycle and scale, and it flags the one document question that catches buyers: which edition of the electrical safety standard the unit was actually tested to. The dry block side of the comparison is represented in this catalogue by the DLAB HB120-S LED digital dry bath, a 110-120 V unit with a North American plug.
What does each device actually heat?
A water bath heats a container through water. The water is the heat-transfer medium, so the container sits in it, the water circulates by convection or by a stirrer, and the temperature the sample sees depends on the water level, the fill, the lid and the position in the bath. Water baths are used for thawing, for incubations at body temperature, for warming reagents and for any step where a large, stable, gently heated volume is wanted.
A dry block heats tubes through machined metal wells. There is no water, so there is no spill, no evaporation and no biocide; the tube sits in a well whose diameter matches it, and the contact between tube wall and block is what transfers the heat. The consequence is that block fit matters as much as set-point accuracy: a tube that is a loose fit in a well is a tube that lags the block.
An incubator heats a chamber. It holds a stated temperature in a volume large enough for Petri dishes, racks or flasks, usually with forced air circulation and sometimes with CO2. It is the device for work that needs days rather than hours, and for work where the load is a stack of plates rather than a rack of tubes.
Which device fits which job?
| Device | Use | Specification to pin down | Consumables | Maintenance cycle | Scale it suits |
|---|---|---|---|---|---|
| Water bath | Thawing, warming reagents, long low-temperature holds, large containers | Temperature range and uniformity, bath volume, lid, stirrer, low-level cut-out | Water, biocide or algaecide, cleaning agent, thermometer for checks | Weekly water change and clean; periodic temperature verification against a reference | Benches with bulky containers and a small number of steady protocols |
| Dry block | Tube heating, enzyme reactions, incubating self-contained biological indicators at 56-60 °C | Block format and well count, temperature range and stability, lid, calibration access | Interchangeable blocks, vial adaptors, calibration probe | Block cleaning, well inspection, periodic temperature verification at the working set-point | Small footprints with tube-based work and no water services |
| Incubator | Plates, racks, flasks, culture work over days, CO2 work if specified | Chamber volume, uniformity and recovery time, shelves, door type, CO2 control if needed | Shelves, plate stacks, gas if CO2, cleaning agent | Chamber clean and decontaminate on a schedule, filter and fan check, temperature mapping | Larger volumes and multi-day work where a chamber is the only workable format |
Why does the standard edition on the spec sheet matter?
Laboratory heating equipment is covered by IEC 61010-1 for general safety and by IEC 61010-2-010 for the heating function. The IEC catalogue record for the 2014 edition of IEC 61010-2-010 shows it as withdrawn from 12 February 2019 — which means a supplier quoting "IEC 61010-2-010:2014" on a current data sheet is quoting an edition that the standards body has already replaced.
That is not a reason to reject a device. It is a reason to ask a second question: which edition was the unit tested to, and does the certificate name the edition? A certificate that names the standard without a year is a certificate that cannot be checked, and a device bought for a licensed laboratory will eventually be asked about by an assessor.
The same logic applies to the Canadian and US marks. The DLAB dry block in this catalogue is listed as cTUVus certified and tested to UL 61010-1 and CAN/CSA-C22.2 No. 61010-1, which is the pair that matters for a unit plugged into a Canadian wall and, if resold, into a US one.
What does each device cost to run, beyond the purchase price?
The water bath is the lowest-cost to buy and the most expensive to keep honest. It consumes water, it grows things if it is not cleaned, and it needs a biocide routine that somebody has to own. A bath that is topped up rather than changed is a bath with a biofilm and a drifting temperature, and both problems are invisible until a result is questioned.
The dry block consumes almost nothing: no water, no biocide, no drain. Its running cost is the periodic temperature verification and the occasional block replacement when wells corrode or a tube seizes. For a clinic doing a handful of tube-based tests a day, that is the lowest total cost of the three.
The incubator is the most expensive to buy and to qualify, because a chamber has to be mapped rather than spot-checked: several positions, loaded and unloaded, with recovery time recorded. Below a certain throughput, a chamber is a large device doing a small job.
Temperature devices: Canada and the United States
| Item | Canada | United States |
|---|---|---|
| Electrical safety | CSA C22.2 No. 61010-1, often on a cTUVus or CSA mark | UL 61010-1 |
| Laboratory oversight | Provincial licensing and accreditation, for example IQMH in Ontario | CLIA for clinical testing, plus voluntary accreditation |
| Quality standard for the lab | ISO 15189:2022, or ISO/IEC 17025:2017 for testing labs | ISO 15189 or ISO/IEC 17025, adopted voluntarily |
| Device classification | Class assigned by the manufacturer under SOR/98-282 when the unit is a medical device | FDA classification where applicable; general lab heating equipment is not classified as a device |
| Temperature record | Equipment log with set-point, reading and action | Equipment log with set-point, reading and action |
What has to be recorded for each device?
For all three, the record has the same spine: identity of the unit, set-point, actual reading, date, who read it and what was done if the reading was outside limits. A water bath adds the water change date and the biocide addition; a dry block adds the block format in use and the verification set-point; an incubator adds the position used for the check and, where relevant, the CO2 reading.
What separates a defensible record from a ritual is the action column. A log that shows a reading of 55.2 °C against a 56-60 °C requirement with no comment is a log that recorded a failure and ignored it. The action can be short — "re-checked after 30 minutes, 56.4 °C, vial moved to centre well" — but it has to exist.
