Three numbers decide whether a pouch seal holds: the temperature at the seal bar, the dwell time the film stays under it, and the pressure that holds film against paper while the polymer melts. ISO 11607-2:2019 requires the sealing process to be validated, which means the window those three numbers sit inside has to be established, challenged and recorded rather than inherited from whoever set the machine up. A validated process is one where any operator on any shift produces the same seal, and where a bad seal is detectable before the pack reaches a patient.
The practical difficulty is that the numbers do not come from the sealer alone. The film decides the temperature range, the paper decides how much pressure the seal needs, and the machine decides what you can actually adjust. This article separates those three, shows how a seal window is established with laboratory seals under ASTM F2029 and measured under ASTM F88, and sets out a validation protocol a clinic can run and defend, including the triggers that force it to be repeated.
The machine in this article is a constant-heat pouch sealer with a 12 mm seal, used with Class 4 self-sealing pouches or 76 mm roll stock. The same protocol works for any heat sealer, and the parameter logic is the same whether the head is constant-heat or impulse.
What does ISO 11607-2:2019 require a clinic to validate?
ISO 11607-2:2019 specifies "requirements for the development and validation of processes for packaging medical devices that are terminally sterilized", covering "forming, sealing and assembly of preformed sterile barrier systems, sterile barrier systems and packaging systems", and it is "applicable to industry, to health care facilities, and to wherever medical devices are packaged and sterilized" (ISO 11607-2:2019). A dental practice that seals its own pouches is inside that scope. The standard was amended in 2023 (Amendment 1, application of risk management), and the FDA recognises the consolidated second edition 2019-02 including Amendment 1 (FDA recognition, ISO 11607-2). Its requirements sit alongside the materials standard, ISO 11607-1:2019, which the FDA recognises separately (FDA recognition, ISO 11607-1).
Validation, in the standard's terms, is not a single test. It is a documented argument in three parts: the process is specified (which parameters, which limits, which material), the process is shown to work at the limits of those parameters, and the process is controlled in routine use so that drift is caught before it produces a bad pack. ISO/TS 16775:2021 explains how to apply both parts of ISO 11607 and states that it "does not add to, or otherwise change, the requirements" and is "not a basis for regulatory inspection or certification assessment activities" (ISO/TS 16775:2021). It is the useful interpretive text, not a second rulebook.
The companion requirement standard is ISO 11607-1:2019, which covers the materials and the sterile barrier system itself. The division matters: Part 1 says what the pack must achieve, Part 2 says how you prove your process reliably produces it.
Which three parameters define the seal window?
A seal window is the set of temperature, dwell and pressure combinations that produce a continuous seal strong enough to survive handling and peelable enough to open. Each parameter fails differently at each end.
| Parameter | What it controls | Too low | Too high | Where the limit comes from |
|---|---|---|---|---|
| Temperature at the seal bar | Whether the polymer coating reaches its melting range and wets the paper | Incomplete fusion — a seal that looks closed and peels apart, or a channel at the seal edge | Film shrinkage, curl, scorching, seal bleeding into the pack area | The film and pouch manufacturer's instructions for use; confirmed by laboratory seal curve |
| Dwell time | How long heat and pressure are applied, and therefore how far fusion progresses | Cold seal: continuous but weak, passes visual inspection, fails in the drawer | Over-fusion, brittle seal, film thinning at the bar, difficult peel | Machine capability, and the seal strength plateau measured under ASTM F88 |
| Pressure and contact | Whether film and paper are held in full contact across the seal width | Voids, channels, unwelded patches, especially at folds | Film squeezing out of the seal, thinning, deformation of the paper | Sealer specification and the pouch material; verified by seal appearance and dye test |
| Seal width and alignment | The area available to carry load and the path a channel must cross | Narrow seal, seal near the pack edge, seal crossing a fold | Seal too wide to peel cleanly by hand | Sealer specification (a 12 mm band on the unit used here) and pouch IFU |
Two points about that table decide how a clinic should read its own machine. First, the temperature limit belongs to the material, not to the machine: a sealer that holds 200 °C is only correct for a film qualified at 200 °C, and a new pouch supplier can invalidate the setting without any change having been made at the bench. Second, dwell and pressure are the parameters an operator can change by hand, which is exactly why they are the ones that must be locked down in a procedure rather than adjusted until a seal "looks right".
