How Are Impressions Disinfected on Arrival at a Canadian Dental Laboratory?

How Are Impressions Disinfected on Arrival at a Canadian Dental Laboratory?

A carton of impressions reaches a dental laboratory's receiving counter with a lab slip, a sealed bag and, often enough, no statement of what was done to the contents. What the bench reaches for first is not an instrument but a tub of hospital-grade disinfecting wipes, and whether that choice is defensible depends on paperwork that was written elsewhere. The question of how impressions are disinfected on arrival is answered in three different documents at once: the sending office's provincial infection-control guidance, the impression material manufacturer's instructions for use, and the laboratory's own written procedure. They rarely contradict one another outright, but they put the step in different hands, and a case in transit is where the difference becomes visible.

Two facts decide most of it. The first is timing: guidance places cleaning and disinfection at the patient, not at the courier, because blood and bioburden that dry on an impression surface are harder to remove and harder to verify later. The second is material tolerance: the material sets its own limit on how long it can sit in a disinfectant before the impression distorts, which is why the contact time printed on the disinfectant a receiving bench actually uses has to match the sheet packed with the impression material, and the laboratory's written procedure has to be read as one instruction rather than two.

What should the sending office have done before the case left?

The Ontario college's infection prevention and control guidance, in its dental laboratory asepsis section, puts the obligation on the office in plain terms: impressions, prostheses and appliances "should be cleaned and disinfected as soon as possible after removal from the patient's mouth, before drying of blood or other organic debris." The same section adds that "the manufacturer's instructions regarding the stability of specific materials during disinfection should be consulted," and that "wet impressions or appliances should be placed in an impervious bag prior to transportation to a commercial dental laboratory."

That is the whole of the sender's share: clean, disinfect, consult the instructions for use, bag it wet, send it. The reason the guidance puts it there rather than at the laboratory is not administrative. Disinfection performed in the operatory happens while the operator still knows what the impression contacted, and it happens before the material has had time to dry. A laboratory receiving bench can repeat the step, but it cannot recover the moment.

What the guidance does not do is name a product or a contact time. That silence is deliberate: the same document tells offices that materials must not be "damaged or distorted because of overexposure to disinfectants," which is a statement about the material's instructions for use, not about a universal soak.

What does the receiving bench do before anyone touches the case?

The American baseline is more explicit about the receiving end, and it is the document most often quoted when a laboratory writes its own procedure. The CDC dental infection-control guidelines direct that, where a case arrives without a statement of prior cleaning and disinfection, "the dental laboratory staff should perform cleaning and disinfection procedures before handling." They add a second rule that matters as much: if, during manipulation, "a previously undetected area of blood or bioburden becomes apparent, cleaning and disinfection procedures should be repeated."

The same guidance asks for a physical arrangement rather than a habit: "In the laboratory, a separate receiving and disinfecting area should be designated." Personal protective equipment is worn "until disinfection is completed," which in practice means the person opening the bag is already wearing medical-grade nitrile examination gloves, and the gloves come off after the case has been decontaminated and not before.

For a Canadian laboratory, the practical form of that sequence is short. Open in the designated area only. Read the case document before unwrapping. If the document states a method and a contact time, check that the stated method is one the material's instructions for use permit. If the document is missing, treat the case as contaminated and perform the step on site, then record that you did it rather than the sender.

White tub of hydrogen peroxide disinfectant wipes with a blue lid, 160 wipes per tub, standing on a plain background
The receiving bench does not need a special disinfectant; it needs one whose contact time the material's instructions for use allow.
Illustration of a 1 lb alginate canister with a mixing scoop beside it, CliniEco Medical
Alginate is specified in ISO 21563:2021, but the immersion limit that decides the method comes from the sheet packed with the canister.

Which case document should travel in both directions?

The CDC recommendation that Canadian laboratories tend to borrow verbatim is the fourth item in its laboratory list: "Include specific information regarding disinfection techniques used (e.g., solution used and duration), when laboratory cases are sent off-site and on their return." The return leg is included in the sentence, and it is the leg most often left blank. The same guidance says that if a laboratory does the final disinfection but provides no written documentation of the method, the dental office remains responsible for final disinfection before the appliance goes back in a patient's mouth.

