Where to Buy Medical Specimen Transport Bags for Research Laboratories in British Columbia
Why does a British Columbia laboratory ship more paperwork than it expects?
A bench that releases forty specimens a week to a reference laboratory is not really shipping samples. It is shipping a chain of custody: a study code, a collection time, a temperature class, a requisition and a container, all of which have to arrive in the condition they left. The bag is the part of that chain nobody notices until a shipment is refused at intake.
British Columbia laboratories sit in an unusual spot. One site may run clinical work for a health authority, contract work for a biotech sponsor and internal research on the same bench, and each of those customers asks for a different level of documentation. The bag has to satisfy the strictest of them, because the bag is what the courier sees.
This guide covers what a research laboratory in British Columbia actually buys: which construction, which sizes, what the mark on the bag means, how cases are packed, and what to verify before the first shipment leaves the dock.
Where does UN3373 end and a 95 kPa claim begin?
Two claims get mixed together in supplier catalogues, and mixing them is how a laboratory ends up buying the wrong bag.
UN3373 is a shipping mark rather than a bag specification. It appears on packages that meet the Category B requirements of the transport regulations, including packing instruction P650, which sets out the triple packaging, the absorbent capacity, the pressure and drop tests, and the documents that travel with the shipment. A bag printed with the mark is claiming a role inside that package.
A 95 kPa claim is a pressure statement about the bag itself. It says the bag holds its integrity when the pressure differential reaches that figure, which matters when a specimen travels by air or in an unpressurised hold.
A third construction, the 3-wall bag, is a North American laboratory habit: an outer film, a middle absorbent layer and an inner liquid-retaining layer, with an external document pocket. It carries absorbent capacity inside the bag instead of relying on a separate pad.
None of the three is more correct than the others. What matters is that the mark on the bag, the paper in the pocket and the pack-out procedure at the bench describe the same package.
Which construction fits which sample?

| Bench output | Usual bag | Why | Check on arrival |
|---|---|---|---|
| Primary containers, one to three per bag | 3-wall, 6 x 9 in, 100 per pack | Absorbent layer built in, document pocket outside the sample zone | Pad present, closure seals, pocket not inside the bag |
| Tube racks and multi-container sets | 95 kPa, 8 x 10 in | Larger face, pressure claim printed | Mark legible, absorbent capacity stated |
| Bagged secondary sets and kits | 95 kPa, 12 x 15 in | Holds a secondary package plus paperwork | Case count is lower, plan storage |
| Small volumes at high count | 95 kPa, 6 x 9 in | Standard bench size with the claim | Batch and lot on the carton |
A laboratory that runs one bench gets away with one size. A laboratory that runs chemistry, culture and molecular work on the same site does not, and the reason is arithmetic rather than preference: the bag has to close over the requisition without folding it.
Where do specimen transport bags sit in the order?
Most British Columbia laboratories build the annual order in three blocks: containers and collection devices, transport packaging, and documentation consumables. Bags sit in the second block, and they are usually under-ordered because a bag looks reusable for longer than it is.
The 6 x 9 in 3-wall specimen transport bag, 100 per pack, is the default starting line for a bench that ships individual containers. The 95 kPa rated bag in 6 x 9 in and the 8 x 10 in format cover most of the rest, while the 12 x 15 in bag is the one that surprises buyers at storage time, because the case is physically larger than the count suggests.
Pair the order with a rigid outer container for the third layer and keep the two stored together in the pack-out area. A bag separated from its outer container by two rooms is a bag that will one day be used without one. The full range sits in the medical supply catalogue if you need to compare formats side by side.
What do the courier and the receiving laboratory ask for?
Transport paperwork is the part of the shipment a laboratory is least prepared for, because it changes with the destination rather than the sample. Three layers matter.
The first is the classification. Category A and Category B are different shipments with different packaging, and a research sample that looks ordinary can still be Category A if the pathogen is on that list. The published analysis of Category A specimen packaging in Spain is a useful reminder that the classification decision, not the box, drives everything downstream.
The second is the packing instruction. P650 sets out what the secondary package must do, including absorbent capacity sized to the total liquid volume. That is why a bag with a built-in absorbent layer is easier to defend in an audit than a bag plus a loose pad.

