Periodontal Probes: Markings, Tip Diameter, ISO 21672

Stack of green two-layer paper dental bibs wrapped in clear film

Quick facts

  • In the United States a periodontal probe is Class I under 21 CFR 872.4565 — the dental hand instrument regulation — product code EIX, "Probe, Periodontic" (openFDA, read 2026-10-20).
  • ISO 21672-1:2012 is Dentistry — Periodontal probes — Part 1: General requirements (catalogue entry read 2026-10-20).
  • The two marking patterns a clinic meets most often are the millimetre scale (1 to 15 mm) and the banded pattern used for screening, where bands rather than single millimetres are read.
  • Tip diameter decides how far the probe penetrates the sulcus, so two probes with different tip diameters are two different measurements, not two views of the same one.
  • A periodontal chart records six sites per tooth; a probe that is bent, blunted or has lost its markings produces a chart that looks complete and is not.
  • Pages were read on 2026-10-20; the eCFR section, the openFDA API and the ISO catalogue entry returned 200.

A periodontal probe is a millimetre scale on a handle, and its readings become a chart that follows a patient for years. That makes the specification matter more than the price: the marking pattern decides what can be read, the tip diameter decides what is being measured, and the condition of the tip decides whether the numbers mean anything. This article compares the marking patterns and tip designs a Canadian practice chooses between, explains how the probe is classified, and sets out the inspection and reprocessing rules that keep a chart comparable. Probes are pouched with the rest of the tray, which is why the 5.25 x 10 inch sterilization pouches are ordered on the same cycle as the instruments.

What do the markings on a periodontal probe mean?

A periodontal probe is read at the gingival margin and the depth is the distance from the margin to the base of the sulcus or pocket. The marking pattern is what makes that distance readable at a glance, and there are two families in common use.

The millimetre scale marks every millimetre from 1 to 15, which allows a single-site reading to the nearest millimetre and is the pattern used where detailed charting is the point. The banded pattern marks bands rather than single millimetres, which is faster to read and is designed for screening: the clinician records which band the depth falls into rather than a precise figure.

The two are not interchangeable in a chart. A site recorded as "band 2" and a site recorded as "5 mm" are different kinds of data, and a practice that changes pattern mid-treatment creates a chart that cannot be compared with itself.

Why does tip diameter change the reading?

A probe tip has a diameter, and a wider tip meets more resistance in the sulcus and penetrates less deeply than a fine one at the same force. That is why two probes with different tip diameters can give different depths on the same site, and why the tip diameter belongs in the specification of a probe rather than in a footnote.

The practical consequence is consistency. A practice should use one tip diameter for charting, so that a change in the chart reflects a change in the patient rather than a change in the instrument. Where a finer tip is used for a specific purpose, the chart should say so.

ISO 21672-1:2012 sets general requirements for periodontal probes. As with any instrument standard, it defines what the instrument must be; it does not decide which pattern or tip diameter a practice should standardise on.

Which probe fits which job?

Probe Marking pattern Tip Where it fits What to check before buying
Millimetre probe 1 to 15 mm, single millimetres Standard fine tip Full periodontal charting Marking legibility, tip straightness, handle grip
Banded screening probe Bands rather than single millimetres Ball-ended tip Screening and epidemiology-style recording Band width, ball diameter, marking contrast
Furcation probe Curved or offset shank Blunt tip Furcation involvement Shank curve, tip bluntness, access
Plastic probe Millimetre or banded Plastic tip Implant sites and restored surfaces Tip wear, replacement interval
Automated probe Constant-force mechanism Controlled tip Research and calibration Calibration record, repair route, cost per unit

Periodontal probes: Canada and the United States

Item Canada United States
Classification Class assigned by the manufacturer under SOR/98-282 Class I, 21 CFR 872.4565, product code EIX
What the regulation covers Instrument as placed on the market Dental hand instruments, including periodontal probes
General requirements ISO 21672-1:2012 used by manufacturers ISO 21672-1:2012 used by manufacturers
Reprocessing Provincial IPC standard plus the manufacturer's instructions CDC guidance plus the manufacturer's instructions
Chart record Six sites per tooth, pattern and tip noted Six sites per tooth, pattern and tip noted

How should a probe be inspected?

Check the tip first. A bent tip is a probe that measures a different depth, and a bent tip is easy to miss at the end of a long day. Roll the probe against a flat surface or sight along the shank; a tip that is out of line is out of service.

Check the markings next. Repeated cycles dull the contrast, and a probe whose 5 mm line has worn to a smudge is a probe that will be read as 4 or 6 depending on the light. Markings are the measurement, so a worn marking is a failed instrument.

Check the handle and the shank junction for cracks, and check plastic probes for tip wear, which is faster than metal wear and often invisible without magnification. Record the inspection on the same sheet as the instrument checks the practice already keeps.

How is a probe reprocessed?

A probe is a semicritical or critical instrument depending on the tissue it contacts, and in a dental practice it goes through the same clean, package and sterilize chain as the rest of the tray. Cleaning comes first, because a probe with debris at the tip is a probe with a covered surface.