That produces a case document with a small, fixed set of fields. It is not a form for its own sake: each field answers a question that an inspector, a laboratory quality programme or a recall can ask months later, and none of them can be answered from memory.

Field on the case document Question it answers Who completes it
Case or prescription number, office, date Which patient, which practice, which day Sending office
Item type and material, by name Which instructions for use govern the method Sending office
Disinfectant used and contact time Whether the method matched the material's limit Sending office
Bag sealed and intact on arrival Whether the case was exposed in transit Laboratory receiving
Repeat disinfection, if any, with method Whether the laboratory had to redo the step Laboratory receiving
Return-leg disinfection or sterilisation of the appliance What was done before the appliance re-entered the clinic Laboratory, before shipping back

Where does Canadian practice diverge from the American baseline?

Canada has no single federal instrument for this step. What binds a dental office is provincial college guidance plus provincial occupational health legislation; what binds a laboratory worker is the occupational health and safety regime of the province the bench sits in. The table below sets out what each jurisdiction actually supplies, so that a laboratory writing a procedure for cases arriving from more than one province knows which text it is copying.

Jurisdiction Instrument that governs the step What it settles What it leaves to the laboratory
Ontario RCDSO infection prevention and control guidance, dental laboratory asepsis section Clean and disinfect before transport, consult the instructions for use, bag wet impressions The written receiving procedure and its records
Quebec Ordre des dentistes du Québec infection-prevention guidance, read with the Charter of the French Language for the accompanying paperwork The clinical obligation, and the language in which case documentation may be written Method selection for each material received
United States CDC dental infection-control guidelines; OSHA bloodborne pathogens standard for worker protection The receiving-area requirement, PPE until decontamination, the case document in both directions Whether the laboratory or the office performs final disinfection

One Canadian wrinkle sits outside the college documents: transport. Where a shipment contains a specimen or a culture rather than a bagged impression, the Transportation of Dangerous Goods Regulations and the UN3373 category for biological substances apply, with training and packaging requirements that a courier of impression cases does not otherwise meet. A laboratory that receives both should keep the two routes visibly separate at the receiving bench, because the paperwork for one is not the paperwork for the other.

Do the standards set an immersion time for impression materials?

The reason a laboratory cannot publish a single soak time for everything it receives is that impression materials are tested differently and behave differently. Irreversible hydrocolloid — alginate — is specified in ISO 21563:2021, whose second edition consolidated the earlier hydrocolloid documents and covers requirements, test methods, labelling and instructions for use. Elastomeric impression materials and bite registration materials are specified in ISO 4823:2021, which has its own test methods and its own detail-reproduction requirements. Neither standard sets an immersion time; both require the manufacturer to state what the material tolerates.

That is where ISO 17664-1:2021 comes in, and it is the standard most often missing from a laboratory's source list. It specifies the information a device manufacturer has to provide for processing critical, semi-critical or sterilisation-intended devices, and the list of activities it covers includes "initial treatment at the point of use" and "transportation" alongside cleaning, disinfection and drying. An impression is a single-use item and is not reprocessed, so the standard does not govern the case as a device; it governs the sheet of paper that tells the receiving bench what the material will survive.

The consequence for both ends is unglamorous. A laboratory's procedure should name, for each material family it accepts, the methods the manufacturer permits, and should refuse a stated method that falls outside them — not because the method is ineffective, but because the record would then show a step the material was not cleared for. An office that uses one disinfectant for everything should expect a laboratory to ask which materials it is used on.

What must a receiving log hold, and why is a photograph not a record?

A photograph of a bag proves that a bag existed. It does not show the method, the contact time, the person, or whether the step was repeated, and it cannot be filtered by case when a recall reaches back six weeks. A receiving log earns its place when each row carries the case number, the date and time received, the sending practice, the method stated by the sender, the material's family, whether the bag arrived intact, any repeat disinfection with its method, and the initials of the person who released the case to production.

The retention period is not set by the disinfection step; it follows the record-keeping rule that already binds the practice or the laboratory, which is why a laboratory serving several provinces should keep one period that satisfies the longest of them rather than a different rule per client. The working test is simple: if a patient is later found to have been infectious, could the laboratory list every case that person's impressions touched, and the method used on each, without interviewing staff? A log that cannot answer that is a diary, not a record.

