Drain your CPAP water chamber every morning, even if you will use the machine again that night. Standing water at room temperature is exactly what microorganisms need, and the humidifier chamber is the part of a CPAP circuit most likely to develop biofilm. This guide lays out the daily and weekly routine, explains why distilled water matters, lists what damages a chamber, and covers when to replace it — practical home-care guidance for Canadian CPAP users.
Buying a nebulizer? Distributed in Canada by CliniEco Medical, Toronto.
CliniEco CPAP Accessories Pack · CliniEco CPAP Compatible Hypoallergenic Filter · CliniEco CPAP Humidifier Water Chamber · Wholesale & clinic accounts
Products referenced in this guide
Quick facts: chamber care in five lines
- Empty and air-dry the chamber every morning; rinse before every refill.
- Wash weekly in warm water with mild dish soap, then rinse until no residue remains.
- Distilled water only. Tap water leaves mineral scale that gives biofilm a surface to hold.
- No dishwasher, no bleach, no alcohol, no aromatic cleaners — they degrade the plastic and the seal.
- CliniEco Medical is a licensed medical device establishment (MDEL #35334). CliniEco stocks a compatible replacement water chamber and two-pack of hypoallergenic filters.
Why the Daily Emptying Habit Matters
The chamber holds warm water while the machine runs, and warm, still water left between uses is a growth medium. Emptying and air-drying the chamber each morning breaks that cycle before it starts. Skip the habit for a few days and you may notice a film or an odour that simple refilling cannot fix.
Heated tubing does not change this routine. Heated tubing reduces condensation inside the hose, but the chamber still sits with leftover water when the machine is off, so it still gets emptied daily.
The Weekly Clean, Step by Step
Most manufacturers ask for a full wash once a week, with a fresh-water rinse whenever you refill. A straightforward routine looks like this:
- Disconnect the chamber from the machine and from the tubing.
- Wash it in warm water with mild dish soap, using a soft cloth or a brush made for the purpose. Skip abrasive scrubbers that scratch the plastic.
- Rinse thoroughly so no soap residue remains; residue can irritate airways and can trap new buildup.
- Air-dry completely on a clean towel, then reassemble only when every surface is dry.
Your device manual is the final word — some manufacturers recommend specific cleaning agents, and a few sell cleaning brushes shaped for their own chamber.

Use Distilled Water: Tap Water Is the Problem
Tap water carries dissolved minerals — calcium and magnesium — that deposit as scale on the heating plate and chamber walls. That scale film gives biofilm a surface to cling to and can reduce the humidifier’s output over time. Distilled water has the minerals removed, which keeps the chamber and heating element cleaner for longer. In Canada, distilled water is easy to find at pharmacies and grocers, typically in the same aisle as baby supplies and first-aid items.
How Often Does Each Part of the Circuit Need Cleaning?
Manufacturers differ in the detail, but the shape of the schedule is the same across the major device families: the parts that touch your face and hold water get daily attention, the parts that carry air get a weekly wash. The table below is the schedule ResMed publishes for its own equipment, which is a reasonable starting point if your manual has gone missing — and no substitute for it.
| Part | Daily | Weekly | Replace when |
|---|---|---|---|
| Water chamber | Empty and wipe; refill with fresh distilled water | Wash with mild detergent and warm water; air-dry | Cracks, permanent clouding, stubborn scale, deformed gasket |
| Mask cushion | Wipe the skin-contact surface | Wash with mild detergent | Torn, stiff, or leaking at the seal |
| Headgear and frame | — | Wash and air-dry | Stretched so the mask will not hold position |
| Tubing | — | Wash and hang to drain, out of direct sun | Punctured, or will not dry inside |
| Filter | — | Check; replace on schedule | Discoloured, or the manual's interval has passed |
Schedule as published by ResMed for its own equipment; your device manual overrides it wherever the two differ.
The step that gets skipped is drying. Every part in that table wants to air-dry completely, out of direct sunlight, before it goes back together. Reassembling a damp chamber is how a clean part becomes a growth surface again by morning.
