Do You Need a Process Challenge Device for Every Spore Test?

A process challenge device places a biological indicator or chemical indicator inside a stand-in load that is harder to sterilize than a normal instrument tray. Regulators do not demand a PCD for every spore test, but they do expect the spore test to represent the worst-case load you actually run. Where you use a PCD, it should be matched to the load type and documented in the same log as the spore result.

What is a process challenge device?

A process challenge device, usually shortened to PCD, is a holder that creates a defined resistance to steam so the biological indicator inside faces conditions at least as hard as the real load. It exists because a spore strip sitting loose in an empty chamber can pass even when a densely packed instrument tray would fail. By standardizing that resistance, a PCD makes the spore test meaningful: a pass means the sterilizer handled the difficult case, not just the easy one. PCDs come as commercial test packs, as trays with lumen challenges, or as validated in-house assemblies, but the principle is the same in every format.

Do you need a PCD for every spore test?

Not every test, but the test must represent the worst case in your practice. Where a clinic runs routine instrument sets, a PCD-based spore test is the standard way to make that representation credible. Guidance generally expects the biological indicator to be placed in a challenge that matches the most difficult load you process, which in many dental and clinic settings means a PCD. A loose spore strip is still better than no test, but it can mislead when the real loads are packed tighter than the strip's surroundings.

How do the common PCD formats compare?

Different PCD formats create resistance in different ways, and the right one depends on your load mix.

CliniEco Medical 24-hour self-contained biological indicator, 25-pack, used for process monitoring and re-verification after HVAC work in a reprocessing area
Format How it challenges the cycle Suitable for
Commercial test pack Standardized mass and wrapping Routine dental and clinic sterilizers
Lumen challenge Narrow tube resists steam penetration Hollow or cannulated instruments
Tray-based PCD Simulates a real instrument tray High-volume sets
In-house validated device Built to match a specific load Facilities with unusual loads

How should a PCD be used and recorded?

Place the device where a routine load would sit, then run the cycle and incubate the indicator as usual. Record which PCD was used, the load it represented and the result, so a reviewer can see the test matched the practice. Rebuild or replace the device on the manufacturer's schedule, because a worn PCD loses its resistance and no longer tests the worst case. If a PCD-based spore test fails, hold the loads that share that challenge until the cause is fixed and a retest passes.

Reading the result quickly

A PCD is only useful if the spore result comes back in time to guide a release decision. A 24-hour rapid-readout biological indicator 50-pack gives a same-day answer, and a 30-minute fluorescence rapid-readout indicator shortens that further for busy clinics. Pair the device with a fast indicator so the challenge actually informs the decision rather than trailing behind it.

Ordering for a clinic, lab or care home? Wholesale and multi-site ordering covers case pricing and account setup, and the B2B wholesale collection lists the lines stocked for institutional buyers. Reselling? become a distributor.

24-hour rapid readout biological indicators for daily sterilizer monitoring

Related Reading

Not sure which consumable fits your set-up? Start with the Request 5 free biological indicators.

Take this further: print the free sterilization log and record templates, run the cycle log generator, or ask a compliance specialist to review your setup.

Frequently Asked Questions

Is a PCD required for every biological indicator test?

Not by every regulator, but the spore test must represent your worst-case load. A PCD is the usual way to make that representation credible in a busy clinic.

Can a loose spore strip be used without a device?

It can be used, but it may pass where a packed tray would fail. A device recreates the resistance of real loads and gives a more meaningful result.

How often should a PCD be replaced?

Follow the manufacturer's schedule and replace it sooner if it shows wear. A worn device loses resistance and no longer tests the difficult case.

CliniEco Medical is a licensed medical device establishment (MDEL #35334).

Already working with clinics? Become a regional representative.