Fissure Carbide Bur: Sizes, Markings and Colour Codes Explained

Two rolls of autoclave indicator tape used to seal and label instrument pouches before the cycle

Fissure Carbide Bur: Sizes, Markings and Colour Codes Explained

A Winnipeg clinic pulled five "557" burs off the same shelf and two of them cut noticeably slower. The catalogue numbers matched; the flute pattern and the age of the stock did not, and nobody had written either on the drawer label. Burs are the lowest-cost item in the operatory and the easiest to order wrongly, because the printed number is a commercial shorthand and a bur that comes back from the cycle in a Class 4 dual-indicator pouch looks identical to the one beside it.

What does a fissure bur cut that a round bur cannot?

A fissure bur has a flat-ended or slightly tapered working end with straight blades along it. That geometry produces a flat floor and a defined wall, which is what a shoulder, a box or an extension of an existing prep needs. A round bur gives a concave floor and is the wrong tool for that cut.

The straight fissure family covers most of this work and the tapered family handles converging walls. Crosscut versions add blades across the tip, so they cut on axial as well as lateral pressure, which is why they behave differently in the same handpiece.

Number Working end Cut Where it earns its place
556 to 559 Straight fissure, increasing length Plain Cavity walls, shoulders
170 to 172 Tapered fissure Plain Converging walls
699 to 702 Fissure, crosscut Crosscut Bulk removal, axial pressure

What do the numbers and digits on a bur actually encode?

Self-sealing Class 4 dual-indicator sterilization pouch, 2.5 x 4 inch, with the process indicator strip visible

Two systems sit on one instrument and they are not interchangeable. The digits a dentist says out loud — 557, 701 — come from the supplier catalogue and describe a familiar shape. Underneath that, ISO 6360-1:2004 defines a 15-digit number in which a three-digit shape code forms the first group, and the edition was confirmed on 1 July 2024.

Shank dimensions are separate: ISO 1797:2017 covers shanks for rotary and oscillating instruments and was confirmed on 16 September 2022.

What do FG, RA and HP mean on the neck of the bur?

The shank decides which handpiece accepts the bur, and getting it wrong is the commonest ordering error.

Marking Shank Fits
FG Friction grip, 1.60 mm High-speed air turbine
RA Latch type, 2.35 mm Contra-angle
HP Straight, 2.35 mm Laboratory handpiece

Two rolls of autoclave indicator tape used to seal and label instrument pouches before the cycle

Does the colour band tell you anything you can rely on?

Not the size. Colour bands and coloured shank rings follow a maker's product-line system, so the same colour can mean different things from two suppliers. For diamond instruments, ISO 7711-1:2021 sets general requirements and replaced the 1997 edition, which was withdrawn on 10 November 2021 — useful when a page still cites the old edition as proof of compliance.

The safe habit is to order by the number on the shank plus the shank type plus the flute or grit description, and to put all three on the drawer label sheet.

What does a bur station consume besides burs?

Every bur that leaves the drawer was cleaned and packed, so the drawer budget is never just burs: a bath with a multi-enzyme ultrasonic cleaning solution, an autoclave indicator tape where a pouch needs sealing, and a 24-hour biological indicator on the monitoring schedule the load requires.

Ordering for a clinic, lab or care home? Wholesale and multi-site ordering covers case pricing and account setup, and the B2B ordering collection lists the lines stocked for institutional buyers. Reselling? become a distributor.

Stocking a full operatory? Our dental practice supplies page groups burs, pouches and monitoring consumables in one place.

References

  1. ISO 6360-1:2004 — Dentistry: number coding system for rotary instruments, Part 1: general characteristics (confirmed 1 July 2024) (checked 31 October 2026)
  2. ISO 1797:2017 — Dentistry: shanks for rotary and oscillating instruments (confirmed 16 September 2022) (checked 31 October 2026)
  3. ISO 7711-1:2021 — Dentistry: diamond rotary instruments, Part 1: general requirements (replaced the 1997 edition, withdrawn 10 November 2021) (checked 31 October 2026)

Printable companion: the sterilization log templates cover the pouch-and-cycle record that sits behind every bur station.

Rebuilding a bur drawer from scratch? The sterilization self-check covers the processing side so the two lists line up.

Related Reading

Frequently Asked Questions

What is a fissure bur used for?

A flat or slightly tapered working end with straight blades, used to open a cavity wall, cut a shoulder or extend a prep where the floor has to stay flat. A round bur cannot produce that floor.

What do FG and RA mean on a bur?

The shank type, not the cutting end. FG is friction grip for an air turbine, RA is a latch-type shank for a contra-angle, and HP is a straight shank for a laboratory handpiece.

Is the colour band on a bur a size code?

It is not. The number printed on the shank identifies the shape and the catalogue identifies the size; colour bands follow each maker's own system and change between product lines.

Last updated: November 2026. CliniEco Medical is a licensed medical device establishment (MDEL #35334).

Already working with clinics? Become a regional representative.