Does a Canadian clinic have to register its autoclave as a pressure vessel?
An autoclave in a Canadian clinic sits under two regimes at once. The first is the reprocessing routine every staff member knows: clean, pouch, load, indicator, log. The second is a mechanical file that belongs to the building, not the treatment room, and is not about sterility at all. Keeping a spare set of 24-hour self-contained biological indicators, 25 to a pack covers the first track; the second track starts on the nameplate.
What makes an autoclave a pressure vessel in Ontario?
The Technical Standards and Safety Act, 2000 and its regulation for boilers and pressure vessels, O. Reg. 220/01, govern the design, construction, installation, operation and inspection of pressure equipment in the province, and the code of record they point to is CSA B51. TSSA, the Technical Standards and Safety Authority, administers both. A steam sterilizer chamber that holds pressure and temperature above the ambient condition is pressure equipment in that sense, and TSSA's own owner notices list autoclave and sterilizer as a pressure equipment type alongside piping, deaerators and fired boilers.
The regulation does not catch every machine: section 2 excludes, among other things, a pressure vessel holding gas, vapour or liquid at a maximum allowable working pressure of 15 psi (103 kPa) or less, so the practical question is not "is it an autoclave" but "what does the plate say".

How can a clinic tell whether its unit is registered?
Read the nameplate before reading any invoice. A vessel registered for the Canadian market is stamped with a Canadian Registration Number, the maximum allowable working pressure, the design temperature and the year of manufacture. Registration is a design approval held by the manufacturer, and the number travels with the unit.
| Document | Where it lives | What it proves |
|---|---|---|
| Nameplate with CRN | On the vessel itself | The design was registered for Canada |
| Certificate of Inspection | Clinic file, expiry visible | TSSA inspected the installation before service |
| Periodic inspection report | Clinic file, dated inside the window | The vessel was re-inspected on schedule |
| Sterilization load log | Reprocessing file | Instruments were monitored biologically and chemically |

If the plate carries a CRN and the file has no Certificate of Inspection, the gap is not a paperwork nuisance: a unit can be registered in design and still be uninspected at the point of installation.
Which sterilization records sit alongside the pressure paperwork?
The reprocessing side is set by the College standard, not by TSSA, and in Ontario dental practice it means a biological indicator for each sterilizer on each day it is used and for each type of cycle used that day, with a control vial on every day indicators are incubated. The load log is kept on site for one year and on file for five. A Type 1 process indicator on the pouch outside and a Type 4 or Type 5 indicator inside complete the picture, which is why clinics order indicator tape in a three-roll set and Class 4 self-sealing pouches with a dual indicator as one consumable line rather than two.
Setting up the reprocessing file for the first time? The sterilization compliance desk walks a single-room clinic through the log fields and the monitoring schedule.
The dental practice supplies page groups the packaging, monitoring and cleaning lines behind that routine.
Ordering for several chairs, a lab or a care home? Wholesale and multi-site ordering covers case quantities and account setup, and the B2B wholesale collection lists the lines stocked for institutional buyers. Reselling? become a distributor.
References
- Boilers and Pressure Vessels, O. Reg. 220/01 under the Technical Standards and Safety Act, 2000 (checked 5 November 2026)
- TSSA boiler and pressure vessel identification form, listing autoclave and sterilizer among pressure vessel descriptions (checked 5 November 2026)
Printable companion: the instrument cleaning and sterilization log holds the load line, the cycle type and the indicator result that sit beside the pressure paperwork on an inspection table.
Match the indicator and pouch order to the number of loads the room actually runs: the sterilization monitoring usage calculator converts patient volume into loads per week.
Related Reading
- Preventive Maintenance Schedules for Steam Sterilizers: Gaskets, Filters, Chambers and Calibration
- How Long Should Canadian Clinics Keep Sterilization Records?
Frequently Asked Questions
Does every dental autoclave need a TSSA certificate of inspection?
Not every unit. O. Reg. 220/01 exempts equipment inside the thresholds in section 2, one of them a pressure vessel holding gas, vapour or liquid at a maximum allowable working pressure of 15 psi (103 kPa) or less, so the answer starts on the nameplate and is confirmed with the manufacturer or TSSA.
How often does a pressure vessel inspection come due?
The interval is set in the TSSA Code Adoption Document rather than by the clinic, and the owner must request the next inspection from the insurer or from TSSA before the expiry date printed on the Certificate of Inspection.
Is the pressure vessel certificate the same as spore testing?
No. They are two separate duties over the same machine. The certificate covers the mechanical safety of the vessel, while the College standard covers what happens to instruments, and an inspection can ask for both sets of paper on the same day.
Last updated: October 2026. CliniEco Medical is a licensed medical device establishment (MDEL #35334).