Is ASTM F2100 Mandatory in Canada? What the Medical Devices Regulations Require Instead

Close-up of a blue three-ply surgical mask showing pleat folds and ear loop welds

Is ASTM F2100 Mandatory in Canada? What the Medical Devices Regulations Require Instead

A purchasing manager in Mississauga opens a case of masks and reads the box: three-ply, level 2, ASTM F2100, made in Canada. She has ordered this product for four years. Then a new infection prevention lead asks a question nobody has asked before. Where, exactly, does it say that a mask in a Canadian clinic has to meet ASTM F2100?

The honest answer is that it does not say that anywhere in Canadian law. That answer is uncomfortable for about thirty seconds, and then it becomes useful, because it separates the two things a buyer is actually managing: the regulatory duty that applies to the product, and the performance question the clinic is trying to answer.

What does ASTM F2100 actually cover on a mask box?

ASTM F2100 is a specification for medical face mask materials and construction. It sets out performance requirements and the test methods used to demonstrate them, and it groups results into levels, which is what the box badge refers to.

Across the levels the standard addresses bacterial filtration efficiency, particle filtration efficiency, differential pressure, resistance to synthetic blood at a defined pressure, and flame spread. Level 1 corresponds to low fluid resistance, Level 2 to moderate fluid resistance and Level 3 to high fluid resistance, with the filtration thresholds tightening as the level rises.

The detail that matters commercially is that the standard is a specification, not a regulation.

That distinction is why the three products most Ontario clinics stock look almost identical on the shelf and behave differently in a procedure. The Aurelia ASTM Level 2 face mask, 50 per box is the routine-care mask; the CliniEco three-ply ASTM Level 2 procedural mask is the same level in a case format; and the CliniEco three-ply ASTM Level 3 mask, 250 per case is the one a splash-heavy procedure should name.

That distinction is why the three products most Ontario clinics stock look almost identical on the shelf and behave differently in a procedure. The Aurelia ASTM Level 2 face mask, 50 per box is the routine-care mask; the CliniEco three-ply ASTM Level 2 procedural mask is the same level in a case format; and the CliniEco three-ply ASTM Level 3 mask, 250 per case is the one a splash-heavy procedure should name. It tells a manufacturer what to test and a buyer what to expect. It does not tell a government what to enforce.

Is ASTM F2100 required by law in Canada?

No. Canadian requirements for a mask sold as a medical device come from the Medical Devices Regulations made under the Food and Drugs Act, and those regulations do not incorporate ASTM F2100 by reference.

Aurelia blue Level 2 face mask box, front view showing the level marking on the panel

What the regulations do is create duties around the product. Section 21 sets out what the label must carry. Section 44 requires an establishment licence for the activity of importing or selling a device, with exemptions that include the retailer and the health care facility, and it places a duty on the importer to satisfy itself that the establishment it buys from holds the licence. Those duties apply whether the mask is Level 1 or unlevelled.

So the answer to "is F2100 mandatory" is that the standard is voluntary and the label and licensing duties are mandatory. A clinic that thinks the badge is the legal requirement has the two halves the wrong way round, and that error has a practical cost: it stops people from checking the label, which is the part a regulator actually looks at.

Item Canada United States
Legal instrument Medical Devices Regulations (SOR/98-282) 21 CFR Part 878
Surgical mask classification Set by Canadian classification rules Class II, special controls (878.4040(b)(1))
Isolation mask classification Set by Canadian classification rules Class I (878.4040(b)(2))
ASTM F2100 legal status Consensus standard, not incorporated Consensus standard, recognised in FDA practice
Label duties Section 21 content list 21 CFR 801 and 878.4040 controls
Establishment duty Establishment licence, section 44 Establishment registration and listing

What must a mask label show under the Medical Devices Regulations?

Section 21 is a list, and it is worth reading once, because it is the only part of this article a regulator will hold you to. The label must carry the name of the device, the name and address of the manufacturer, the device identifier, an indication of contents where the contents are not readily apparent, the expiry date where the device has one, the intended use and performance specifications where those are necessary for proper use, the directions for use unless they are not required for safe and effective use, and any special storage conditions.

Subsection 21(2) adds the quality bar that gets missed in disputes: the information must be expressed in a legible, permanent and prominent manner, in terms that are easily understood by the intended user. A box printed in a font that cannot be read at arm's length in a supply room is a labelling problem, and the fact that the same information appears on an invoice or a website does not cure it.