Where does a laboratory take this next?

Two things a practice can act on rather than read: a printable compliance log sheet that carries receiving dates, lot numbers and open-on dates and exports from the browser, and the clinic supply planner, which turns daily bench counts into cases per month for the lines a receiving area burns through.

Have a question about your own facility? Send it in and you will get a written answer specific to your setup, with the regulation or standard it is based on cited. Ask your compliance question.

Facility and multi-site buyers can ask about wholesale and multi-site ordering for case pricing and account setup. Reselling? become a distributor.

Related reading

Frequently Asked Questions

Does a dental laboratory have to disinfect impressions that arrive already disinfected?

No, provided the case document states the method and contact time and the stated method is one the material's instructions for use permit. Where no statement arrives, the laboratory performs cleaning and disinfection before handling, and where blood or bioburden becomes apparent during manipulation the step is repeated. The record should say which of those three situations applied.

Who is responsible for the final disinfection of an appliance returned to the office?

Either side can do it, but the documentation decides. If the laboratory performs the final step and documents the method, the office can accept the appliance; if no documentation accompanies the return, the office remains responsible for final disinfection before the appliance is seated. The requirement covers the return leg as explicitly as the outbound one.

Can one disinfectant be used for every impression material a laboratory receives?

Only if every material's instructions for use permit the same contact time. Alginate, specified in ISO 21563:2021, and the elastomers specified in ISO 4823:2021 are tested differently and tolerate immersion differently, and the manufacturer's stated limit is the one that binds. A single product can still be used across families where its label covers each of them at the stated time.

Is the impression a semi-critical device that has to be sterilised?

An impression contacts mucous membrane, but it is a single-use item and is not reprocessed for another patient, so sterilisation does not apply to the impression itself. What does have to be sterilised is the heat-tolerant hardware around it: metal impression trays and face-bow forks are heat-sterilised after each patient, while articulators and case pans are cleaned and disinfected between patients.

What has to be written on the case when it goes back to the dental office?

The same fields that travelled outbound, completed on the return: what was done to the appliance, with which product and for how long, and by whom. Without that, the office cannot show it verified the appliance before use, and the obligation to disinfect it falls back to the office.

Does a Quebec office have to write its case documentation in French?

The Charter of the French Language allows entries in a clinical file to be written in French or English at the writer's discretion, while permitting a health service to require French only, and it obliges the service to provide a French summary and a French version of any document on request, at its own cost. A bilingual case document is therefore workable, provided the French version is produced when it is asked for.

Is a spore test or a biotype check required for the receiving bench itself?

No. The receiving bench is a decontamination point, not a steriliser, and the monitoring requirements that apply to sterilisation cycles do not attach to it. What the bench needs is a written procedure, a designated area, PPE until decontamination is complete, and a log that can be filtered by case.

Sources

- Royal College of Dental Surgeons of Ontario, Infection Prevention and Control in the Dental Office, dental laboratory asepsis section — rcdso.org - Centers for Disease Control and Prevention, Guidelines for Infection Control in Dental Health-Care Settings — 2003, dental laboratory section and recommendations — cdc.gov - ISO 17664-1:2021, Processing of health care products — Information to be provided by the medical device manufacturer for the processing of medical devices, Part 1: critical and semi-critical devices, scope — evs.ee - ISO 21563:2021, Dentistry — Hydrocolloid impression materials, second edition — iso.org - ISO 4823:2021, Dentistry — Elastomeric impression and bite registration materials, fifth edition — iso.org - CSA Group, CAN/CSA-Z314:23, Medical device reprocessing — csagroup.org - Transportation of Dangerous Goods Regulations, SOR/2001-286, biological substances — laws-lois.justice.gc.ca - Occupational Safety and Health Administration, 29 CFR 1910.1030, bloodborne pathogens — osha.gov - Charter of the French Language, CQLR c C-11, sections 2 and 27 — legisquebec.gouv.qc.ca - Public Health Ontario, infection prevention and control resources — publichealthontario.ca

CliniEco Medical distributes clinic and laboratory consumables in Canada under MDEL #35334. Requirements that bind a specific practice remain the ones in its own provincial guidance, manufacturer instructions and written procedures.

Last updated: 14 November 2026.

Already working with clinics? Become a regional representative.