How is the window established before the validation run?
By making laboratory seals across a range and measuring them, which is what ASTM F2029 is for. It covers "laboratory preparation of heat seals and the treatment and evaluation of heat seal strength data to determine heat sealability of flexible barrier materials", and it states its own boundary clearly: it "does not cover validation procedures for production equipment", it is restricted to hot-bar or impulse sealing methods, it does not include seal strength testing (that is ASTM F88), and its stated purpose is to help establish "starting relationships for sealing flexible barrier materials" with additional guidance possibly needed for production settings (ASTM F2029-16(2021)).
The output is a curve rather than a number. Seals are made at a series of temperatures and dwell times, each is peeled under ASTM F88, and the result is plotted as seal strength against temperature or dwell. Three regions appear: too cold (strength rises steeply with more heat), a plateau (strength changes little across a range of settings), and too hot (strength falls again as the film thins or the seal becomes brittle). The plateau is the candidate window, because a process sitting in the middle of a plateau tolerates normal variation in heater temperature and operator timing.
ASTM F88 is the measurement that makes this possible, and its significance clause explains why the plateau matters for production as well as for development: seal strength is "a quantitative measure for use in process validation, capability, and control", a minimum level is a necessary package requirement, and an upper limit is sometimes desirable so the pack can be opened (ASTM F88/F88M-23). A window with a floor and no ceiling produces seals that hold and cannot be peeled.
One honest limitation applies to single-temperature machines. A constant-heat head holds one published temperature for the whole run instead of spiking per impulse, which is good for repeatability across a morning of packs, but it removes temperature as a variable you can tune. On such a machine the window is confirmed by dwell and pressure at the material's qualified temperature; if a new film needs a different temperature, the answer is a different sealer setting or a different sealer, not a longer dwell that compensates for a film running outside its range.
What does a validation run look like in a clinic?
The three-stage structure below is the conventional way to build the argument, whatever the sealer. The numbers in the last column are the evidence a reviewer will ask for; they are not a substitute for a written protocol.
| Stage | Question it answers | What is done | Evidence kept |
|---|---|---|---|
| Installation check | Is the machine installed and operating as specified? | Verify voltage and supply, seal width and band condition, heating behaviour, cutter, and a start-up seal after the warm-up period | Machine identity and serial, installation date, warm-up time, first seal result |
| Operational challenge | Does the process produce a good seal at the edges of the window, not only in the middle? | Seal packs at the lowest and highest dwell the procedure allows, at the qualified temperature and pressure; test each condition | Seal strength values per condition, visual result, dye result where specified |
| Performance qualification | Does the routine process, run by the people who actually work the bench, produce conforming packs? | Three consecutive production runs with real instrument sets, sampling packs from each run | Sample size per run, test results, accept/reject, operator, date, material lot |
Two habits make this defensible. Sampling is decided before the run and written into the protocol, because none of the ASTM methods fixes a sample size: ISO 11607-2 sets the requirement to validate, and the number of specimens per condition is a quality-system decision that must be justified rather than copied. And the acceptance criteria are written as numbers with a source — the pouch manufacturer's instructions for use, the material specification (for sealable pouches and reels in Europe, EN 868-5:2018 states the test methods and values), or the plateau established in the laboratory seals.
Where a pack is suspected rather than proven, a channel is confirmed with dye penetration under ASTM F1929-23, which locates channel defects in seals between film and porous sheet and is qualitative, while a gross leak anywhere in the pack is screened with ASTM F2096-11(2019): a pass means no channel was detected, not that the seal is strong. That is why the strength test and the leak test are both in the protocol rather than one standing in for the other.
When must the validation be repeated?