Symbols on the box, including the single-use mark, are standardised in ISO 15223-1:2021, which is why the same symbol means the same thing on a mask box from any supplier and why a symbol is not a substitute for the words section 21 requires.

How is the same mask classified in the United States?

The US regulation is unusually specific, which makes it a useful mirror. Under 21 CFR 878.4040, surgical apparel includes surgical caps, hoods, masks, gowns, operating room shoes and shoe covers, and isolation masks and gowns. Within that group, surgical gowns and surgical masks are Class II with special controls, and everything else in the group is Class I.

Close-up of a blue three-ply surgical mask showing pleat folds and ear loop welds

The special controls are not decorative. They require the user-contacting components to be demonstrated biocompatible, they require nonclinical testing to characterise flammability in a way appropriate to the intended environment, and they require demonstration that the device resists penetration by fluids such as blood at a velocity consistent with its intended use. Those are the same questions a Canadian buyer is asking when they ask for a test report, which is why the two countries converge in practice even where the legal instruments differ.

Test question What it answers Standard that carries it
Filtration How much bacteria and particle load the media stops ASTM F2100 levels, EN 14683 types
Fluid resistance Whether a splash passes through to the wearer ASTM F2100 fluid resistance, synthetic blood method
Breathability Whether the mask is wearable for a full shift Differential pressure, EN 14683 pressure drop
Biocompatibility Whether contact materials are tolerable ISO 10993-5:2009 cytotoxicity testing
Manufacturing control Whether the batch is repeatable ISO 13485:2016 with a risk file under ISO 14971:2019
Splash method How synthetic blood resistance is demonstrated on protective clothing ISO 22609:2004

Which standard should go into a clinic's mask specification?

Pick the one your infection prevention lead already uses, and write it down with the level. A mask specification that says "medical mask" is not a specification; it is a hope. A specification that says "ASTM Level 2, test report on file, edition cited" can be checked by whoever receives the next shipment.

If your practice documents follow EN 14683 because a supplier's product line is European, use types rather than levels: Type I, Type II and Type IIR, where the Type IIR adds resistance to splashes. If your documents follow ASTM, use Level 1, 2 or 3. The two systems are not interchangeable, and a cross-walk between them should be treated as an approximation for conversation, not as a conversion factor for a policy.

What matters more than either standard is consistency. A clinic that has decided Level 2 for routine care and Level 3 for procedures with splash risk has a rule that staff can follow. A clinic that buys whatever is on promotion has a stockroom that cannot be audited.

How do you check the test report a supplier sends?

Three items on the page, in this order. First, the standard and its edition: a report citing an older edition of the same standard is not automatically wrong, but you should know which one you have. Second, the measurements against each requirement, not only the conclusion: a table that shows filtration efficiency, differential pressure and fluid resistance results tells you what the level was assigned on. Third, the laboratory and the date, because a report with no laboratory name cannot be verified and a report from 2019 describes a product line that may have changed since.

Two supporting questions are worth asking as well. Whether the manufacturer holds a quality management system certificate under ISO 13485:2016, because that is what makes batch-to-batch consistency plausible. And whether a risk file exists under ISO 14971:2019, because that is where the manufacturer records why the level chosen is appropriate for the intended use.

For a Canadian buyer, the receiving check closes the loop: the carton identifier, the manufacturer name and address, the expiry date and the storage conditions are all section 21 items, and all of them can be checked against the invoice on the day the pallet arrives. If your team already documents PPE receiving, run masks through the same form. Dental practices can use the dental practice supply and compliance page as the entry point for the products that sit alongside masks, and the ASTM F2100 mask levels reference page shows how the levels differ in use.

What does this mean when you place the next order?

Order by level and by report, not by badge. Then keep the paperwork with the product. The three masks most Canadian clinics settle on map to that approach: Aurelia face masks, ASTM Level 2, made in Canada, 50 per box for routine care, the CliniEco three-ply ASTM Level 2 procedural mask as the everyday case buy, and CliniEco three-ply ASTM Level 3 masks, 250 per case where splash risk is documented in the procedure. The wholesale collection holds the case formats if you are ordering across several rooms.

Ordering for a clinic, lab or care home? Tell our clinic and institutional supply desk which ASTM level your policy names and how many rooms you stock, and we will send the case quantities with the level written on the quote. Reselling? become a distributor.