The third is identification. Specimen identification errors are a recognised source of laboratory harm, and CLSI PRE01 sets out process expectations for identifying patients and specimens. A bag that cannot carry an intact requisition defeats that process before the sample reaches the bench. The same logic applies to collection: CLSI GP42 covers capillary blood collection, where the container and the label travel in the same pocket.
ISO 15190 and ISO 35001 sit behind all of this as the safety and biorisk management frameworks a laboratory is audited against, and ISO 15189 explains how the receiving laboratory's own quality system will judge what arrives. The Provincial test information index is a useful public example of how much specimen-specific instruction a receiving laboratory publishes, and why the transport format has to match it.
What case formats, storage and lead times apply in British Columbia?
Case formats are where budget planning goes wrong, because price per bag and price per case point in opposite directions.
| Format | Inner pack | Case | Bench fit |
|---|---|---|---|
| 3-wall, 6 x 9 in | 100 bags | 10 packs, 1,000 bags | Single-container shipping |
| 95 kPa, 6 x 9 in | 100 bags | Multiple inner packs | High-count routine work |
| 95 kPa, 8 x 10 in | 100 bags | Lower case count | Tube racks |
| 95 kPa, 12 x 15 in | 100 bags | Lowest case count | Kits and sets |
Lead time in British Columbia is mostly a question of whether the size is stocked locally. Stocked sizes move in two to three business days; a size brought in for a contract moves in one to two weeks. Interior and northern sites add transit time in addition. Fraser Health publishes its own laboratory network information for the sites it serves, which is worth reading if your specimens move between authority sites.
Storage is the quiet failure. Bags kept flat, in the carton, away from solvent vapours and out of sunlight keep their closure performance; bags stored on a shelf beside a disinfectant bottle do not. Write the storage location into the pack-out procedure and it stops being a matter of habit.
What should you verify before the first shipment?
A short verification pass before the first shipment saves a rejected delivery later.
- The bag carries the mark the courier expects, and the mark stays legible once the bag is filled.
- Absorbent capacity is stated, and the primary containers add up to less than that figure.
- The document pocket sits outside the sample zone, so a leak cannot reach the requisition.
- The closure holds with the bag loaded to working volume, not to empty volume.
- The outer container is rigid, and the bag fits inside it without being folded.
- The receiving laboratory has agreed the format and size in writing.
- Batch and lot are recorded, so a recall can be traced.
Cost per shipment is the figure worth tracking rather than cost per bag. A lower-cost bag that forces a second outer container, or a rejected delivery, is the expensive one. The same trade-off appears in published rejection analyses: sample rejection rates are driven by collection and transport handling far more often than by the assay itself.
Working in a laboratory rather than a clinic? Our laboratory consumables and specimen handling supplies page collects the lines stocked for bench work.
Ordering for a laboratory rather than a single bench? Open a wholesale and institutional account and the size mix, case counts and documentation for a British Columbia site can be quoted together. If volumes are already known, the bulk quote form returns a case-level price without a phone call. Reselling? become a distributor.References
- IATA Dangerous Goods (HAZMAT) (checked 22 October 2026)
- Laboratory biosafety manual, 4th edition (checked 22 October 2026)
- ISO 15190:2020 — medical laboratories, requirements for safety (checked 22 October 2026)
- ISO 15189:2022 — medical laboratories, requirements for quality and competence (checked 22 October 2026)
- ISO 35001:2019 — biorisk management for laboratories and other related organisations (checked 22 October 2026)
- ISO 11607-1:2019 — packaging for terminally sterilized medical devices (checked 22 October 2026)
- ISO 11607-2:2019 — validation requirements for forming, sealing and assembly processes (checked 22 October 2026)
- ISO 15223-1:2021 — symbols to be used with medical device labels (checked 22 October 2026)
- CLSI PRE01 — Patient and Laboratory Specimen Identification Processes (checked 22 October 2026)
- CLSI GP42 — Collection of Capillary Blood Specimens (checked 22 October 2026)
- Public Health Ontario — Test Information Index (checked 22 October 2026)
- Fraser Health — About Fraser Health (checked 22 October 2026)
- Transport of High-Risk Infectious Substances: packaging for Category A specimens (checked 22 October 2026)
- Design and Characterization of a Novel Blood Collection and Transportation Device for Proteomic Applications (checked 22 October 2026)
- The false-positive rate of synovial fluid culture at a single clinical laboratory (checked 22 October 2026)
- Sample rejection rate and reasons for rejection among clinical specimens requested for diagnostic testing (checked 22 October 2026)
Write it down once: download the specimen pack-out SOP template and fill in the bag sizes, absorbent capacity and courier documents your own site uses.