Then packaging that allows steam contact and sterilization according to the manufacturer's instructions. ISO 17664-1:2021 sets out what the manufacturer must tell the reprocessor, and the practice should be following that document rather than a colleague's habit.

Plastic probes have their own limits: they may not tolerate the same cycle as stainless steel, and their markings may wear faster under repeated processing. Where a plastic probe is used for implant sites, the reprocessing instruction and the replacement interval come from the manufacturer, not from the metal probe next to it in the drawer.

Stack of green two-layer paper dental bibs wrapped in clear film

How does the probe fit into the chart?

The chart records probing depth at six sites per tooth, plus bleeding on probing and any recession, and the probe is the instrument that produces the depth. The chart is only as comparable as the instrument and the technique behind it, which is why the pattern and the tip diameter belong in the practice's periodontal protocol.

Where a practice changes probes, the change should be recorded as a change of method. A chart that jumps from 3 mm to 4 mm across a whole dentition is more often a new probe than a new disease, and a note that records the change saves a clinical conversation later.

Keep the protocol short: one pattern, one tip diameter, six sites, bleeding recorded, and a stated inspection rule. That is enough to make the chart worth keeping, and it is short enough that a new hygienist can follow it in the first week.

Six rolls of white cotton roll on a white background

Probes are bought with the instruments that share their tray, and the pouches that carry them are reordered on the same cycle. Order through the wholesale programme for case pricing and an account, or become a distributor for resale. The 5.25 x 10 inch sterilization pouches, 200 pack sits in the same catalogue. Consumables for this line are listed under the department page.

Sources

  1. 21 CFR 872.4565, dental hand instrument
  2. openFDA, device classification API (read 2026-10-20)
  3. FDA, device classification database
  4. ISO 21672-1:2012, dentistry, periodontal probes, general requirements
  5. ISO 17664-1:2021, processing of health care products, information to be provided by the medical device manufacturer
  6. ISO 11607-1:2019, packaging for terminally sterilized medical devices
  7. ISO 10993-1:2018, biological evaluation of medical devices
  8. Medical Devices Regulations, SOR/98-282
  9. Health Canada, medical devices
  10. Health Canada, establishment licensing
  11. RCDSO, infection prevention and control standard
  12. Canadian Dental Association
  13. College of Dental Hygienists of Ontario, standards
  14. Public Health Ontario, infection prevention and control
  15. CDC, guideline for disinfection and sterilization in healthcare facilities
  16. Canadian Centre for Occupational Health and Safety, OSH answers

Probe inspection and discard log. A page that records each probe in service, its marking pattern, tip condition and the date it was removed, so that a chart change can be traced to an instrument change. Print the probe inspection log — plain paper, no account and no sign-up, and it is short enough to complete at the end of a hygiene day.

Periodontal charting protocol card. A one-page card that fixes the pattern, the tip diameter, the six sites and the bleeding convention, so that two hygienists produce comparable charts. Print the charting protocol card and keep it with the charting sheets rather than in a policy binder.

Ask a compliance specialist. Whether a plastic probe can go through the same cycle as a steel one, what the packaging must state and how a change of probe should be recorded are questions that depend on the instrument and the province. Ask a compliance specialist — written answer specific to your equipment and province, with the regulation or standard it is based on cited.

Related reading

CliniEco Medical supplies eye care, laboratory and dental consumables of the kind described in this article. MDEL #35334. This article is written for practice managers and is not clinical advice; probing technique, force and the interpretation of a periodontal chart belong to the treating dentist or hygienist under the standards of the provincial college.

Frequently Asked Questions

What class is a periodontal probe in the United States?

Class I under 21 CFR 872.4565, the dental hand instrument regulation, product code EIX. The probe does not have a regulation of its own, which is why a search for a periodontal probe by name returns nothing.

Does ISO 21672 cover periodontal probes?

ISO 21672-1:2012 is Dentistry — Periodontal probes — Part 1: General requirements. It sets general requirements for the instrument; it does not prescribe which marking pattern a practice should use.

What is the difference between UNC-15 and WHO markings?

UNC-15 marks every millimetre from 1 to 15, so a site can be recorded to the millimetre. WHO-style banded probes mark bands rather than single millimetres and are read as a band, which is faster but less precise.

Why do two probes give different readings on the same site?

Tip diameter and probing force both change penetration. A wider or blunter tip meets more resistance and reads shallower, so a practice should chart with one tip diameter and record any exception.

When should a probe be discarded?

When the tip is bent, the markings have lost contrast, the shank is cracked, or a plastic tip is worn. A probe whose markings cannot be read is a failed instrument, not a worn one.

Can plastic probes be sterilized like steel probes?

Only as the manufacturer instructs. Plastic probes may not tolerate the same cycle and their markings wear faster, so the reprocessing instruction and the replacement interval come from the manufacturer.

What should a periodontal chart record?

Six sites per tooth, probing depth, bleeding on probing, recession, and the probe pattern and tip diameter used. Recording the instrument is what makes two charts comparable.

Already working with clinics? Become a regional representative.