What Happens If You Skip a Daily Biological Indicator Test in Ontario

Six CliniEco 24-hour self-contained biological indicators from a 50-pack, standing upright on a white background

Quick facts

  • Ontario's dental regulator requires spore testing each day the sterilizer is used, plus a control test, with both results written into a logbook.
  • A missing day is a documentation gap, not a positive result, and the two are handled very differently.
  • Loads processed on the missing day carry no biological evidence; mechanical and chemical monitors are all that remain behind their release.
  • The weekly spore test that circulates online is the United States baseline (CDC), not the Ontario requirement.
  • ISO 11138-3 is the standard that defines the biological indicators used for moist heat sterilization.
  • A complete entry carries the cycle date, cycle type, indicator lot, incubator used, result, control result, and who read it.

A spore test that is not run does not disappear. It leaves a date in the sterilization record with no biological indicator result behind it, and in Ontario that date is the first thing a reviewer looks for when the logbook is opened. This page sets out what the daily rule covers, what a missing day actually looks like in the record, what has to happen to the loads that were processed during the gap, and how a clinic closes the gap without rewriting its own history. A daily test only stays daily if the supply line makes it routine: the 24-hour self-contained biological indicators, 50-pack and the 24-hour dry-block incubator are the two items the schedule actually consumes.

What does Ontario require on every day the sterilizer is used?

The requirement is not spread across a dozen documents. The Royal College of Dental Surgeons of Ontario states it in one sentence: "Spore testing (biological indicators) must be done each day the sterilizer is used and the results of the test recorded in a logbook. A control test must also be used when spore testing is performed and those results also recorded." Three obligations sit inside that sentence, and clinics that fail an audit usually fail the third rather than the first.

Test. One biological indicator per sterilizer on each day that sterilizer processes a load. Two units in service on the same day are two tests, not one test and an assumption.

Control. An unprocessed indicator from the same lot, incubated beside the test vial, proves the incubator, the media and the spores were alive. Without it, a negative result has no reference point.

Record. Both results go into the logbook, and the logbook is the artefact that gets reviewed. The same College guidance tells clinics to mark the date of sterilization on the product wrapping, which is the only way a wrapped pack can later be matched to a load entry.

The same document also settles a packaging point that shows up in the same audits: pouches should not be overloaded, and instruments should not touch or overlap. A pack that was too full is a pack whose biological result describes a load that never really existed.

How often must a clinic in Ontario test, and how does that compare with the United States?

The advice that circulates most widely online is weekly, and it comes from the United States. The CDC's dental infection-control guidance says a spore test "should be used at least weekly to monitor sterilizers, and should use a matching control", and adds a second rule that applies on both sides of the border: a spore test should also be used for every load that contains an implantable device.

The difference is therefore not a difference of principle but of cadence. A clinic in Ontario runs the test on every day of use; a clinic in the United States runs it at least weekly, with implant loads covered individually. Copying the weekly figure into an Ontario logbook produces a record that looks imported, because the gaps fall on ordinary working days.

Item Canada (Ontario, RCDSO) United States (CDC baseline)
Minimum biological monitoring Each day the sterilizer is used At least weekly per sterilizer
Control indicator Required with each spore test, result recorded Matching control from the same lot
Implant loads Covered by the daily test; quarantine until negative is clinic policy Every implant load monitored; items quarantined until result known
Record location Logbook entry for the day Facility log; state and accreditation rules add detail
Who states the rule Provincial dental college standard National guidance, plus state and CMS requirements
Chemical monitoring External and internal indicator on the pack Class 1 process indicator plus internal indicator
Packaging note Pouch not overloaded; date of sterilization on the wrap Follow the packaging manufacturer's instructions

The two columns converge on one point that matters more than the cadence: the biological indicator is the only monitor that measures the killing power of the cycle directly. Chemical indicators respond to conditions, not to lethality, and the CDC guideline is explicit that they should be used alongside biological indicators rather than as a substitute.

What does a missing day look like in a sterilization record?

A gap is rarely an empty page. In practice it takes five shapes, and each one looks different to the person reading the log.

The date is simply absent. Cycle records for the day exist, appointment records show instruments were used, and the monitoring sheet jumps from Monday to Wednesday.

The entry exists without a result. A line was ruled and dated, the lot number written in, and the result column left blank because the vial was never read.

The result exists without a control. A negative is written in, but there is no paired control line, so nothing in the record shows the incubator was working that morning.

The result exists without a matching incubator sheet. The vial is recorded in the logbook, but the incubator log for the same date shows a different number of wells loaded, or no run at all.

The entry was added later. Ink, handwriting and position in the log all disagree with the surrounding entries, which is the pattern a reviewer notices first because it is visual rather than numerical.

None of these shapes is fixed by writing a result in after the fact. A backfilled entry converts a missing test into a record that misstates what happened, which is a different and more serious problem than the gap itself.

Do Ontario and the United States treat a released load the same way when a test is missing?

Those loads were released without biological evidence. That is the plain description, and it is the sentence an inspector will use. What follows depends on what is still in the building.

Instruments still in sterile storage. They can be recalled and reprocessed at the cost of the packs and the time. This is the lowest-cost resolution available and the one most clinics take.

Instruments already used. They cannot be recalled. The clinic documents what was processed, on which cycle, and that no biological result exists for it, then records the clinical judgement that was applied. A record that says nothing is worse than a record that states the exposure honestly.

Implantable devices. These are treated differently on both sides of the border. The CDC guidance keeps implant items quarantined until the biological result is known, and the safest reading of a missing result is that the quarantine condition was never satisfied.

If a later test does come back positive, the recall window widens: the CDC guideline describes the conservative approach in which material processed from the last negative indicator forward is treated as non-sterile. A missing test removes the reference point that window depends on, which is why reviewers treat a gap as a release-of-load problem rather than a clerical one.