If you would rather work backwards from volume, the clinic supply planner turns specimens per week into bags per quarter with a reorder point.
Related Reading
- 95 kPa specimen bags versus 3-wall transport bags: which one for which sample
- Specimen transport bag design: which construction actually prevents leaks
- Choosing UN3373 Category B packaging for specimen transport
Frequently Asked Questions
Do research laboratories in British Columbia need UN3373 bags or 95 kPa bags?
Both, and for different jobs. UN3373 is the shipping mark for Category B biological substances; a bag is marked UN3373 when it forms the secondary packaging of a compliant triple package. 95 kPa is a pressure-withstand claim on the bag itself. A 3-wall bag with an absorbent layer and an external document pocket is the usual choice for a secondary package holding primary containers, while a 95 kPa bag is specified when the laboratory wants the pressure claim printed on the bag. Confirm which mark your courier and receiving laboratory accept before a case is opened.
What size specimen transport bag does a research laboratory order first?
Most Lower Mainland and Island laboratories start with 6 x 9 in (about 150 x 240 mm) because it holds two or three primary containers plus the paperwork, then add 8 x 10 in for tube racks and 12 x 15 in for bagged secondary sets. Order the size mix the bench actually produces rather than one size for everything: an oversized bag lets containers slide and a tight bag cannot close over the document pocket.
What has to be printed on the bag itself?
The UN3373 mark with the words BIOLOGICAL SUBSTANCE, CATEGORY B, the responsible person's name and telephone number, a biohazard symbol, and orientation arrows where the package design calls for them. ISO 15223-1 gives the symbol set manufacturers use on the label. Anything the receiving laboratory needs in order to log the sample, such as study code, site code or temperature class, is pre-printed or written in the external pocket.
How many bags come in a case, and how are they packed?
The 6 x 9 in 3-wall bag is normally 100 bags per pack and 10 packs per case, so 1,000 bags per case. The 95 kPa lines usually ship 100 per pack in 6 x 9 and 8 x 10 in, with the 12 x 15 in format packed at a lower count per case because of the film area. Ask for the inner pack count as well as the case count, because bench staff restock from the inner pack.
What lead time should a British Columbia laboratory plan for?
Treat two to three business days as normal for stock held in the Lower Mainland and five to ten business days for a size that has to be brought in. A laboratory running a fixed weekly courier pickup should hold four to six weeks of bags, which is two cases for a bench that ships twenty to thirty specimens a week.
Can the same bag carry urinalysis, microbiology and molecular work?
The bag can, the paperwork usually cannot. Urine chemistry, bacterial culture and molecular assays each have their own container, temperature and timing rules, and the bag has to be large enough to carry the primary container plus the requisition without folding the requisition. Laboratories that run all three benches usually keep two sizes rather than one compromise size.
What happens if the bag arrives without an absorbent layer?
Under IATA packing instruction P650 the secondary packaging has to contain enough absorbent material to take up the entire liquid volume of the primary containers. A bag without an absorbent layer fails that requirement even when nothing has leaked, and a receiving laboratory is entitled to reject the shipment. Three-wall bags build the absorbent layer into the bag; two-wall bags require a separate pad.
How should bags be stored before use?
Keep them flat, out of direct sunlight and away from solvent vapours, in the original carton, at ordinary room temperature. Pressure claims and adhesive closures both depend on the material staying clean, so a bag left on a window sill or beside a disinfectant spill is no longer a bag with the same specification.
Last updated: October 2026. CliniEco Medical is a licensed medical device establishment (MDEL #35334).