Cost per Load: Sterilization Consumables for a Canadian Dental Clinic

Short answer: cost per load is the sum of four consumable lines divided by loads, and the dominant line is usually the pouch, not the indicator. A clinic that tracks only the indicator price is optimising the smallest part of the number. Build the figure from your own load count and pack count, then use it to compare suppliers on the only unit that matters for a budget.

The consumables in the calculation are CliniEco self-sealing sterilization pouch, 2.5 x 4 inch, Class 4 dual indicator, 200 per boxClass 4 self-sealing pouches, autoclave indicator tape, Class 5 integrators and biological indicators.

Which consumable dominates cost per load?

Almost always the pouch, because it is consumed per pack rather than per load. A load of ten packs uses ten pouches and possibly one integrator. Cost per load therefore scales with pack count, and the fastest way to lower it is to fit more instruments into each pack correctly, not to buy a lower-cost indicator.

Line Consumed per Driver of total cost
Pouch Pack Packs per load and size mix
Tape Pack Packs per load, roll length
Class 5 integrator Load or process challenge device Loads per day
Biological indicator Sterilizer per day of use Number of sterilizers
Class 4 self-sealing sterilization pouch with dual indicator

How do you convert case price into cost per load?

Cost per load = (pouches used × pouch unit cost) + (tape used × tape unit cost) + (integrators used × unit cost) + (indicators used × unit cost). Unit cost comes from case price divided by units per case, and case price must be the delivered price, because a lower case price with higher freight produces a higher unit cost.

Run the arithmetic at the case level once a quarter, not per order. Per-order arithmetic hides the effect of freight, and it is the freight and the minimum order that move the number more than a few percent off a list price.

CliniEco 24-hour biological indicator, 50-count pack

Where does cost per load hide waste?

Three places, and none of them appear on a purchase report. First, oversized pouches for small sets, which consume the same labour and more material. Second, re-pouching after a seal failure, which consumes two pouches for one pack. Third, a load repeated because an indicator was missing, which consumes a second full set of consumables plus staff time.

Each of those is a process fix rather than a purchasing fix, which is why cost per load should be reviewed by the person who runs the bench and not only by the person who signs the order.

Should a clinic buy integrators by load count or by case?

Buy by case and monitor by load count. Integrator consumption is predictable from the number of loads and the number of sterilizers, so case quantities are easy to plan, while a per-load purchase pattern adds freight and handling for no clinical benefit. A 100-count box of Class 5 integrators covers a single-sterilizer clinic for months at normal volume.

Download the printable load and indicator log, run the sterilization self-check before an inspection, and ask a compliance specialist if a class, a pack or a record is unclear.

Related reading

related monitoring practice; the consumable behind it; the next question clinics ask; sterilization compliance hub.

Frequently Asked Questions

Does cost per load include staff time?

The consumable figure does not. Add staff time separately if you are comparing a manual sealing process against a heat sealer, because the labour difference is usually larger than the material difference.

Why is the pouch the largest line?

Because it is consumed once per pack while an integrator is consumed once per load. Ten packs in a load means ten pouches against one integrator.

Should the lowest-cost pouch be used for all sets?

No. Pouch size should match the set, and an oversized pouch for a small set costs more per pack and seals less reliably at the fold.

CliniEco Medical is a licensed medical device establishment (MDEL #35334).

Ordering for a clinic, lab or care home? Wholesale and multi-site ordering covers case pricing and account setup, and the B2B wholesale collection lists the lines stocked for institutional buyers. Reselling? become a distributor.

Already working with clinics? Become a regional representative.