Revalidation is triggered by change, and the change is almost always to the material or the machine rather than to the operator. The list below is the one to write into the procedure, because each row alters something the original validation assumed.
| Change | Why it invalidates the old evidence |
|---|---|
| New pouch or roll supplier, or a new material lot with a different film | The film's melting behaviour and thickness set the temperature and dwell window |
| Switching between pouches and roll stock | Different material construction; a process validated on one format is not automatically valid on the other |
| Different seal width or a new sealing band | The seal area carrying load and the heat transfer path both change |
| Heater, thermocouple or controller replaced; machine serviced | The temperature the head delivers is the parameter being validated |
| Any change to the documented dwell, pressure or temperature setpoint | The validated window no longer describes the process in use |
| Change of sterilizer or sterilization cycle | The pack sees different pressure and temperature profiles during the cycle — the loading ASTM F1140/F1140M is built to evaluate |
| A run of seal failures in use or at inspection | The existing evidence has been contradicted by the process output |
Notice what is not on the list: a routine change of operator, a new box of the same material lot, or the passage of a fixed period. Time-based revalidation is a policy decision a facility can make, and many do — but it is not a substitute for change-based triggers, and a clinic that revalidates annually while ignoring a supplier switch has the interval without the control.
What fails in practice, and what does the failure look like?
The failure modes are few and they are recognisable at the bench. Most are visible on the seal before any test is run, which is why visual inspection of every pack under ASTM F1886/F1886M-25 remains the first line.
| Failure | What it looks like | Usual cause | First check |
|---|---|---|---|
| Cold seal or channel | Seal is closed but peels open with little force; a dye test shows a line of penetration | Dwell too short, temperature below the film's range, pressure too low, film not flat under the bar | Dwell setting and the start-of-shift seal strip; confirm the film's qualified temperature |
| Wrinkle across the seal | A crease runs through the seal band, with a thin or unwelded line along it | Pouch loaded off-square, pack overfilled, roll fed at an angle | Loading practice and pack size against contents |
| Fold-over at the seal | A doubled edge seals to itself, leaving a gap along the fold | Excess film folded back before sealing; pack too long for its contents | Whether the pack needed a larger pouch or a different roll width |
| Scorch, curl or shrinkage | Browned or wavy film, seal bleeding into the pack, difficult peel | Temperature too high or dwell too long for that film | Temperature setting against the material IFU; check the plateau |
| Seal only partly across the width | Ends welded, middle open | Pressure uneven along the bar, worn band, debris on the bar | Bar condition and cleaning; alignment of the pouch in the sealer |
The pattern worth noticing is that two failures point in opposite directions. A channel says not enough heat or time; a scorch says too much. A clinic that responds to both by turning the same dial up has no window, only a habit.
What must the validation record contain?
A validation file that cannot be reproduced is a folder, not evidence. The fields below are the minimum that connect a result to the machine, the material and the parameters that produced it.
| Field | Why it belongs in the record |
|---|---|
| Machine identity, serial and location | A validation describes one sealer, not a model |
| Parameter set: temperature, dwell, pressure, seal width | The window being validated, stated as numbers |
| Material identity and lot, with format (pouch or roll) | Film and paper determine the window |
| Protocol revision and acceptance criteria with source | Shows the pass line was set before the test, not after |
| Specimens per condition and how selected | Sampling method is part of the argument |
| Results by condition: seal strength values, visual outcome, dye outcome | Trendable data, not a single verdict |
| Operator and date for each run | Ties the evidence to the people and shifts in scope |
| Deviations and dispositions | What failed, what was rejected, what changed afterwards |
| Revalidation triggers reviewed | Confirms the change list was considered, even when nothing changed |
Where does the Canadian requirement come from?
