What an Infection Control Auditor Checks About Gracey Curettes and Ultrasonic Scaling Tips
An infection control auditor working through a hygiene operatory spends little time on paperwork and a lot on the instruments. A Gracey curette and an ultrasonic insert are the two thinnest working ends in the room, both are critical, and both wear out in ways a pass at the chair will miss.
Cleaning comes first, because a worn edge is hard to judge on a soiled instrument. A 4 L benchtop ultrasonic cleaner that takes a full cassette, dosed with a low-foam multi-enzyme concentrate, clears the blade and the shank without the handling that bends a thin curette.
Why are scaling instruments critical?
Because of where they work. Ontario's IPAC dental checklist places periodontal scalers and ultrasonic scaler tips in the critical group, alongside all surgical instruments, and requires cleaning plus sterilization per the manufacturer's instructions between patients. Subgingival scaling reaches into the gingival sulcus and contacts blood, so the endpoint is a sterile instrument, not a disinfected one.
| Item | Wear or failure point | What the auditor inspects |
|---|---|---|
| Gracey curette, blade | rounded edge, nicks, burnished corner | blade under light, both cutting edges, no reflection break |
| Gracey curette, shank | bent or sprung shank | straight shank, tip alignment with the handle |
| Ultrasonic insert, tip | flattened or chipped tip, cracked stack | tip against the maker's gauge, no crack at the joint |
| Ultrasonic insert, base | worn or missing O-ring, loose seating | insert seats fully, torque as instructed, O-ring intact |

What does the auditor check on a Gracey curette?
The blade, and then the shank. A curette sharpened repeatedly loses its cross-section, and a rounded edge burnishes calculus instead of cutting it — the instrument is cleanable, sterile and still not fit for use. Nicks along the cutting edge are the second finding, because a nicked blade tears tissue and leaves a surface that holds soil.
Design and dimensions are standardised, which makes comparison possible: ISO 13397-2:2005 specifies the designs and dimensions of Gr-type periodontal curettes, and its Amendment 1:2012 adds the colour coding practices use when reordering a blade shape. ISO 13397-1:1995 sets general requirements across curettes, scalers and excavators.
What does the auditor check on an ultrasonic insert?

Three things. Whether the tip has worn, judged against the maker's indicator rather than by eye at arm's length. Whether the insert seats properly, since a loose insert with a perished O-ring leaks and loses power. And whether it was cleaned as its own instructions allow, because insert bodies are commonly hand-cleaned with the upper section kept out of the bath — an insert that ran through the curette cycle is a finding even when it looks fine.
Does any standard set a sharpening interval?
No, and that surprises practices that expect one. The ISO 13397 series defines the shape, dimensions and marking of these instruments; it does not set a service life or a sharpening frequency, and no Canadian standard does either. The control therefore sits in the practice's own procedure: a defined inspection at each cycle, a sharpening or replacement trigger, and a record that shows the rule was followed.
How should they be cleaned and packed?
Curettes go into the cassette with the working ends protected from each other, through the ultrasonic cycle, then a rinse and a dry; inserts follow their own instructions. Both are packed so the tip cannot touch the film, in a pouch sized to the instrument rather than the cassette, sealed and labelled with the date and cycle so pack and load record agree.
Ordering for a dental practice or a hygiene group? Wholesale and multi-site ordering covers case pricing and account setup, and the B2B wholesale collection lists lines stocked for institutional buyers. Reselling? become a distributor.
Running a dental practice? The dental practice supply page groups the ultrasonic chemistry, pouches and inspection sheets a hygiene team reorders.
Printable companion: the free compliance log set includes an instrument inspection sheet with the blade and tip fields above; the supply and cost planner converts hygiene days into chemistry and pouch quantities. Ask a compliance specialist if a worn instrument keeps coming back into the set.
References
- IPAC checklist for dental practice, core elements — Public Health Ontario (checked 12 November 2026)
- CSA Z314:23, Canadian medical device reprocessing in all health care settings — scope (checked 12 November 2026)
- Guidance document: information to be provided by manufacturers for the reprocessing and sterilization of reusable medical devices — Health Canada (checked 12 November 2026)
Related Reading
- Which Gracey Curettes and Ultrasonic Scaling Tips Should an Ontario Dental Clinic Buy? Selection Checklist
- How Many Gracey Curettes and Ultrasonic Scaling Tips Does a Dental Clinic Need Per Operatory? in Quebec
Frequently Asked Questions
Can ultrasonic inserts go in the ultrasonic cleaner?
Not as a default. Insert makers commonly specify hand cleaning and restrict immersion above the O-ring, so the practice's procedure has to follow the insert instructions rather than the curette cycle.
How is scaling tip wear measured?
Against the maker's wear indicator or a comparison gauge, at each inspection. There is no standard interval and no pass mark across brands.
Do Gracey curettes need sharpening records?
No standard requires a record, but a practice that sharpens on a fixed schedule and documents it can show how blade condition is controlled.
Last updated: November 2026. CliniEco Medical is a licensed medical device establishment (MDEL #35334).