Keep the verification separate from the daily check. The daily check proves the device is in the expected range today; the periodic verification against a reference thermometer proves the display still means what it says. Conflating the two is how a device with a drifting sensor passes a year of daily ticks.
How should a lab choose between them?
Start with the container. If the work is done in tubes, a dry block is the natural fit and the block format is the specification to get right. If the work is done in flasks, bottles or bags, a water bath is the format that accepts them. If the work is done on plates or over days, the chamber is the only one of the three that will do it.
Then look at the room. A water bath needs a water supply, a drain path and a bench that tolerates splashes; a dry block needs a socket and a level bench; an incubator needs floor or bench space, ventilation and a door swing. A device that does not fit the room is used badly.
Then look at the record the lab already keeps: a lab running ISO 15189 already has an equipment register and a calibration schedule, and adding a device means adding a line to both.
Where do the consumables fit?
Each device pulls a different consumable line. A water bath consumes water treatment, biocide and cleaning agent, and it usually shares a bench with a thermometer that has its own calibration. A dry block consumes blocks and vial adaptors, and it is the device that makes a self-contained biological indicator usable without a water bath — which is why the two are often bought together.
An incubator consumes shelves, plate stacks and, where CO2 is used, gas and tubing. In a clinic lab the consumable that matters most is often the tube or plate that goes in, and that is a stock decision made on a different schedule from the device decision.
Whichever unit a lab buys, the consumables around it are reordered on the same schedule as the calibration check. Order through the wholesale programme for case pricing and an account, or become a distributor for resale. The DLAB HB105-S2 dry bath incubator with lid sits in the same catalogue. Consumables for this line are listed under the department page.
Sources
- ISO 15189:2022, medical laboratories, requirements for quality and competence
- ISO/IEC 17025:2017, competence of testing and calibration laboratories
- IEC 61010-1:2010, safety requirements for electrical equipment for measurement, control and laboratory use
- IEC 61010-2-010:2014, particular requirements for laboratory equipment for the heating of materials (catalogue record shows withdrawal from 12 February 2019)
- ISO 11138-1:2017, biological indicators for sterilization processes
- ISO 17665-1:2006, moist heat sterilization
- DLAB HB120-S LED digital dry bath, product page (read 2026-10-20)
- openFDA, device classification API (search for incubator, read 2026-10-20)
- FDA, device classification database
- Medical Devices Regulations, SOR/98-282
- Health Canada, medical devices
- Public Health Ontario, infection prevention and control
- Institute for Quality Management in Healthcare
- Ontario, Laboratory and Specimen Collection Centre Licensing Act
- Canadian Centre for Occupational Health and Safety, OSH answers
- CSA Group, standards catalogue
Three-device comparison worksheet. One page that scores a candidate water bath, dry block and incubator against the five columns used here — use, specification, consumables, maintenance and scale — with a blank for the standard edition on the certificate. Print the temperature device worksheet — plain paper, no account and no sign-up, and the certificate line is the one buyers forget.
Equipment temperature log. A monthly sheet with a column for the device, the set-point, the reading, the action taken and the initials, sized for three devices on one page. Print the equipment temperature log and keep it at the bench rather than in the office, because the reading is taken at the bench.
Ask a compliance specialist. Whether a heating device needs to appear in a device licence, which edition of the electrical standard an assessor will ask for and how the verification interval should be justified are questions that depend on the equipment and the province. Ask a compliance specialist — written answer specific to your equipment and province, with the regulation or standard it is based on cited.
Related reading
- Laboratory water baths in Canada and the US: which rules apply
- Laboratory equipment acceptance testing in Canada and the US: which checks and records apply
- Pipette, balance and centrifuge calibration: building a defensible interval schedule
CliniEco Medical supplies eye care, laboratory and dental consumables of the kind described in this article. MDEL #35334. This article is written for laboratory managers and buyers and is not clinical advice; the equipment a laboratory uses and the temperatures its methods require are set by the laboratory director under its own quality system.
Frequently Asked Questions
Is a dry block better than a water bath?
Neither is better in general. A dry block suits tube-based work with no water services and no spill risk; a water bath suits large or awkward containers that need a liquid medium. The choice follows the container and the bench, not the brand.
Can a dry block incubate biological indicators?
Yes, and it is a common use: self-contained biological indicators are held at 56-60 °C for the 24-hour readout in a dry block with a matching well. The block format and the well fit are what make the temperature at the vial match the set-point.
Why does the edition of IEC 61010-2-010 matter?
Because the 2014 edition is recorded as withdrawn from 12 February 2019 in the IEC catalogue. A data sheet quoting that edition is quoting a superseded document, so ask which edition the certificate names.
What does cTUVus certification mean on a Canadian purchase?
It indicates testing to both the US and Canadian electrical safety standards — in this catalogue's DLAB unit, UL 61010-1 and CAN/CSA-C22.2 No. 61010-1 — which is what a unit sold on both sides of the border needs.
How often should the temperature be verified?
The interval follows the device's role and the laboratory's quality system: daily checks prove the reading today, while periodic verification against a reference thermometer proves the display is still true. Both belong in the equipment record.
Do I need to map an incubator?
A chamber should be mapped rather than spot-checked, because temperature varies by position and by load. Mapping records several positions loaded and unloaded, with recovery time, and it is the document an assessor will ask for.
Is a laboratory incubator a classified medical device?
Not under that name in the US classification database, where a search for incubator returns the neonatal devices at 21 CFR 880.5400 and 880.5410. In Canada the manufacturer assigns a class only where the unit is a medical device under SOR/98-282.