Canada's reprocessing standard carries the requirement into the health care setting. CSA Z314:23, the second edition published in 2023, extends coverage to professional offices and private practices and, among its revisions, addresses the reprocessing of sterile barrier systems and consumables alongside manufacturer's instructions for use (CSA Z314:23). Public Health Ontario's provincial guidance document supplies the operational rule that makes the file worth keeping: at point of use "the integrity of the packaging and the equipment/device must be checked", a pack whose integrity is compromised is no longer sterile and must be reprocessed, and shelf life is event-related rather than time-related (Public Health Ontario, provincial guidance on cleaning, disinfection and sterilization of medical equipment and devices in all health care settings, recommendation 86). Health Canada's guidance for reusable devices adds the document side: the directions for use must carry the reprocessing and sterilization information required by paragraph 21(1)(i) of the Medical Devices Regulations (Health Canada guidance). A validation file is what lets a clinic answer when a run of packs is questioned: it shows the process was defined, challenged at its limits, and monitored.
CliniEco Medical supplies the sealer, pouches and roll stock described above, and distributes them under Health Canada MDEL #35334. The validation logic here follows ISO 11607-2 and applies to any heat sealer; the machine is the variable, the requirement is not.
Groups that order sealers and packaging for more than one location can route the order through wholesale and multi-site ordering, which keeps the material and the machine on the same purchase record. Reselling? become a distributor.
Recording seal checks already? The compliance log centre has a printable seal validation sheet and a browser-based generator for parameter sets, test results and reject counts, with no account needed.
Have a question about your own sealer? Send the machine, the pouch or roll you use, and the failure you are seeing, and you will get a written answer citing the standard or regulation it rests on. Ask your compliance question.
Related reading
- Pouch Sealer Validation Records: Temperature, Pressure and Seal Integrity Proof for Inspections
- ISO 11607-1 vs ISO 11607-2: Sterile Packaging Validation Roles
- Seal Integrity Testing for Sterile Pouches: ASTM F88, F1929 and F1886
- Sterile Barrier Packaging: What ISO 11607 Requires of Clinics
- Sterilization Pouch Sealing Failures That Show Up Only at Inspection
- Sterile Barrier System Terms: Pouch, Reel, Wrap and Container Explained
Frequently Asked Questions
How do I know my seal window without laboratory data?
Start from the pouch manufacturer's instructions for use, which state the sealing conditions the material was qualified for, then confirm on your own machine with a dwell range test: make seals at the lowest and highest dwell your procedure allows, peel them under ASTM F88, and check that both ends of the range produce seals inside the specification. A laboratory seal curve under ASTM F2029 is the rigorous route; a documented two-point challenge on your own material is the minimum.
Can a constant-heat sealer be validated the same way as an impulse sealer?
Yes, with one difference in what you can adjust. The validation logic — specify the parameters, challenge the limits, monitor in routine use — is the same. A constant-heat head holds one temperature for the whole run and does not spike per impulse, so temperature is not a variable you can tune; dwell and pressure are. That makes material qualification at the head's published temperature the first question, and dwell the parameter you challenge.
How many packs must be tested in each validation run?
No standard sets the number. ISO 11607-2 requires the sealing process to be validated and the ASTM methods define procedure and measurement, not sample size. The number of specimens per condition, the number of runs and the accept/reject rule are decisions your protocol must state and justify — a risk-based plan with more specimens at the window edges and after a material change is the usual approach.
Does a three-run validation have to be three days?
Not necessarily; it has to be three consecutive production runs that are independent of each other, run by the people who normally work the bench, with packs sampled from each. Whether that is three runs on one shift or three across a week is a facility decision, provided the runs are not conducted as a special exercise with extra care that will not be repeated.
What forces a revalidation after a sealer repair?
Any repair that touches the heating path: a replaced heater, thermocouple, controller or sealing band, or a service that changed the pressure or alignment of the bar. The temperature the head delivers is the parameter being validated, so once it has changed, the earlier evidence describes a different machine. The same logic applies to a change of film, pouch format or seal width.
Is a dye test needed in every validation run?
No, and the two tests answer different questions. ASTM F88 measures seal strength and is the quantitative evidence that the process sits inside its window. ASTM F1929 locates a channel through the seal and is pass/fail. A protocol that uses F88 at every condition and F1929 at the window edges, or whenever a channel is suspected, is coherent; one that relies on a single dye test to prove a process is not.