Gonioscopic Prisms in Canada vs the US: Which Class Applies?

Examination table with a fresh roll of paper dispensed across the upholstery in a clinic room

Quick facts

  • A gonioscopic prism (goniolens) is a prism placed on the anaesthetised eye to view the anterior chamber angle, usually with angled mirrors to reach the whole circumference.
  • In the United States it is a named entry. 21 CFR 886.1660, Gonioscopic prism, is Class I, product code HKS read from the openFDA classification database.
  • Canada keeps no named entry for the prism itself. A device that comes into contact with the surface of the eye is an invasive device, and Rule 2(1) of Schedule 1 places it in Class II.
  • Rule 2(3) lifts a device intended to remain in contact with the surface of the eye for at least 30 consecutive days to Class III.
  • The US entry describes a prism placed on the eye to study the anterior chamber; a maker whose stated use is surgical or diagnostic support answers the Canadian rule differently from one whose stated use is routine screening.
  • Sections, classes and product codes below were checked against the eCFR, the Regulations and the openFDA classification database on 2026-10-16.

A gonioscopic prism is the lens that lets a clinician see the angle of the eye: the patient's eye is anaesthetised, the prism is placed on the cornea with a coupling medium, and mirrors inside the glass fold the angle into view. The United States names the device and keeps every version in one class; Canada keeps no entry and classifies it by where it touches. This article sets out both routes and the handling records a contact lens leaves behind, with the perforated exam table roll that covers the examination chair.

What is a gonioscopic prism?

It is a contact optical device. The prism rests on the surface of the eye and the examiner looks through it at the trabecular meshwork, the drainage angle between the cornea and the iris. A single-mirror lens sees one part of the angle at a time, so the examiner rotates it; a four-mirror lens reaches the full circumference without rotation; a magnifying version adds optical power for finer structures. The same family includes the indirect goniolens used with a slit lamp and the direct surgical lens held by the surgeon during angle surgery.

The device is simple, which is why it is so widely used, but it is not passive in a regulatory sense. It is placed in contact with the surface of the eye. That single fact is what moves it out of the non-invasive rules in Canada and gives it a class of its own, even though the US entry for the same object sits at the lowest class the FDA uses.

Two records travel with the lens. The first is the intended-use statement the maker puts on the label, because that is what the classification rules read. The second is the handling record in the clinic: which patient it was used on, how it was cleaned between patients, and whether it was sterilised or disinfected. A contact lens that is reused across patients is a reprocessing question before it is a purchasing question.

Examination table with a fresh roll of paper dispensed across the upholstery in a clinic room

What class is a gonioscopic prism in the United States?

It is a named entry. 21 CFR 886.1660 is titled Gonioscopic prism, and the identification reads: \\"a gonioscopic prism is a device that is a prism intended to be placed on the eye to study the anterior chamber. The device may have angled mirrors to facilitate visualization of anatomical features.\\" The regulation sets Class I (general controls) for the whole description.

The openFDA device classification API returns the product code HKS against that section, and the entry is exempt from premarket notification under subpart E of part 807, subject to the limitations in section 886.9. That is the practical US position: no 510(k), general controls only, and the manufacturer keeps its own records.

Item Detail
US regulation 21 CFR 886.1660 - Gonioscopic prism
US class Class I (general controls)
Product code HKS
Stated intended use Placed on the eye to study the anterior chamber; may have angled mirrors
Premarket route Exempt from premarket notification under subpart E of part 807, subject to section 886.9
Contact with the eye The identification states the device is placed on the eye
Read on eCFR identification text and openFDA classification, both read 2026-10-16

How does Canada classify a gonioscopic prism?

Canada keeps no named entry, so the class is derived from Schedule 1 of the Medical Devices Regulations. The first question the rules ask is not what the device is called but what it does to the patient. A prism that is placed on the eye comes into contact with the surface of the eye, and Rule 2(1) reads: \\"Subject to subrules (2) to (4), all invasive devices that penetrate the body through a body orifice or that come into contact with the surface of the eye are classified as Class II.\\"

The subrules matter because they move the class in both directions. Rule 2(2) takes a device placed in the oral or nasal cavities as far as the pharynx, or in the ear canal up to the ear drum, back down to Class I - a route that does not apply here, since the eye is not a body orifice. Rule 2(3) takes a device intended to remain in the body, or in contact with the surface of the eye, for at least 30 consecutive days up to Class III. A diagnostic goniolens used and removed in a single visit does not reach that threshold; a therapeutic contact device that stays on the eye does.

The comparison that catches teams out is the direction of travel. The same object is Class I in the United States and Class II in Canada, so a clinic that reads the FDA database, sees \'Class I\' and assumes a matching Canadian entry will not find one. The correct reading is that the Canadian class is written into a rule about contact, not into a list of names.

Item Canada United States
Named entry None; classified by rule 886.1660 - Gonioscopic prism
Class Class II (Rule 2(1), contact with the surface of the eye) Class I
Governing text Schedule 1, Part 1, Rule 2(1) 21 CFR 886.1660
30-day contact Rule 2(3) lifts to Class III Not provided for in the entry
Licence route Device licence for the Class II device Exempt from premarket notification, subject to section 886.9
Product code Not applicable HKS
Rolls of paper medical tape stacked beside a single roll on a white surface

Why does contact with the surface of the eye decide the class?

Because the Canadian rules sort devices by the interface they create with the patient. A device that never touches the patient is judged on what it does; a device that enters the body, or rests on the surface of the eye, is judged on the fact that the barrier has been crossed. The eye surface rule exists because the cornea is a route into the body and because a device resting on it can carry material from one patient to the next if it is not handled properly.