How should the gap be closed without rewriting the log?

The corrective action record does the work. It is a separate document that describes what was found, what was done with the affected loads, and what changed so the same gap does not recur. The logbook stays as it was, with the gap visible in it.

Record element What it must show Why it is asked for
Date and unit The specific day and which sterilizer has no result Ties the gap to a machine and a load list
Loads affected Cycle numbers, pack counts, and where the instruments went Defines what can still be recalled
Disposition Reprocessed, quarantined, or used with documented reasoning Shows the decision was made by a named person
Cause Staff absence, supply stockout, incubator fault, or schedule failure Separates a supply problem from a habit problem
Corrective action Who now runs the test, when, and what the backup is The part an inspector reads to decide if it will recur
Effectiveness check A later period reviewed to show the gap did not repeat Closes the loop in the file

Two mistakes are common here. The first is treating the corrective action as an apology rather than a record, which leaves out the load list and the disposition. The second is leaving the cause at "human error", which is true of nearly every gap and tells the reader nothing about prevention. A stockout is a supply-planning failure and is fixed by a par level; a forgotten test is a schedule failure and is fixed by putting the test on the opening routine.

Which consumables keep a daily test practical?

A daily schedule across one sterilizer consumes five to six indicators a week, plus a control vial each day the test is run. That is the arithmetic behind a 50-pack: roughly six to eight weeks of coverage for a single-unit clinic, which is long enough to plan the next order rather than to discover a stockout on a Tuesday morning.

The incubator is the second half of the routine. Our dry-block unit holds 24 wells, runs at the temperature the indicator manufacturer specifies, and takes both the test vial and the control vial in the same run, so the two results are read side by side rather than days apart.

The packaging line matters for the same reason the log does: a pouch that is too small for the instrument forces the film to stretch, and a stretched pack is the failure that turns up in the inspection rather than at the bench. The Class 4 self-sealing dual-indicator pouch, 200 per box carries an external process indicator and a write-on area for the date the College asks for.

Six CliniEco 24-hour self-contained biological indicators from a 50-pack, standing upright on a white background CliniEco 24-hour biological indicator dry-block incubator, closed lid, on a white background

Single-unit and multi-site clinics buy the monitoring line on an institutional account: institutional account enquiries cover case quantities, standing orders and the documentation pack that travels with the indicators. The full monitoring range sits in the sterilization monitoring collection. Reselling? become a distributor.

Sources

  1. RCDSO — Infection prevention and control in the dental office: some common questions
  2. CDC — Sterilization monitoring in dental settings
  3. CDC — Guideline for Disinfection and Sterilization: sterilizing practices
  4. ISO 11138-1:2017 — Biological indicators, general requirements
  5. ISO 11138-3:2017 — Biological indicators for moist heat sterilization
  6. ISO 11140-1:2014 — Chemical indicators, general requirements
  7. ISO 17665-1:2006 — Moist heat sterilization, requirements for development and validation
  8. ISO 15883-1:2024 — Washer-disinfectors, general requirements
  9. ISO 17664-1:2021 — Information to be provided by the medical device manufacturer for reprocessing
  10. CSA Group — CSA Z314:23, Reprocessing of medical devices in health care settings
  11. Medical Devices Regulations, SOR/98-282 (consolidated text)
  12. Ordre des dentistes du Quebec
  13. FDA — Medical device classification database
  14. openFDA — Device classification API
  15. Public Health Ontario — Infection prevention and control
  16. ASTM F1929-23 — Detecting seal leaks in porous medical packaging by dye penetration

The monitoring sheet this page describes is the one in the free sterilization log pack, which includes the daily biological indicator record and the load-release blocks that sit beside it. The same page hosts a sterilization log generator that prints a dated sheet for the current month, so the gap described above has a place to be recorded the moment it is found.

A clinic that wants the frequency verified against its own provincial college, or a documented corrective action reviewed before an inspection, can ask a sterilization compliance specialist rather than work it out from a supplier page.

Related reading

CliniEco Medical supplies sterilization monitoring consumables in Canada under MDEL #35334. This page describes regulatory expectations and clinic practice; it is not a substitute for the standard issued by your provincial college. Institutional account enquiries are handled through the account enquiry page.

Frequently Asked Questions

Is a missed spore test the same as a positive spore test?

No. A positive test is a result that says the process failed; a missed test is the absence of a result. A positive result starts a defined response (remove the unit from service, repeat the test, hold implant loads). A missed test starts a documentation response: identify the loads, decide their disposition, and record the corrective action without backfilling the log.

Does Ontario require a test on a day with only one small load?

The College wording is tied to use, not to volume: the test is required each day the sterilizer is used. A single small load still counts as use, and a clinic that runs a unit once a week still owes a result for that day.

Can the test simply be run the next morning instead?

Running it late does not create a result for the day that was missed. Record the late test on the day it was run and treat the earlier day as a gap with its own disposition entry, because the loads processed in between were released without biological evidence.

Why is a control indicator required every time?

The control vial is unprocessed and must grow. If it does not, the incubator, the media or the spore strip is at fault and the negative result beside it proves nothing. A negative test without a control is an unverified negative.

How long should the spore test log be kept?

Follow the records schedule of your provincial college and your own facility policy; the working rule most clinics adopt is the life of the sterilizer plus the retention period that applies to patient records, on the basis that a patient treated years earlier can still raise a question about a load.

Where do the results go if the clinic uses a service rather than an in-house incubator?

The result still has to be recorded in the clinic log with the date, the unit and the lot. A service report filed in a drawer does not satisfy the requirement that the results of the test be recorded in a logbook.

Already working with clinics? Become a regional representative.