Is Distilled Water the Only Option?
Distilled is the option that removes the mineral load, and minerals are the problem: calcium and magnesium plate onto the heating plate and the chamber wall, and that film is what biofilm holds onto. The device manuals are consistent on this — the chamber is filled with distilled water, and the water is replaced before each use rather than topped up.
| Water | What it leaves behind | Practical consequence |
|---|---|---|
| Distilled | Nothing — minerals removed by distillation | Slowest scale build-up; the water the manuals name |
| Tap | Calcium and magnesium scale | Film on the heating plate, reduced humidifier output, biofilm surface |
| Bottled drinking water | Some mineral content, varies by brand | Better than tap, not the same as distilled |
| Boiled tap water | Minerals remain after boiling | Boiling addresses organisms, not scale |
Comparison for home users; where the device manual names a water type, follow the manual.
If distilled water is unavailable for a night, the manuals of several manufacturers allow drinking-quality water as a fallback, with the chamber washed and dried the next morning. What is not a fallback is a routine: tap water every night is how a chamber scales out in a season, and scale that resists cleaning is one of the replacement triggers below.
What Happens If the Weekly Wash Is Skipped?
Usually nothing visible for a week or two, which is exactly why the habit slips. What builds is a film on the chamber wall and around the gasket seat — the part you cannot see with the lid on. By the time it is visible, the chamber is being cleaned to remove something rather than maintained to prevent it, and a chamber cleaned hard every month has a shorter life than one washed gently every week.
The commercial ozone and UV accessories marketed for CPAP circuits do not replace washing: the detergent step is what removes the film, and no device in that category does it for you. Wash first, and treat any accessory as an addition rather than a substitute.
How Do You Tell a Failing Chamber From a Dirty One?
Most chambers are replaced late, not early — the user notices a smell or a wet mask and lives with it for a month. The useful skill is telling the three states apart: a chamber that needs washing, a chamber that needs water discipline, and a chamber that is finished.
| What you see | What it usually means | What to do |
|---|---|---|
| White film that will not rinse away | Mineral scale from tap water, baked on by the heater plate | Switch to distilled water; if the film survives a vinegar soak and a soft rinse, replace the chamber |
| Hairline crack near the seal or the fill line | Thermal cycling and handling; the plastic has fatigued | Replace immediately — a cracked chamber leaks onto the heater plate and into the hose |
| Permanent clouding or a haze that will not clear | Heat damage, or a chamber that has been washed above the temperature the manual allows | Replace; clouding is the plastic surface going, not dirt on it |
| Flattened or discoloured gasket | Age, or repeated removal and refitting | Replace the chamber, or the gasket where the manufacturer sells it separately |
| Pink, black or grey speckling in a scratch or corner | Biofilm forming where the surface can no longer be cleaned | Replace and review the drying routine — a chamber left full and closed between nights is the usual cause |
| Water in the hose in the morning | Overfilling above the line, or condensation with the machine below bed height | Fill only to the line, keep the machine level with or below the mattress, and drain the hose before use |
Two of those rows are the ones users argue about. Scale that "just looks like a stain" is a surface that will never be clean again, and a chamber left full of water all day is a chamber growing a biofilm in the one place the airflow passes. Neither is a cleaning problem at the point you notice it — both are replacement decisions, and the replacement is the cheap half of the equation compared with a service visit for a machine that has been pulling moisture into its blower.
Where a replacement is needed, match the chamber to the machine rather than to a photograph: the model number on the base plate, the shape of the gasket and the way the chamber seats are the three things that decide fit. A compatible replacement chamber is listed with the models it fits, and the same order usually carries the replacement filters that are changed on the same schedule.
Related Reading
Keeping the rest of the circuit on schedule:
- how many chambers a clinic or home-care caseload gets through in a month
- standard, slimline and heated tubing, and which one your machine takes
- an audit checklist for CPAP accessory packs
What Not to Do
- No dishwasher. High heat and harsh detergents can warp the chamber and damage its seal.