That is also why the handling record is part of the classification story rather than a separate topic. ISO 17664-1:2021 sets out the information a manufacturer must supply about processing a medical device, and the reprocessing instructions for a reusable contact lens are written against the same risk the rule addresses. A clinic that buys a Class II contact device in Canada and then cleans it to a non-contact standard has a records problem even though the device itself is correct.

The US side reads differently again. Section 886.1385 covers a diagnostic contact lens made of polymethylmethacrylate and places it at Class II with the product codes HJK and NYK, so the FDA does not keep every eye-contact device in the low class - it keeps the named gonioscopic prism there and the named diagnostic contact lens one class higher. Two entries, one family, two answers, and the difference is the words the maker uses.

What should a clinic check before ordering?

Four checks. First, confirm what the label says the device is for: a prism intended to study the anterior chamber, an indirect goniolens, and a direct surgical lens are three statements and can reach three different answers under the Canadian rules. Second, confirm the contact time the maker states, because Rule 2(3) turns on whether the device stays on the eye for 30 days or more. Third, confirm the reprocessing instructions that ship with the lens, since a reusable contact device without processing information is an incomplete article under ISO 17664-1:2021. Fourth, confirm the coupling medium and the cleaning chemistry the maker supports, because a lens that is disinfected with the wrong agent is a lens that will fail its own inspection.

Check What to ask for Why it matters
Stated intended use Label text, not the catalogue heading Drives the Canadian rule that applies
Contact time Single-visit use or long-term wear Rule 2(3) lifts 30-day contact to Class III
Processing instructions Manufacturer cleaning, disinfection and sterilisation method ISO 17664-1 requires the information with the device
Coupling medium Matching gel and its compatibility A gel that damages the lens is a reprocessing failure
Optical surface Inspection method and rejection criteria Scratched optics change the reading
Records Log of use, cleaning and inspection The evidence an auditor asks for first

Practices that stock reusable eye-contact instruments usually keep them in a named instrument tray rather than loose in a drawer. The sterilisation roll for pre-cut sheets and the hypoallergenic paper tape that hold and label that tray sit in the same catalogue.

An optometry or ophthalmology practice also reorders the consumables used at the same slit-lamp bench. Clinics that stock for a whole practice can order through the wholesale programme and request a bulk quote for a standing or annual order; the perforated examination table roll sits in the same catalogue. Reselling? become a distributor.

Sources

  1. openFDA device classification API
  2. Medical Devices Regulations, SOR/98-282, full text and Schedule 1
  3. US FDA, medical device databases
  4. US FDA, overview of device regulation
  5. Health Canada, medical devices
  6. Health Canada, establishment licensing
  7. Standards Council of Canada
  8. CSA Group
  9. ISO 15004-1:2020, ophthalmic instruments, general requirements
  10. ISO 15004-2:2007, ophthalmic instruments, light hazard protection
  11. American National Standards Institute
  12. ISO 13485:2016, medical devices quality management
  13. ISO 14971:2019, application of risk management to medical devices
  14. ISO 17664-1:2021, processing of health care products
  15. Canadian Association of Optometrists
  16. College of Optometrists of Ontario, standards of practice
  17. Canadian Ophthalmological Society
  18. CCOHS, OSH answers

Printable record sheet. A goniolens log is only useful if the columns on it are the ones your process actually records. print a goniolens handling log sheet — the pack holds a use-and-reprocessing sheet, a daily equipment check and a monthly review page; it prints on plain paper, and no account and no sign-up is needed to open it

Log generator. Type your lens model, your cleaning chemistry and your province, and the page builds a dated sheet you can file straight into the quality manual. build a dated lens processing sheet — it lays out the date, the device, the method and the initials in the order an inspector reads them, and you can print as many as your log needs

Ask a compliance specialist. A classification question usually turns on how the device is used, not only on its name. Ask a compliance specialist — you get a written answer specific to your equipment and province, with the regulation or standard it is based on cited.

Related reading

CliniEco Medical supplies eye care, laboratory and dental consumables of the kind described in this article. MDEL #35334. This article is written for optometry, laboratory and dental procurement professionals and is not legal advice; the class of a device and the records a practice keeps belong to the manufacturer and to the requirements that apply to it.

Frequently Asked Questions

What class is a gonioscopic prism in the United States?

It is 21 CFR 886.1660, titled Gonioscopic prism, at Class I (general controls), with product code HKS. The entry is exempt from premarket notification under subpart E of part 807, subject to the limitations in section 886.9.

What class is a gonioscopic prism in Canada?

Canada keeps no named entry, so the class follows Schedule 1 of the Medical Devices Regulations. A prism placed on the eye comes into contact with the surface of the eye and is an invasive device classified as Class II under Rule 2(1).

Does a goniolens ever reach Class III in Canada?

Yes. Rule 2(3) lifts a device described in Rule 2(1) to Class III where it is normally intended to remain in the body, or in contact with the surface of the eye, for at least 30 consecutive days.

What else is a gonioscopic prism called?

Goniolens, gonioscopy lens, angle lens, and indirect or direct gonioscope. Trade names vary, and the regulatory question follows the intended-use statement rather than the trade name.

Are diagnostic contact lenses in the same class as a gonioscopic prism?

Not in the United States. 21 CFR 886.1660 covers the gonioscopic prism at Class I, while 21 CFR 886.1385 covers a polymethylmethacrylate diagnostic contact lens at Class II with product codes HJK and NYK.

What records should a clinic keep for a reusable eye-contact lens?

Keep the use record, the cleaning and disinfection method, the inspection result and the person who performed each step. ISO 17664-1:2021 is the standard the manufacturer's processing instructions are written against, and it is the reference an auditor will use.

Vous travaillez déjà avec des cliniques ? Devenez représentant régional.