Pouch sizing in Canada is a two-language problem. The same pouch is printed as 3.5 x 9 inches on the front of the box and 90 x 229 mm on the side, and those two statements are usually describing the same product — but not always the same measurement. A buyer who orders by the imperial figure and inspects by the metric figure can end up rejecting a correct shipment, or accepting one that is a few millimetres short of the cassette it has to hold. The practical reference in this comparison is the 3.5 x 9 inch pouch, which prints both figures on one box. This comparison sets out which number controls the fit, how the common sizes convert, and how Canadian and US catalogues differ in practice.
Why do Canadian pouches carry two sets of numbers?
Canada's prepackaging and labelling rules require metric net quantity on prepackaged consumer goods, while the North American medical supply trade has been built on inch dimensions. A pouch manufactured for the continent is therefore tooled in inches and labelled in both. The metric figure on the box is a conversion, not a second specification.
That distinction matters when the conversion is rounded. A 3.5 inch width is 88.9 millimetres, which is usually printed as 90 mm. A 9 inch length is 228.6 millimetres, printed as 229 mm — or sometimes as 230 mm. None of these is wrong, but none of them is the tooling dimension either. When you compare two suppliers' boxes side by side, a 2 millimetre difference in the printed metric figure is usually rounding, not a different pouch.
Which measurement should you order by?
Order by the internal usable dimension, and verify it with a ruler before you commit a case. The printed size refers to the pouch's outside dimensions in most catalogues, and the usable internal space is smaller once you account for the seal lines on both sides and the fold at the bottom.
A practical method takes about two minutes. Put the largest instrument or cassette you plan to process into a sample pouch and fold the opening closed. You want at least a centimetre of clear paper beyond the instrument on each side, and enough length to fold the flap over twice. A pouch that fits with no margin will burst at the seal when the air inside expands during the vacuum cycle.
| Printed size | Metric equivalent | Typical contents | Usable margin note |
|---|---|---|---|
| 2.25 x 4 inch | 57 x 102 mm | Single small instrument, probe covers | Tight for anything with a handle |
| 3.5 x 5.25 inch | 90 x 133 mm | Mirrors, scissors, small forceps | Common dental size |
| 3.5 x 9 inch | 90 x 229 mm | Handpieces, forceps, long mirrors | Workhorse size in dental |
| 5.25 x 10 inch | 133 x 254 mm | Small cassettes, corded handpieces | Check cassette width plus 2 cm |
| 7 x 13 inch | 178 x 330 mm | Large trays, multi-instrument sets | Consider roll stock above this |
How do you convert common pouch sizes without a calculator?
One inch is 25.4 millimetres. For the sizes that matter in a clinic, two anchor points cover most of the arithmetic: 2 inches is 51 millimetres and 5 inches is 127 millimetres. Anything between them can be estimated by adding 25 millimetres per inch, which is accurate enough to check a label but not accurate enough to design a cassette layout.
Work in one direction only. If your instruments are measured in millimetres, convert the pouch to millimetres and compare in millimetres. Converting back and forth introduces rounding twice, and rounding twice is how a 5.25 inch pouch becomes 130 mm in one catalogue and 135 mm in another.

Does Canada require metric labelling on pouch boxes?
Prepackaged products sold in Canada generally carry metric net quantity, which is why the metric figure appears on the box even when the tooling is imperial. That requirement concerns the declared quantity, not the manufacturing tolerance, so the metric number should be treated as a label rather than as a fit specification.
In practice this creates a small trap for buyers writing purchase orders. If your order says 90 x 229 mm and the shipment arrives with 3.5 x 9 inch printed prominently, check the metric figure on the same box before rejecting. Conversely, if your order says 3.5 x 9 and the delivered pouch measures 88 x 226 mm with a ruler, that is within normal manufacturing tolerance for a pouch sold as 3.5 x 9.
What differs in US catalogue practice?
US catalogues lead with inches almost universally, and often omit the metric figure entirely. That is a presentation difference rather than a product difference: the same converting lines supply both markets. Where the two markets genuinely diverge is in the assortment. US dental catalogues carry a deeper range of very small pouches and of self-seal versus heat-seal variants, while Canadian catalogues tend to concentrate on the dental workhorse sizes and on heat-seal roll stock.
For a Canadian clinic buying from a US-listed supplier, two practical differences matter. First, the SKU may be identical but the packaging label may lack the metric figure, which complicates your own receiving record. Second, sizes sold as a case in the US may be packed 200 per box or 500 per box, so compare the price per pouch rather than the case price.

Which size should a Canadian clinic order for cassettes and handpieces?
For loose handpieces and long forceps, 3.5 x 9 inch covers most dental needs. For a single small cassette, 5.25 x 10 inch is the usual entry point, but measure the cassette's outside width and add two centimetres before you commit. Cassettes that are 130 mm wide will not fit comfortably in a 133 mm pouch once the seal lines are counted, and the failure mode is a seam that splits during the vacuum phase.
For multi-instrument trays above roughly 300 mm in length, move to roll stock rather than the largest pouch. A sealed pouch that is overfilled has no room for air expansion, and the seal is the first thing to fail. Keeping two pouch sizes plus one roll width covers almost every Canadian dental and clinic load pattern without stocking a size you use twice a month.
Download the printable pouch size and load log, check your monthly volumes with the clinic supply planner, and if a seal fails after a size change, ask a sterilization compliance specialist before releasing the load.
The sizes referenced above are stocked as the 3.5 x 9 inch Class 4 dual indicator pouch and the 5.25 x 10 inch Class 4 dual indicator pouch, both printed with the inch and metric figure on the same box.
Ordering for a clinic, lab or care home? Wholesale and multi-site ordering covers case pricing and account setup, and the B2B wholesale collection lists the lines stocked for institutional buyers. Reselling? become a distributor.
Related reading
sterilization compliance hub · pouch case sizes and price per pouch · pouch size for dental cassettes: a measurement method · roll widths for Canadian clinics
Frequently Asked Questions
Is a 3.5 x 9 inch pouch the same as 90 x 229 mm?
Effectively yes. 3.5 inches is 88.9 mm and 9 inches is 228.6 mm, so the printed metric figure is a rounded conversion of the imperial tooling dimension. A few millimetres of variance between suppliers is normal rounding.
Should I order pouches by inches or millimetres in Canada?
Order by the internal usable dimension and state it in one unit only. Most Canadian catalogues lead with inches, and the metric figure on the box is a label conversion, so the inch figure is usually the tooling specification.
What size pouch fits a dental instrument cassette?
A 5.25 x 10 inch pouch suits many small cassettes, but measure the cassette's outside width and add two centimetres for the seal lines. Cassettes wider than about 130 mm need the next size up or roll stock.
Why does my pouch split at the seal during the vacuum cycle?
Usually because the pouch is overfilled. Air inside expands during the vacuum phase and pushes against the seal. Leave at least a centimetre of clear paper on each side of the instrument and fold the flap twice.
Are US pouch sizes different from Canadian ones?
The dimensions are the same, but US catalogues lead with inches and often omit the metric figure, and case counts per box differ. Compare price per pouch rather than case price when buying across the border.
CliniEco Medical is a licensed medical device establishment (MDEL #35334).