- No bleach, vinegar, or harsh disinfectants unless your manual explicitly allows them; they degrade plastics and seals and leave fumes behind.
- No abrasive pads — scratches become hiding places for buildup.
- No overfilling. Water above the max line can back up into the tubing or the machine.
When to Replace the Chamber
Replace the chamber when you find cracks, cloudiness that will not wash off, scale that resists regular cleaning, or a gasket that has deformed or no longer seats snugly. A cracked chamber can leak water into the machine itself — a far more expensive failure than buying a replacement part.
Compatibility and spares
Chambers are model-specific. A chamber from another brand or a “universal” part may look similar but seal poorly, so match the part number in your manual. The same logic applies to the rest of the circuit: when the chamber is due, check the mask cushion, tubing, and filter at the same time. CliniEco offers CPAP accessory kits with compatible mask, tubing, and filter replacements to make scheduled swaps straightforward. In Canada, CPAP machines and their accessories are regulated as medical devices by Health Canada, so components should come from suppliers that can document compatibility with your device.
For households managing more than one respiratory therapy — CPAP at night and nebulized medication during the day, for example — CliniEco also carries a desktop compressor nebulizer for aerosol therapy, so both sides of home respiratory care stay on one supply list.

FAQ
Can I top up the chamber instead of emptying it?
No. Topping up concentrates whatever the water has already picked up and leaves the chamber wet between uses, which is the condition the daily empty is meant to break. Empty it in the morning, let it air-dry, and fill with fresh distilled water at night.
Do ozone or UV cleaners replace washing the chamber?
They do not. The detergent wash is what lifts the film off the plastic; a ozone or UV accessory does not remove residue and is not a substitute for the weekly wash in any manufacturer's instructions. Wash and dry first, and treat accessories as extras.
How often should I clean my CPAP water chamber?
Empty and rinse it every morning, and give it a full wash with mild soap and warm water once a week — or on the schedule in your device manual. Always let it dry completely before reassembly.
Can I use tap water in a CPAP humidifier?
Some manuals allow tap water in a pinch, but it is not recommended as a daily habit. Minerals in tap water leave scale that protects biofilm and can reduce humidifier output over time. Distilled water keeps the chamber cleanest and is the standard advice for regular use.
How often should a CPAP water chamber be replaced?
There is no universal interval — follow your manual, and inspect the chamber each week while you clean it. Replace it when you find cracks, permanent clouding, stubborn scale, a worn gasket, or any leak. Catching those signs early protects the machine.
Can a cracked water chamber be repaired?
No. A crack in a chamber is a fatigue failure in the plastic, and no adhesive is rated for a warm, wet, constantly flexing part that sits above electronics. Replace the chamber — a leak that reaches the heater plate or the blower turns a low-cost part into a machine repair.
How do I know a replacement chamber will fit my machine?
Match three things: the model number printed on the base of the machine, the shape and seating of the gasket, and the fill line position. A listing that names the compatible models is the starting point, and your own manual is the final word — a chamber that seats loosely will leak air before it leaks water.
Need these supplies for your facility? CliniEco Medical serves Canadian clinics, laboratories and long-term care homes. Open a wholesale account for institutional pricing.
Tracking CPAP water-chamber and filter replacements? The clinic supply and cost planner estimates monthly volumes from your patient count.
Change the patient count or replacement interval and the planner on that page re-costs the line in CAD.
Setting a cleaning and replacement schedule for therapy equipment? Ask a sterilization compliance specialist how the requirement reads for your setting, with the reference cited.
More guides in this category
Explore more guides in this category:
- CPAP Tubing Sizes Explained: Standard, Slimline, or Heated?
- Sterilization Acronyms: BI, CI, SAL and Bowie-Dick Explained
- Autoclave Downtime Costs: A Model for Unplanned Service Visits
Browse our home care supplies.
Browse our therapy devices.