References

  1. Medical Devices Regulations (SOR/98-282), section 21, label content (checked 11 November 2026)
  2. Medical Devices Regulations (SOR/98-282), section 44, establishment licence (checked 11 November 2026)
  3. 21 CFR 878.4040, Surgical apparel (US classification of masks and gowns) (checked 11 November 2026)
  4. 21 CFR 880.6250, Examination gloves (device identity, for contrast with apparel) (checked 11 November 2026)
  5. 29 CFR 1910.132, Personal protective equipment, employer duties (checked 11 November 2026)
  6. EN 14683:2019, Medical face masks, requirements and test methods (checked 11 November 2026)
  7. ISO 22609:2004, Clothing for protection against contact with blood, resistance to synthetic blood (checked 11 November 2026)
  8. ISO 15223-1:2021, Symbols to be used with information supplied by the manufacturer (checked 11 November 2026)
  9. ISO 13485:2016, Medical devices, quality management systems (checked 11 November 2026)
  10. ISO 14971:2019, Application of risk management to medical devices (checked 11 November 2026)
  11. ISO 10993-5:2009, Biological evaluation, in vitro cytotoxicity tests (checked 11 November 2026)
  12. Public Health Ontario, Routine Practices and Additional Precautions (checked 11 November 2026)
  13. Public Health Ontario, Infection Prevention and Control topic index (checked 11 November 2026)
  14. CCOHS, Gloves, selection and use in the same PPE stack (checked 11 November 2026)
  15. WHO, Health-care waste fact sheet, PPE disposal context (checked 11 November 2026)

Documentation pack: the SOP document package for imported medical devices includes the receiving and label-check fields we use when a shipment of PPE lands, so the check is signed off instead of assumed.

Building a spec for the year? The clinic supply and cost planner turns mask volume per room into case quantities, which is what a tender or an annual contract actually needs.

Related Reading

Frequently Asked Questions

Is ASTM F2100 a legal requirement in Canada?

No. It is a consensus standard published by ASTM International, and Canadian law does not incorporate it by reference. What Canadian law requires is a compliant label under section 21 of the Medical Devices Regulations and, for the importer or seller, an establishment licence under section 44. Buyers specify F2100 because it gives them a comparable set of test results, not because a regulator will issue a citation for its absence.

Why do so many Canadian mask boxes carry an ASTM level badge then?

Because the badge answers the buyer's question, not the regulator's. Hospitals, dental groups and long-term care operators write the level into their purchase specifications, and a supplier that cannot show a test report referencing the standard loses the order. The badge is a commercial currency that grew out of procurement practice.

What has to be on a mask label in Canada?

Section 21 lists the device name, the manufacturer's name and address, the device identifier, an indication of contents where they are not obvious, the expiry date where the device has one, the intended use and performance specifications where they are needed for proper use, the directions for use, and any special storage conditions. The information must be legible, permanent and prominent.

Is a surgical mask the same device class in Canada and the United States?

The US regulation is explicit: 21 CFR 878.4040 places surgical gowns and surgical masks in Class II with special controls, and leaves the rest of surgical apparel, including isolation masks and gowns, in Class I. Canada works from its own classification rules, so the classes are not interchangeable statements and should never be quoted as if they were.

Which is stricter for a mask, EN 14683 or ASTM F2100?

Neither is stricter in the abstract; they answer different questions. EN 14683 sets out types based on bacterial filtration efficiency and, for the Type IIR, resistance to splashes. ASTM F2100 layers filtration, differential pressure, fluid resistance and flame spread into three levels. A clinic should specify the one its infection prevention lead uses and ask for the test report that matches it.

Does a mask need a DIN or an NPN in Canada?

No. Those numbers belong to drugs and to certain disinfectants and antiseptics. A mask sold as a medical device travels under the Medical Devices Regulations instead, which is why you will see a device identifier and a manufacturer name rather than a DIN on the box.

What should I ask for when a supplier claims an ASTM level?

Ask for the test report, and check three things on it: the edition of the standard cited, the specific tests reported against each requirement, and the laboratory that ran them. A report without an edition is a marketing sheet, and a report that lists a level without the underlying measurements cannot be checked.

If a mask has no standard claim at all, can a clinic still buy it?

It can be bought and it can be worn, but it cannot be described as an ASTM-graded procedure mask, and it should not be written into an infection prevention policy as though it were. For tasks where the mask is the only barrier between the wearer and a splash, the missing test data is the risk, not the price.

Last updated: November 2026. CliniEco Medical is a licensed medical device establishment (MDEL #35334).

Already working with clinics? Become a regional representative.